Cisco Switching/Routing :: How To Delete Vlan Configuration On C4948-10g
Jul 1, 2012
Working on a C4948-10g switch. Trying to reset switch to factory settings. I have ran the Switch#>wr erase, command but the vlan's are still in the config. If you do a show vlan it still shows all the vlan text. I have tried the Switch#>delete vlan.dat, doesn't work. Tried Switch#>delete nvram:vlan.dat, doesn't work. Tried Switch#>erase startup-config, doesn't work. How can I get rid of the vlan's?
View 7 Replies
ADVERTISEMENT
Dec 5, 2011
Is there any way to check if this VLAN is used by somedevice?
Cisco3560#sh ip int b
Vlan55 unassigned YES NVRAM administratively down down
Cisco3560#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
55 Print active Fa0/5, Fa0/6, Fa0/7, Fa0/8
View 18 Replies
View Related
Apr 29, 2013
I'm using "WS-C4948(12.2(54)SG)+PWR-C49-300AC/2". The following message are logged in the system log, but it was to check the status with the show command and status LED, but there was no abnormality. I thought the power supply has failed, but I seem different.
040861: Apr 27 07:00:50: %C4K_IOSMODPORTMAN-4-POWERSUPPLYBAD: Power supply 1 has failed or been turned off
040862: Apr 27 07:00:50: %C4K_IOSMODPORTMAN-4-POWERSUPPLYFANBAD: Fan of power supply 1 has failed
I checked.>> #show environment alarm no alarm
#show environment status power supply
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C49-300AC AC 300W good good n.a.
PS2 PWR-C49-300AC AC 300W good good n.a.
All Status LEDs are green.
View 5 Replies
View Related
Apr 3, 2013
I encountered an issue while trying to boot Catalys WS-C4948-S switch. I power on the switch and I'm able to see the boot messages thourgh serial console cable. But it gets stuck at line "Image text-base: 0x1000000, data-base: ..... ". Also I can enter into rommon mode. I tried to use different kinds of IOS images, tried to boot from tftp but with no luck, the issue is the same.
There are no erros on the screen, it just gets stuck when it enters into IOS, so I don't see the IOS prompt.
View 5 Replies
View Related
Feb 25, 2013
I am running (cat4500-ENTSERVICES-M), Version 12.2(53)SG2 on the switch. I have a scenario where I have 3 end user equipments connected to a Cisco 4948 L3 switch. At the switch end port 1/46, 1/47, 1/48 are the terminating points for these 3 devices . I have added these three ports to VLAN140 (switch port access vlan140 on the gig interfaces).
The device connected to 1/46 is the one I'm testing some signalling features on. My requirement is to have intermittent packet drop on this interface so that my signalling associations would go down now and then. I'm trying to simulate a real-time network congestion/latency/packet drop in a simple manner.
I do not want to shut/no shut the 1/46 intf to cause this. Some way to achieve intermittent packet drop on this gig1/46 intf ?
View 3 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
May 2, 2011
I have a headquarters office that has recently bought a new voice system.
We have a site to site connection from the head office to 3 remote offices. All have ASA5505 firewall.
I have created 2 interface on the ASA5505: 1: inside with vlan1 and switch port port12: voice with vlan100 and switch port port2
Port1 on the asa goes to port 23 on the switch for vlan data
Port2 on the asa goes to port 24 on the switch for vlan voice
Port23 is member of vlan1 data
I added vlan100 to port 24 but by default vlan1 is member and i can't remove it. Its greyed out
All ports on the switch are member of vlan1 and vlan 100 because the port on the switch goes to the phone and from the phone there is a port that goes to the PC. Phones are getting addresses, and PC as well.
I am having a kind of loop because there is 2 exit for vlan1 (port 23 and 24) and that's slowing down my system and sometime i loose the connectivity to my servers.
When i do a show arp on my asa, i do see that some IP are beeing learned on the wrong interface. some PC addresses 192... are on the voice and some voice IP 10.10... are on the inside.
I am pretty sure that the problem comes from my switch configuration.
View 7 Replies
View Related
May 28, 2012
I have a hybrid kind of network. I want to create create two VLANs on Cisco SGE2010 so that these two VLANs should not talk each other but at the same time they are able to talk Domain controllers, DHCP and other servers which are on other switches.I am able to create two separate VLANs but they stop talking with other servers(DC, DHCP, etc) which are on another switch.
View 7 Replies
View Related
Sep 15, 2012
I have 2 locations, at a distance of 600KM.These two locations are well connected by Point to Point L2 VLAN with a speed of 2 MBPS and supported by CISCO 3560G switches.Location A has a VLAN to communicate to the other VLAN at Location B. Location B has also got 3 VLANS which are inter connected with Location A.Now the hardware in one of VLANs in Location B has moved to Location A for obvious reasons.
For further refernce am giving the VLAN IP address here....
Location A
VLAN1 for communicatng to Location B
IP Range 172.20.44.210
Subnet Mask 255.255.255.0
Default Gateway 172.20.44.210
VLAN2 for the desktops in Location A
IP Range 192.193.194.1-255
Subnet Mask 255.255.255.0
Default Gateway 192.193.194.1
[code]....
