I've inherited a 7206VXR router and it takes very long to boot. It outputs READonly ROMMON initialized to the console and 14 minutes later it continues the boot process. After 17+ minutes the boot is complete with the correct full image. The processing engine I have is the NPE-G1 and I'm looking for an upgradeable ROMMON image or a reason why the boot is taking this long.
View 1 Replies
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedMay I know why my 2960S-48TS-L takes 10 minutes to boot and start, some just take 1 minute, but one of them take up to 10 minutes, but after that it works fine, why?
View 2 Replies View RelatedI installed a tp link extender to boost wifi at home (2 storey) and since then I have noticed that upstairs where the router is installed the signal is weaker than downstairs where the extender is located.
View 2 Replies View RelatedMy Cisco 3900 router is not taking the no auto summary command?
View 5 Replies View RelatedThe issue is occuring on our local LAN where my ARP requests are being modified after a period of time by the router for one host. I'm finding that the host will work fine with the correct MAC IP pairing for a period of time and then about 15-30 minutes later, the arp table is changing so the associated mac/IP address is now the mac address of the router interface.
The FastEthernet 0/1 port has no ip proxy-arp enabled and is set with ip nat inside.This only started happening after restarting the router, however the running config was saved as the startup config prior to the restart.I've tried hard-coding the entry with the command arp 10.15.4.190 c82a.1459.0579 ARPA however that is not working as expected.
The device is an 1841 ISR with the advanced IP Services bundle loaded. Is there some way that the router is viewing my host (provides DNS, Directory Services) as a intrustion attempt and somehow rejecting the packets?
I have been using a TP-Link WR1043-ND for a while now. It is configured as a dumb switch with DHCP disabled. Every other day or so, the device stops taking connections and I cannot access via the IP address. A simple power toggle resets everything immediately. Through this, the LAN connected devices never lose connectivity, I simply am not able to connect wirelessly or access the router via web browser.The only device I connect to the wifi is my phone, so it may actually be more frequently and I do not notice due to my low utilization (and I have 3G so I don't always notice right away if I'm connected). I have a WDTV Live SMP connected to one of the LAN ports and that functions non-stop regardless of the wifi. When the wifi is "down", my phone can see the network and attempts to connect. Sometimes it times out, other times I am repeatedly prompted that the password is incorrect, even though I am POSITIVE that I am entering it correctly. Once I toggle power on the router, the phone connects fine with the stored password.
I have updated to the latest firmware (about a month or so ago): Version: 3.13.12 Build 120405 Rel.33996n My hardware version is: WR1043ND v1 00000000 The router is connected (via LAN port 1) to a wall drop. My upstairs roomate maintains the gig switch and modem, as well as handling the network admin. I simply am using the router as a switch to provide extra ports and broadcast the network over wifi in my apartment.All that said: I need troubleshooting this router and it's configuration before I consider buying a more expensive replacement (and if I go this route, I might add a small switch as well to give me more than 4 LAN ports to work with). I am also considering flashing to DD-WRT before replacing as well to see if that makes a difference in reliability and uptime.
determine whether I have QoS properly setup on my router, and why the rules do not appear to be taking effect.ISSUE We have a couple of laptops, smartphones, and a Wii on our home network. One device, my roommate's laptop, is a real bandwidth hog. It's connected (via internet, not VPN) to a work server and is frequently downloading and syncing large datafiles and media files.Unfortunately, when that laptop is downloading the other devices either cannot connect to the internet without timing out, or is VERY slow, for example pulling up websites like google.com. When that laptop is offline, everything works fine. It seemed like enabling QoS would resolve our problem.\
SETUPLinksys E1000, latest firmware (v2.1.02), using WPA2-Personal security.
We first tried enabling QoS and setting the MAC address of the downloading laptop to "low" priority and all others to "medium". No luck - the downloading laptop still seems to be hoarding the bandwidth.We also tried adding the download application to the list and setting the port to "low". Still no luck.We added a new application called "web" and set port 80-81 to "high", but that didn't work.We then disabled WMM support. No dice. The other devices still can't connect while my roommatte's laptop is syncing.We've fiddled around with the settings a bit, but no matter what, it looks like the QoS rules are not being applied.And is it acceptable to have multiple categories (MAC and application) in the QoS rules?
am use router Cisco 7206VXR (NPE-G2) ram 1G now am enable bgp routing full route aboute 400K record , ospf routing maximum traffic throughput is 400 Mbps but the cpu utilize is 80%
View 3 Replies View RelatedI work for a non-profit agency and a donor gave us a generous donation of used Cisco equipment. One of the items is a SM-VAM2+. We tried it in a 7206VXR chassis with a NPE-G2 running 12.4(24)T6 and the router keeps barking that the SM-VAM2+ is not supported in the chassis. We have done searches on the Cisco web site and Google and there is no information regarding the SM-VAM2+ at all (all of the references are for the SA-VAM2+).
