Cisco Switching/Routing :: 7206VXR Does Router Will Automatically Delete Older IOS Then Copy New One
Jan 10, 2013
I want upgrade IOS on my 7206VXR from 12.4(12c) to 15.1(4)M5 , but the CF card only 64M.
-NAME: "disk2", DESCR: "64MB Compact Flash Disk for NPE-G1"
-Router#show bootvar
BOOT variable = disk2:c7200-jk9s-mz.124-12c.bin,15.1(4)M5 is almost 40M. So there is not enough space.I want to ask is it ok if I upgrade with normal precedure , With the command " copy tftp: disk2: " ?Does the router will automatically delete the older IOS first and then copy into the new one ? Or Is there something I should pay attention first ?
View 3 Replies
ADVERTISEMENT
Jan 10, 2012
I am using multiple cisco 2811, 3745 routers and 2950,3550 switches if I need to copy running configuration I have to go to each device and say copy run tftp: <address> Is here any way that automatically by schedule one a week or a month configuration copy from all devices to tftp server?
View 2 Replies
View Related
Nov 23, 2012
On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies
View Related
Jan 4, 2012
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies
View Related
Feb 8, 2012
I do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
View 1 Replies
View Related
Mar 19, 2013
Cpu always hitting 70% to 80 % and interrrupt traffic is 70%. Want to know the root cause for this issue.
CPU utilization for five seconds: 73%/65%; one minute: 71%; five minutes: 67%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 8 59 135 0.00% 0.00% 0.00% 0 Chunk Manager
2 58864 3290773 17 0.00% 0.00% 0.00% 0 Load Meter
3 1784 238001 7 0.07% 0.01% 0.00% 2 Virtual Exec
[code]....
View 1 Replies
View Related
Mar 6, 2013
I am in the process of swapping out an older 24 port Cisco catalyst 3525 POE switch running IOS 12.0(5) with a 48 port POE catalyst 3560 running ios 12.2(50)The trunk port on the older switch (that currently works) is in port Gig0/1 with as basic of a trunk config as you might find.
In the newer switch I have a 1000BaseSX SFP min gbic with a SC-LC fiber cable attached (8.3/125 – 15 meter.When I make the connections, I get no lights… no connection.
View 7 Replies
View Related
Jan 22, 2008
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies
View Related
Jan 13, 2012
I have a number of existing 4506 chassis type switches (the older non -E version) that I would like to roll out IP phones to. Instead of replacing the entire chassis, I would like to just replace the line cards in the switches with WS-X4548-GB-RJ45V. What or how much power supplies should I have in each switch to be able to power the 5 poe line cards (each port per line card will power an ip phone)?
View 6 Replies
View Related
Mar 7, 2012
I am looking into the possibility of using private vlan's for some dmz implementations however I do have what may be some very rudimentary questions. It seems straightforward how to configure the primary/secondary vlan configuration as well as associating them. However in my case I would be looking to configure the PVLAN on a 6500-vss platform acting as the router while all of the hosts which I would desire to have in the isolated vlan would be spread out across a number of older Cisco switches which only support "protected port" setup or Procurve switches all of which I do not have budget to replace with something newer. So in my scenario I would have a 6500 connected by trunk to multiple switches which only support a protected port setup such as a Procurve (top of rack) or a Cisco 2950. As the Procurve or 2950 would not support Private VLAN setup, do I then just configure the secondary vlan to be allowed across the trunk from the 6500, configure that vlan on the Procurve or 2950 (as vtp will not foward the info for the secondary vlan) and assign that vlan to the host port as well as setting it as a protected port and this will communicate just fine across the trunk to the router as well as stopping the protected port in top of rack switch 1 from being able to communicate to a protected port in top of rack 2,3,etc? If the above scenario is what needs to be done, do I just use a regular trunk or do I have to use a PVLAN trunk?