View 3 Replies
View Related
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Dec 9, 2012
I am seeing an issue that after deleting/recreating one of the VDC in Nexus 7K, VLAN is not been able to be configured within the VDC although it is not actually a reserved VLAN. Could it be anything missing in the license installation? the version of the image is NX-OS 6.1.2
StorageVDC(config)# vlan 100
^
invalid vlans (reserved values) at '^' marker.
View 2 Replies
View Related
Jun 17, 2012
After a abrupt power cylce of 6509 switch, vlan configuration got missing. Switch has not crashed.
View 4 Replies
View Related
Oct 24, 2011
I have got a catalyst cisco 2960G series switch and via this switch I want to creat serveral vlans. I am getting a dhcp IP from a router and I want to setup my own vlan networks.
I plugged in the Ethernet cable that came from the dhcp router to port 16 of the cisco switch and configured the ports 1,2 and 3 for vlan 1, 2 and 3
the dhcp router has given me this IP 192.168.10.158 defautl gateway is : 192.168.10.1
when I plug in a PC to port 1 or 2 of the cisco switch I still receiving the IP from range 192.168.10.* but not from the range that I configured for the vlan 1 or 2.
Below is my startup configuration:
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
[code].....
View 28 Replies
View Related
May 22, 2013
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
View 12 Replies
View Related
Mar 11, 2013
Using Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies
View Related
Apr 29, 2013
I've turned up a new layer 2 WAN link between two data centres and i'm having some trouble trying to logically figure out how things should be configured.As you can see from the diagram i've created, I have the link connected on port 13 on one switch and port 14 on the other. Both ports have an IP address assigned to them and they can both ping each other..
The problem comes when I need to add routes in order to get traffic flowing over the link.I added an IP address to switch 2 on the link interface (port 14) as: 192.168.4.10
I then added an IP address to switch 1 on the link interface (port 13) as:
192.168.1.10
192.168.2.10
When I tried to add 192.168.3.10, it said "192.168.3.0 overlaps with VLAN2626". This would be correct as Vlan 2626 has an IP address of 192.168.3.15.
However, if I remove the IP address from vlan 2626 and add 192.168.3.10 to vlan 2 (the link port VLAN), I would surely lose remote access to the switch. (I'm telnetting into the switch from a machine on vlan 2626).
I started to tinker with this by manually adding a route to a server in each location and seeing if I could get traffic to flow:
On server 1: route add 192.168.4.0 MASK 255.255.255.0 192.168.1.10 METRIC 1
On server 2: route add 192.168.1.0 MASK 255.255.255.0 192.168.4.10 METRIC 1
If I try to tracert 192.168.1.20 from server 2, the first hop is the default gateway instead of 192.168.4.10.
The ultimate goal is to add the static routes to the Layer 3 router/firewall, but before I do that, I need to be sure of what to add to that router (It's a manged firewall from the data centre, so I don't have access to it and I need to raise firewall change requests to get the work done, so want to ensure it's right first time.
View 9 Replies
View Related
Feb 12, 2012
I was unable to configure vlan-based qos on Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXH6, RELEASE SOFTWARE (fc1) Seems to me my configuration is not working. Here is the output of the interface:
sh int G1/6 | i rate
Queueing strategy: fifo
30 second input rate 25231000 bits/sec, 4282 packets/sec
30 second output rate 46940000 bits/sec, 9257 packets/sec
And here is my configuration:
interface Vlan3
ip address 192.168.1.1 255.255.252.0
service-policy input TEST_IN_PMAP
service-policy output TEST_OUT_PMAP
[code]....
Why I can't see matches in ACLs? I've double checked the direction and seems to me it is correct. I can't see matches even I configure something like this:
10 permit ip host 192.168.1.168 any
20 permit ip any host 192.168.1.168
Why my output rate is higher than 30M? Is it bacause there is no matching traffic here in ACLs? I'm absolutely shure that this host with such ip connected to this interface:
#sh arp | i 192.168.1.168
Internet 192.168.1.168 0 feed.beef.f00d ARPA Vlan3
#sh mac address-table | i feed.beef.f00d
* 3 feed.beef.f00d dynamic Yes 0 Gi1/6
View 9 Replies
View Related
Jun 22, 2012
I have on 3750X stack with a few vlan
--------------------------------------------------
vvlansw06# sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/0/6, Gi1/0/10, Gi2/0/5
Gi2/0/6, Gi2/0/37
10 LAN_10 active Gi1/0/16, Gi1/0/17, Gi1/0/19
[code]....
where are the others vlan?
View 3 Replies
View Related
May 19, 2013
In my core Switch,there are 2 v LAN(V LAN 1 & V LAN 2)my switch is Cisco 4948,so be default ip routing is enable in it. My all servers (DHCP,HTTP,HTTPS) are in v LAN 1 & internet is also in v LAN 1.
My requirement is that v LAN 1 user should not communicate with the v LAN 2 and vice versa. But the v LAN 2 users need an access of all servers and internet which is in v LAN 1. How to configure the access-list. I have try on Packet tracer which i have attached.
note:v LAN 2 user should get the IP from dhcp server which is in vlan1.