The question is if the SM-VAM2+ is supported on the 7206VXR with another version of IOS or what router supports the SM-VAM2+?
we have a 7206vxr router with pa-pos-2oc3 and SFP-OC3-IR1-C. Our provider wants us to check transmitted and received power on the SFP.
I already looked around and know theres no way to check or adjust transmit power and saw its -15 to -8dbm on the datasheet.
Is there a way to check received power?
IOS version
7200 Software (C7200P-ADVENTERPRISEK9-M), Version 12.4(24)T3
I have a setup where a router learns a subnet from both EIGRP process and a BGP process (EBGP peer). In the network's normal state, the EBGP path is preffered path (Primary Path). When the route to the subnet is lost in EBGP, then the router will install the EIGRP learn route into the routing table and use that as its path to get to subnet now (Backup path). This works as expected.
The problem is when the EBGP learn route comes back, the Router still holds on the EIGRP learned route in its routing table. I would think that since the Admin Distance (AD) of EIGRP (90) is higher then the EBGP AD (20) that once the EBGP route is learned again, that it would re-install itself back into the routing table (replacing the EIGRP learned route). But this is not happening.
Im not sure what Im missing here since I thought AD was highest considered attribute the routing table consider when install a route learned from 2 routing process.
The setup Im running is an Cisco 7206VXR (NPE-G2) processor (revision A) running IOS c7200p-spservicesk9-mz.124-15.T12.bin.
I want upgrade IOS on my 7206VXR from 12.4(12c) to 15.1(4)M5 , but the CF card only 64M.
-NAME: "disk2", DESCR: "64MB Compact Flash Disk for NPE-G1"
-Router#show bootvar
BOOT variable = disk2:c7200-jk9s-mz.124-12c.bin,15.1(4)M5 is almost 40M. So there is not enough space.I want to ask is it ok if I upgrade with normal precedure , With the command " copy tftp: disk2: " ?Does the router will automatically delete the older IOS first and then copy into the new one ? Or Is there something I should pay attention first ?
I've been experiencing problems with internet speeds at my church and my home. They both have security keys, but many people use it. I was wondering - Is there a free tool to monitor who/which device is taking up all of the bandwidth? Something that kind of points out, "Hey, this guy is really slowing you down". Possibly even (But not necessarily) kill their connection?
View 1 Replies View RelatedI have a Cisco 876 router, I need to connect ethernet WAN link, While configuring IP address am getting below error.
yourname(config)#int f0yourname(config-if)#ip addres 172.30.1.0 1. 255.255.255.0
% IP addresses may not be configured on L2 links.
Mobile devices are saturating our medium sized enterprise network. Examples of these devices are iPhones, iPads, Kindles, Droids, etc When a device is authenticated on our APMobile wireless network and downloads updates, email, or music our Network bandwidth is consumed. Services/Applications are no longer available, such as VoIP. Basically, this is an internal DoS.I have done some research and an example of this problem is an ARP Storm but currently clients obtain IP addresses form our DHCP server, which acts as a proxy for the clients and if effective against deliberate attempts to craft packets that create ARP Storm. In addition we configured the WLC to disable ARPunicast processing via the CLI.The following link is from Cisco's site. It is the ARPstorm that we originally thought was the cause but after more researching we found it wasn't this exact issue - http:[url]....why iPhones frequently take down our network? Could this be a configuration issue with our firewall (Cisco ASA 5520 running version 8.4(2))?
View 1 Replies View RelatedWe've recently upgraded our switches from 10/100 over to FOUR Dell 2848 (GB Managed switches) and using one as a director (fiber uplink).We are all on GB networks now and we've been running into issues tracking down what's hogging up most of our bandwidth (local area network) throughout our company.We need to track down which machines are copying data to servers and vise versa.
View 1 Replies View RelatedIt is good at times but usually it gets slow and web pages come up with "The web page is taking too long to respond". When I run Diagnose, sometimes I get the computer is correctly configured, but something is wrong with the DNS server (I dont know what that is). I have a NetGear CGD24G Wireless Router that was supplied by Charter when I got internet from them again. I also run Windows 7.
View 12 Replies View RelatedMy old Actiontec M1000 modem recently died and my HP nc6120 with windows XP can not connect to the wireless network through the new Actiontec C1000A model.It connected wirelessly through the old M1000 moden. Window icons on the screen indicate no wireless network is detected. When I view the available networks and log in to the assigned network with its password, it looks like it is trying to connect but does not. It will connect through the ethernet link-up. I don't have any other wireless devices to connect to the network. I have updated the drivers for the wireless card through HP. I have taken the HP nc6120 to the Geek Squad and the wireless card connects with their network. I seem to have a compatibility problem with the old HP with its XP windows operating software and the new modem system. I have tried to reset the ip addresses, but this has had no effect. However, I do have purchased AVG protection software operating on the system, which I am not sure how to shut off. Is this a problem with a too advanced modem for an old style HP with an XP operating system? Is there a modem that I can downgrade to if it is? [code]
View 3 Replies View RelatedMy Multi-media tab is not taking my wireless password? I have a d'link DIR-601; I reset the password using the web interface, but no matter what I try it doesnt link to my tab.What am I doing wrong ?