View 2 Replies
View Related
Jul 18, 2012
I have a Cisco 7206VXR running 12.4(24)T3 IOS. It is configured with WCCPv2 using L2 mask redirection. I am using service groups and associated extended ACLs to select which subnets I want to redirect port 80 traffic from.
It is working fine for the subnet 192.168.1.0/24....
int gi0/2
ip wccp 10 redirect in
ip address 192.168.1.99 255.255.255.0
... however, there is OSPF running between the router and a Mikrotik device directly connected to this interface. The gateway addresses for all the client subnets are on the Mikrotik. Traffic from other subnets, e.g. 192.168.2.0/24, 192.168.3.0/24 come in on this interface and I want to redirect those too. But it appears that the redirection doesn't work for those subnets (I don't see any hits on the relevant ACL for any subnet except 192.168.1.0/24).
It seems like the router only wants to redirect traffic for subnets that it has an IP address in itself. Admittedly, all of the example configs i've found on cisco.com are for redirecting traffic from directly connected subnets but I can't find anything that denies thie possibility of redirecting any traffic that comes in on a given interface.
The question is, is this how WCCPv2 redirection works? i.e., the router must have an IP address in the subnet to be redirected?
View 1 Replies
View Related
Mar 20, 2013
I'm configuring a new 2911 running c2900-universalk9-mz.SPA.151-4.M4. In the config by default is "line 2" its not a vty, aux or console line and I can't remove it.
View 1 Replies
View Related
Dec 5, 2011
Is there any way to check if this VLAN is used by somedevice?
Cisco3560#sh ip int b
Vlan55 unassigned YES NVRAM administratively down down
Cisco3560#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
55 Print active Fa0/5, Fa0/6, Fa0/7, Fa0/8
View 18 Replies
View Related
May 2, 2013
how to copy a cisco ios image from a 3750 to my pc so that i can use it to upgrade a switch on my desk.
View 3 Replies
View Related
Jan 4, 2012
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
View 5 Replies
View Related
Feb 13, 2013
I have 2 Chassis 6506-E with sup 720. one of them work properly(Switch1) but another(Switc2) not boot form bootdisk and go to ROMMON mode. I Captured IOS from Switch1 with tftp but I cant Copy this image to switch 2 with tftp.
View 4 Replies
View Related
Feb 27, 2013
It seems I have seen this before (and even done it once a few years ago).. but it has been a while. I have a stack with a Cisco 3750 stack that I have to replace a member.The replacement switch is a 3750X.
I think I have to upgrade the IOS of the older switch to be the same as the 3750X.
Current switch: WS-C3750G-48TS 12.2(46)SE
TO BE ADDED WS-c3570X-48 15.0 (1)SE2
It seems to me there was a way to upgrade the older switch IOS from the newer switch or downgrade the newer switch with the older IOS.I dont have the Cisco account to download updated IOSs.
View 9 Replies
View Related
Sep 1, 2012
I want to delete the first file c2600-i-mz.122-5d in the flash. Not only delete but also reclaim the memory held by deleted file.I followed a link and i ended up with the c2600-i-mz.122-5d marked as deleted in the flash but the memory was not reclaimed.When I restarted the router, it went to ROMMON mode. This is my understanding when router tried to boot from the flash, It tried to load the first file in the flash. Since the file was marked as deleted therefore Router went to ROMMON mode.Now my question is how could I delete the first file and reclaim the memory on 2600 router?
View 8 Replies
View Related
Aug 7, 2012
I own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies
View Related
Jul 1, 2012
Working on a C4948-10g switch. Trying to reset switch to factory settings. I have ran the Switch#>wr erase, command but the vlan's are still in the config. If you do a show vlan it still shows all the vlan text. I have tried the Switch#>delete vlan.dat, doesn't work. Tried Switch#>delete nvram:vlan.dat, doesn't work. Tried Switch#>erase startup-config, doesn't work. How can I get rid of the vlan's?