View 4 Replies
View Related
Mar 6, 2013
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies
View Related
Dec 12, 2012
We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
View 3 Replies
View Related
Jul 5, 2012
I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
View 2 Replies
View Related
Jan 28, 2013
I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17
( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself)
Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2
ip address 172.16.0.30 255.255.255.240
ip helper-address 172.16.0.17
interface Vlan3
ip address 172.16.0.46 255.255.255.240
ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
View 3 Replies
View Related
Apr 12, 2012
provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
View 2 Replies
View Related
Mar 20, 2013
I'm configuring a new 2911 running c2900-universalk9-mz.SPA.151-4.M4. In the config by default is "line 2" its not a vty, aux or console line and I can't remove it.
View 1 Replies
View Related
Sep 1, 2012
I want to delete the first file c2600-i-mz.122-5d in the flash. Not only delete but also reclaim the memory held by deleted file.I followed a link and i ended up with the c2600-i-mz.122-5d marked as deleted in the flash but the memory was not reclaimed.When I restarted the router, it went to ROMMON mode. This is my understanding when router tried to boot from the flash, It tried to load the first file in the flash. Since the file was marked as deleted therefore Router went to ROMMON mode.Now my question is how could I delete the first file and reclaim the memory on 2600 router?
View 8 Replies
View Related
Aug 7, 2012
I own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies
View Related
Jun 5, 2013
I have the new firmware running on my SG500 switch. I've also just finished creating my VLANs. My issue is that I can't delete the old default VLAN .... VLAN 1. More importantly, I can't seem to get DNS to work on the switch.
When I set a DNS server, the VLAN defaults to VLAN 1, and the option is greyed out and can't be changed. Why is it VLAN1? Why is it greyed out? How do I get DNS to work on the switch, for services like Time Servers?
View 7 Replies
View Related
Apr 16, 2013
i have a few 3550's at the moment and when i use the delete /force /recursive flash:html command it just throws back "permission denied" this seems pretty common on the 3550 but i have never had an issue on the 2950, 3550, 2960, 3560 just the 3550.
Can any give me the command for recursive deleting on the 3550 in the console i.e. hyper terminal?
View 6 Replies
View Related
Jan 10, 2013
I want upgrade IOS on my 7206VXR from 12.4(12c) to 15.1(4)M5 , but the CF card only 64M.
-NAME: "disk2", DESCR: "64MB Compact Flash Disk for NPE-G1"
-Router#show bootvar
BOOT variable = disk2:c7200-jk9s-mz.124-12c.bin,15.1(4)M5 is almost 40M. So there is not enough space.I want to ask is it ok if I upgrade with normal precedure , With the command " copy tftp: disk2: " ?Does the router will automatically delete the older IOS first and then copy into the new one ? Or Is there something I should pay attention first ?
View 3 Replies
View Related
Nov 23, 2012
On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies
View Related
Mar 10, 2005
I was given a 510 PIX Ver 6.3(1)to reconfigure but have no information on the existing configuration and need to wipe it clean and start over how can I do this to get back to the factory default settings. I have tried the "monitor>" but I don't know the IP address of the PIX interface.and am not sure how to do the setup for recovering the password.
View 7 Replies
View Related
Feb 6, 2012
We have a pair of ACS 4.1 servers (Windows Server 2003 R2). Let's call them ACS1 and ACS2. We don't want either one of them to proxy to any AAA server, including each other. We're using mostly TACACS authentication.
While troubleshooting a general problem, I'm guessing that one of us did this on ACS1:
pressed the Network Configuration button,saw the Proxy Distribution Tableclicked (Default)moved ACS1 from the AAA Servers column to the Forward To column.
So, essentially, we're telling ACS1 to proxy all requests to itself, which doesn't seem to make sense. I don't know for sure whether it should work when configured to "self proxy," but in that state, it does not authenticate anyone and gives merely "Internal error" as the reason.
If I change the configuration so that "ACS2" appears in the Forward To column, and I move "ACS1" back to AAA Servers and restart, ACS1 starts responding correctly to TACACS requests. Of course, ACS1 is just proxying all requests to ACS2, so having two servers isn't doing much good.
I cannot simply remove ACS1 from the Forward To column and leave it empty. The interface complains that it can't forward to zero servers. Of course, on ACS2, there are no servers in the Forward To column, since we never touched the Proxy Distribution Table there.
Is there any way to return the Proxy Distribution Table to its default setup, that is, no servers appear in the "Forward To" column?
We're planning to upgrade to version 4.2 very soon, so this question is mostly academic, unless the same problem exists in 4.2.
For full disclosure, I should mention that the problem we were troubleshooting was loss of connectivity to our Windows Domain Controllers from our ACS servers. We had missed adding some exceptions in our firewalls to allow for four new DCs. As far as we can tell from testing, connectivity to the DCs is now fine. The firewall rules group ACS1 and ACS2 together, so connectivity should be the same, and ACS2 authenticates users correctly.
View 2 Replies
View Related