View 1 Replies View RelatedPast couple of weeks trying to connect to some websites. It is only SOME, not all websites. It will either say that it is taking too long to connect or that the website is experiencing problems. I have no idea where to start as i am pretty clueless when it comes to configuring/repairing network related issues.
View 3 Replies View RelatedSo I have a current port-channel between two 6ks that I need to upgrade. There's too much traffic and the port buffers on the SUP7203B sort of suck. Microbursts are causing overruns like mad. Im going to move the 2x1gig port-channel to a 6724 and make it a 3x1gig port-channel. The switches carry production traffic across the link to the tune of about 400 meg during the lowest load time. Initially, I thought that I couldn't move the port channel without temporarily taking down the link but I think I have a workable solution now. Has anyone done this successfully before? Im curious what others have done. Also, to make matters worse, the existing port-channel is 'mode on' and I want to migrate to 'mode active' in the new channel
View 7 Replies View RelatedUpgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail. How do I take the incoming traps (Crit and Warning) and send an e-mail alarm. I'll plan to control what to trap on at the Cisco Equipment.
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS. Now I want take that trap and forward via an email.
I have been reading the admin documentation on "Notification and Action Setting". I see how to take the Cisco LMS created trap and email alarm. (In this case I need a specific trap that LMS did not have.) I see how to take Cisco Traps and resend them to other NMS.
I work on a college campus that has thousands of students a day accessing our wireless network. We have broadcast SSID that the students use to connect to the internet. The students usually have more than one WiFi enable device on them and their laptops and phones both take an IP address, but they are only using the laptop to authenticate while the phone is associted, but not authenticated. In the meantime, I have several thousand IPs being used by their phones/iPods etc. Is there a way to revoke the DHCP lease if the client does not authenticate within a specified time frame (i.e. 10 minutes)?
View 3 Replies View RelatedI'm in the throes of configuring my 5520 to supply different group policies based on LDAP group membership. I'm finding that no matter what I do only the default group is applied. I'm sure it'll be a simple fix - but I just can't see it. [code]
View 4 Replies View RelatedI have removed all port forwarding and enabled DMZ? I made sure the DMZ IP matches my internal IP. DMZ still not taking effect. One thing I noticed is that when I visited [URL] it showed a different IP then what was assigned to my router itself.
Modem > Linksys Wireless > Computer
Should the Linksys Wireless be in gateway or router mode?
i back up my very important server 2008 r2 data over a vpn to another computerall together its just under 5GB...it used to take 5 to 7 hoursnow the same data is taking 14 to 24hours...why would this be?im using netgear vfs338 vpn firewalls at each end
View 12 Replies View RelatedI have a Dell laptop running Windows 7. The problem is that every single time I try to connect to any wireless network, I get a message that says "Connecting to the network is taking longer than usual."The network almost always connects eventually (about 2 minutes), and once connected there doesn't seem to be any other problem.This has been going on for about 2.5 months. It began shortly after I restored the laptop to factory default.
View 11 Replies View RelatedI have a Cisco 7206VXR with NPE-400. The IOS version is 12.4(24)T3. I installed a SA-VAM in the router in slot 6 but getting the following on the console.
AP-Pune-RT#Feb 23 11:16:34.484: %PA-3-NOTSUPPORTED: PA in slot6 (Unknown (type 650)) is not supported on this chassisFeb 23 11:16:34.484: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:34.584: %PA-2-PABRIDGE: Failed to config bridge for PA 6Feb 23 11:16:35.384: %PA-4-IMPROPER_REMOVAL: Improper removal for slot 6.Feb 23 11:16:35.384: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:35.468: %CRYPTO-4-PKT_REPLAY_ERR: decrypt: replay check failed connection id=975, sequence number=677864
Is the SA-VAM not supported in the Router 7206VXR?
I have an HP Pavilion wireless laptop with windows vista and a gateway desktop, windows XP Home edition and every thing worked ok untill I got a virus on my desktop Since then I've formated the hard disks and reloaded the opering systems, but I don't know how to get the laptop working wirelessly without taking the motorola modem and connecting it directly to the laptop, I have a D-Link DIR-615 router.
View 4 Replies View RelatedI am taking only undersize errors on catalyst 3750 trunk interface (attached some outputs)...the other end is a 4500 switch and the interface is clean..can this be related to any bug ? this is my root port and often leading to trouble sometimes STP BPDUs transportation are affected..
View 4 Replies View RelatedHow many routes support 7206VXR with NPE-G2?
View 2 Replies View Related
