I have looked at the Cisco Feature Navigator and according to the output with IOS 12.4(15)T1 thru T13 there is support for multiple SSID's and the feature "Multiple Basic Service Set ID" should be supported.
When I try to invoke that command mbssid on my Dot11 interface I get 'Invalid' response. Am I missing something here? Is the Feature Navigator misleading me or am I doing something wrong?
All I want to do is broadcast both SSID's that I currently have configured. Currently only one guest mode SSID is allowed and broadcast.
I have some 1130AG access point and I'd like to have :
- Multiple broadcasted SSIDs (because most of my clients are OSX and OSX doesn't deal with hidden SSID at all ! the clients have to enter the data each time which for WPA2 enterprise is really annoying) - Dynamic VLAN assignement (so my clients don't have to know to which VLAN they belong and so I can easily change them from one to another).
As it turns out, it's apparently not supported to have both. But I can't understand WHY ? What exactly is the relation between those features ? What's the underlying technical constraint ?
I can understand the cipher suite must match between all the dynamic vlan because of the way wlan works, but for this, I really don't see what the problem is ... (Especially since I only have one of the SSID that needs dynamic assignement, the other is really the 'guest' one).
I was upgrading the firmware of the WRT54G router when the notebook´ screen closed and it went to standby mode. It was sttoped the upgrade process.Now only the ports and Internet LEDs light up, but the power LED is off.I also cannot connect to the navigator for show the administrator´s window. What is the procedure to recover the operation of the router in a situation like this?
I am very new to using the CISCO IOS. Here is the situation: I have a CISCO 851W router in the garage that I want to connect to my Linksys router in the office, which is connected to the internet. The 851W is connected from it's WAN port to Lan port 1 of the Linksys router. Now, currently that ethernet cable is a straight-through cable. Does it have to be crossover? If so, I can fix that.So I have no idea how to give the 851W internet access I am a total CISCO noob. I will leave it to you guys to recommend what IP to assign the router and subnet.
I am trying to configure QoS on my Cisco 851w router using the class-map command.However it won't accept the class-map command.The router is running cisco IOS version 12.4(15)T10 "C850-advsecurityk9-mz.124-15.T10.bin".
My 851W will not complete the boot up process, here is the output during bootup(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013. Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Wed 18-Aug-10 02:37 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814ECE54This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
I have been trying to get my 851W to work with DDNS for a long while now. In fact I walked away from the problem in frustration and loaded DD Client on a Linux box until I had time to re-visit this. The folks at Zone Edit were not able to offer much with CLI problems.
When I debug DDHS updates I get to a point where the the router tries to resolve the DDNS update address and fails.So I have a number of questions:
a) Is this error the result of lack of DNS server names written to the config?
b) My WAN interface is a DHCP client to my modem. If the DDNS updater does need to resolve a name, shouldn't the DNS server info be provided by the DHCP process for the WAN interface? How do I ensure that name servers are automatically assigned for the DDNS updater to use?
I have a CISCO 851W router in the garage that I want to connect to my Linksys router in the office, which is connected to the internet.The 851W is connected from it's WAN port to Lan port 1 of the Linksys router. Now, currently that ethernet cable is a straight-through cable. Does it have to be crossover? If so, I can fix that.
I want the default gateway for the CISCO router to be 192.168.2.1. I am not sure how to configure that. [URL]
Router A is the main router which Router B tunnels into connect to the location.Router A has a static IP address and Router B has a dynamic I am coming in new on the project so I did not setup this router and I am slightly confused. The tunnel is working however, the sites are not able to share files. Router B would like to be able to see all files on Router A and share printers etc...how the VPN is setup, IP addressing scheme and NAT.
Router A Config
Using 3695 out of 131072 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname XXXXXX!boot-start-markerboot-end-marker!no logging bufferedenable secret 5 XXXXXXXXXenable password 7 XXXXXXXXXX!aaa new-model!!aaa authentication login default localaaa authorization exec default local !!aaa session-id commonno ip dhcp use vrf connectedip dhcp excluded-address 10.0.0.1 10.0.0.99ip dhcp excluded-address 10.0.0.250 10.0.0.254!ip dhcp pool Internal-net import all network 10.0.0.0 255.255.255.0 default-router 10.0.0.254 domain-name XXXXXXXXXX dns-server 199.X.X.X 199.X.X.X lease 4!!ip cefip inspect name MYFW tcpip inspect name MYFW udpno ip domain lookupip domain name XXXXXXXXXX!!!!!username XXXXX privilege 15 password 7 XXXXXXXXXX!! !crypto isakmp policy 1 authentication pre-sharecrypto isakmp key XXXXX address 0.0.0.0 0.0.0.0!!crypto ipsec transform-set 3DES-SHA esp-3des esp-sha-hmac crypto ipsec df-bit clear!crypto ipsec profile vpnprof set transform-set 3DES-SHA !!bridge irb!!!interface Tunnel0 ip address 10.10.10.1 255.255.255.0 no ip redirects ip mtu 1350 ip nhrp authentication donttell ip nhrp map multicast
I am attempting to send net and IPTV multicast to an Entone STB. This STB has some OTT features such as Vudu that need internet access. The DHCP address that we receive from our ISP strictly sends multicast streams to the STB.The first challenge is allowing DHCP options to pass through to the STB.Then I need to figure out a way to pass both the net and multicast to the STB.