View 7 Replies
View Related
Apr 16, 2012
I am trying to configure redundancy with SSO and I need to get the same IOS on both supervisors. My issue is that I get an error when I try to copy the IOS from either the sup-bootdisk or the disk0 to the slavesupbootdisk. The Error is Invalid argument.
I have tried also to tftp to the slavesupbootdisk and get the same result.
View 5 Replies
View Related
Jun 12, 2012
I want to copy a file from one ASR1001 and copy it to another. I ntried using tftp 32 but this is not going to work as the image is 315 MB.
how to copy an image from one router directly to another router's flash, if possible?
View 5 Replies
View Related
Jul 9, 2012
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies
View Related
Oct 11, 2012
I know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
View 3 Replies
View Related
Apr 16, 2013
i have a few 3550's at the moment and when i use the delete /force /recursive flash:html command it just throws back "permission denied" this seems pretty common on the 3550 but i have never had an issue on the 2950, 3550, 2960, 3560 just the 3550.
Can any give me the command for recursive deleting on the 3550 in the console i.e. hyper terminal?
View 6 Replies
View Related
Jan 24, 2012
I have a 3550 switch that was replaced at a remote site with no IOS. This is a switch not a router so tftpdnld does not work.
[Code]...
The problem is the switches interface never comes up so try to connect to the tftp server. I read on google it can't be done on a switch to copy from tftp to flash in rommon mode on a switch and to use XMODEM. My problem is I do not have access to it, I ssh into a 3640 which is an access server for all devices and that is how I have console to it, how to use XMODEM over ssh.
But I'm fairly certain that there has to be a way to just copy it from tftp? I have a 3550 local and when I put it in rommon mode it stops the port check at port, port 1 goes from green when you plug it in to off then port 2 changes to amber and the rest green. So just by the look of this I would believe tftp would work; you just need to use port 1.
View 1 Replies
View Related
Feb 20, 2012
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
View 14 Replies
View Related
Dec 7, 2011
I am trying to configure a switch that was given to me. They don't know the password to anything. I have already tried to recover it. The problem is, the switch doesn't load flash, or will copy flash from xmodem either. It also doesnt load the helper or boot. It is user mode and lets me do nothing. It doesnt let me use the enable command to get into it. I would like to start the config from scratch. Its a 3500xl switch, 24 ports. I dont know what to do with it. I am trying to study for my CCENT Exam and would like a switch that worked.
View 8 Replies
View Related
Oct 5, 2010
I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
View 25 Replies
View Related
Feb 22, 2012
I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
View 5 Replies
View Related
Nov 2, 2010
i have major problem with two new Small Business 300 Series switches.Everytime i try to save the running config i get a GUI error message: "Another copy process is active, please try again later."It's also not possible to re-flash the firmware because the GUI stops responding.I have also tried to do this via console access and this produces a "the copy utility is occupied by another user" error message.-> so this is not a browser based problem.My first thought was that the switch (SG 300-28) is faulty so i unpacked the next new one (SF 300)and got the same error messages!Then i had a 2 hour webex support session with the Cisco Small Business Support and they did not found a reason for this behavior.Both switches are working normally, you can configure them, but after a reboot they are back to factory default again There is no possibilty for copy running config to startup config and it's also not possible to flash the firmware.(Web GUI & Console). tell me if this is a fundamental problem of the 300 Series?
View 6 Replies
View Related
Apr 16, 2012
Two computers (XP and Win7) connected on office LAN, cisco 2960, not same switches, but all in the same rack, and link togeter, same IP subnet, tried to copy some kind of 26G files from one to another, using Windows share folders, and it showed need 23 hours to finish the copying.It's not the first time, actually we always experienced very slow speed when copying files on Windows share folders. Did not see any particualler message on the switch. ports are all full/100m.
View 9 Replies
View Related
Nov 25, 2012
I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
View 4 Replies
View Related