I'm running a cisco 891 with ios Version 15.2(4)M3 ,now I have a dialer 0 interface with fast0 and 1 as well, all is working fine.now I just read about the new sh int 'INT' history feature but when I do it I get nothing.. not a graph or anything I get just nothing as if I just hit enter.anything I need to do to enable the feature?,if I do a sho proc cpu history that works just fine but not the sh int XYZ history commands
I have cisco 3560G with C3560 Software (C3560-IPSERVICESK9-M), Version 12.2(53)SE1 Image. I want to configure it for EEM feature so that when my Gig 0/7 port goes on it will automatically shutdown the port Gig 0/1.
I'm a bit confused about new NAT functionality in Ver 8.4(2). I've gone through all the documentation as well as different blogs but still not clear about the various things.One of these is NAT-CONTROL. I understand that this has now been removed. Does this means that traffic traversing the ASA doesn't need any NAT'ing commands unless specifically required by the administrator? In other words by default traffic is allowed through the firewall without any NAT'ing.
My Second Query
I've ASA5520 running ver 8.4(2). For inside interface, I've created 13 x sub-interfaces under Gi0/1. All have same security level i.e. 100. What I want to achieve is that:Traffic from these sub-interfaces should be NATTed to outside interface when going to internetBut, intra sub-interface traffic should be allowed without NAT'ing. I'm using RFC1918 on both sides i.e. source / destination The first point is not a problem it's working, however. I'm struggling with the second point. On ver 8.2, it wasn't a problem, I used NAT 0 with access-list permitting RFC1918 addresses as source and destination.
My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
I've a new Dlink DIR-632. All ports snif from outside are answering stealth by default. And the port forwarding feature works good.The problem is that I would like to allow a trusted net IP to reach my computer, whatever the request may be (whatever tcp/udp and on any ports). A kind of DMZ just for a precise IP. I tried the inbound filter feature. I've choosen allow, and I've put the remote IP start and end the same IP. It has been added correctly to the list. However, this IP still doesn't seem to be able to access to my computer on any port unless it tries on an already forwarded port.
I've looked in many places but cannot see how or if it is possible to configure a phone, in CUCM to have a feature ring instead of the normal ring.In CUCME you go into the ephone x configuration mode, and assign the DN to the phone with the button xfx command. What this gives you is a slightly different ring tone when a call comes through. If I am not mistaken it is the same ringtone they use on the show "24".Is there a way to do this "feature" with CUCM?
We are currently installing RV-042 V3 Dual WAN VPN Routers for a Customer with an HQ Office & 3 Branch Offices. The Customer recently requested to use the WEB Filter feature available in the RV-042 V3 Router to do the followng : - " Block all the HTTP Traffic Except for the company Website " We tried all the Combinations between " Access Rules " & " Content Filtering " available under the " Firewall " but we always reach the result that either to Allow ALL HTTP Tarffic to All Websites or to Block ALL HTTP Traffic.
how to Block all HTTP Traffic except for certain URL ( Using the URL Name NOT the IP Address ).
We have 6500 chassises in our set up. But using CWLMS 4.0 , we are unable to manage VSS feature of 6500.Also User tracking for Nexus 7K Switches subnets are not working.
I would like to use the ip address-helper feature of my 3560 switch to point 10.1.0.0/24 to my Windows DHCP Server on 10.0.0.0/24 and I am unsure how to go about doing this.
Should we active IPS feature in ASA 5500-x by useing license?in the 5500-x ordering guide:IPS is only sold as ASA-IPS combo SKUs i.e., one cannot add IPS service as an option on top of ASA SKU. For example, if IPS service is desired on ASA 5515-X appliance, the relevant SKU is ASA5515-IPS-K8 or ASA5515-IPS-K9.But my customer has actived it by using the ASA5525-IPS-SSP on ASA5525-K9.
I have a remote site that has an AP running in H-REAP mode which connects over our MPLS cloud to a WLC, which has one interface on the "inside" network and one on our DMZ. The remote AP in H-REAP mode currently only runs our Guest SSID, but now I need to established an isolated VLAN.
Two of the hosts on this isolated VLAN, which is need to support some conference room devices, need to run on wireless and communicate with two devices on the same VLAN that are hard-wired to the switch.
Getting the wireless devices to connect remotely is easy enough by setting up an SSID that uses an IP subnet which one of the WLC's interfaces actually connects to...but can I do that for a completely remote IP subnet (i.e. one that the WLC does NOT physically connect to?). I'm not sure and I'm wondering whether that's the purpose of the "Remote LAN" feature...which is a very new feature.
I have recently purchased 2 x 1941 routers with 2 L-SL-19-SEC-K9= and 2 L-FL-SSLVPN10-K9= licenses. I've installed the licenses through Cisco Configuration Pro ver 2.5 and installation did not generate any errors. After saving config and reloading the device, on the License dashboard, the deploy status for the SSL VPN is "Not deployed" and I have no way of deploying it. The state also says "Active, Not in use". I have tried reinstalling the license via command line but get error "license duplicate - already installed" suggesting the installation was OK. The sec license deployed without any issues. Is there any way to manually deploy this SSL_VPN license?
i am going to implement a ASA5505 in one of my offices. I would like to use web filtering feature on it. Will it cause any performance degradation in ASA? will it utilized more memory?
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
