Cisco Switching/Routing :: 3750X / VLan Missing In Running-configuration?
Jun 22, 2012
I have on 3750X stack with a few vlan
--------------------------------------------------
vvlansw06# sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/0/6, Gi1/0/10, Gi2/0/5
Gi2/0/6, Gi2/0/37
10 LAN_10 active Gi1/0/16, Gi1/0/17, Gi1/0/19
[code]....
where are the others vlan?
View 3 Replies
ADVERTISEMENT
Jun 17, 2012
After a abrupt power cylce of 6509 switch, vlan configuration got missing. Switch has not crashed.
View 4 Replies
View Related
Dec 27, 2012
I have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
View 4 Replies
View Related
Jan 18, 2012
I have one VLAN on a 3750 where I do not see any MAC addresses even though it is in use. This is an unrouted VLAN between a WLC on a port- channel /LAG and an access port to an ASA for guest traffic. When I do a show MAC add I get nothing for VLAN 60 (guest DMZ) but all other VLANs seem to be OK. Spanning tree is not showing TC counters incrementing either.
I also was told when put a port on this VLAN the laptop did not get a DHCP address form the ASA, but the wireless guest clients are working fine. I can see the DHCP leases and ARP entries in the ASA and the ASA ARP in the WLC so some traffic is passing fine. I'm not onsite right now so troubleshooting is all remote which limits some options.
View 4 Replies
View Related
Sep 22, 2011
I recently upgraded my network to have two 3750x core, one interface on the cisco is connecting to a Netgear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
View 2 Replies
View Related
Feb 6, 2013
I have a LIII Switch Cisco 3750x ,with diffrent Vlans , Some users are in Vlan 102 (10.10.2.0) and Some Users are in Vlan1 (10.10.1.0) , now i want to restrict the Vlan102 users to access Vlan1 , i am pasting my configuration below , how to create a access list .
interface Vlan1
ip address 10.10.1.36 255.255.255.0
ip helper-address 10.10.1.36
[Code].....
View 2 Replies
View Related
Mar 19, 2013
I have one issue on Vlan in Cisco 3750X switches , I have 2 Offices , I am sitting at corp OFfice and i have one 3750 ( 10.10.1.36)Switch at my location , in my remote office i have one more switch 3750 ( 10.10.33.1) and i am able to access the both vlan IPS with out any issue , now i have some network components in Vlan33 ( 10.10.33.1) at my remote office . i am able to ping 10.10.33.1 IP from my corp office , but i am not able to ping any network devices in 10.10.33.5 example : 10.10.33.5 is my Cyberoam IP at remote location and i am not able to ping , i have taken a trace route and not able to find the issue as i am not much femilar , ping 10.10.33.5 at remote location devicec
I am giving the Configuration for both locaitons below :
10.10.1.36 - Corp Office 3750 Switch:
sh run
L3-#sh running-config
Building configuration...
[Code].....
View 1 Replies
View Related
Mar 18, 2013
I've got a 3750x stack set up as my core switch (only a small-ish environment) - I'm shortly going to be deploying an enterprise wireless network with Corporate and Guest SSID's. I'm going to be putting all traffic from the Guest SSID in VLAN 244, and don't want it to have access to any of the other VLANs (1 (Legacy Eqpt), 4, 8, 12, 16, 20, 24, 28, 32, 248 & 252).
IP ranges for all the main VLANs are:
1: 10.0.0.x/22
4: 10.0.4.x/22
8: 10.0.8.x/22
12: 10.0.12.x/22
16: 10.0.16.x/22 etc etc (you get the pattern)
I'll probably give Guest traffic (VLAN 248) the IP range 192.168.10.x/22 (not because I NEED that many addresses, but it's easier for everyone to remember/understand if I keep the subnet masks the same all round). However I also have a CCTV VLAN (252) which already has the range 192.168.0.x/24, which some people in other VLANs WILL need access to.
So my question is: What is the syntax for the ACL on my 3750x (IP base - 15.0.2) to prevent traffic from VLAN 244 gaining access to any of my other VLANs. I'm making a broad assumption here that a layer 3 switch is perfectly capable of supporting that function? I need ALL the syntax for setting up ACL's - I've never done it before
My gateway device by the way is 10.0.4.1, and I do have inter-VLAN routing set up on the core switch (obviously).
View 3 Replies
View Related
Oct 7, 2012
I am migrating an existing LAN from 3550 to 3750X-12S. In the existing configuation, I´ve got some trunks with native VLAN <> 1. The native VLAN is also used for user data transport. With IOS 15.0(1)SE3 on 3750X I recognized, that per default behavior PVST is not active for a VLAN defined as native, even if the corresponding trunk is up and trunking. My current workaround is to add a "switchport access vlan" command on the trunk even this one never should become an access port. With this statement only the switch is activating the PVST for the native VLAN. For all other vlans PVST works as exspected. [code]
View 6 Replies
View Related
Jul 19, 2012
We currently have 7 Cisco 3524-XL switches (10-12+ yrs old) which are 10/100. We purchased a handful of Cisco 3750X switches to replace them going with the whole stackwise and redundant power supplies. Our current configuration on the old 3524 switches is that they have hardset all the ports on them to 100MB/FULL since devices would auto-neg to 100/Half. Since we're going from 10/100 to 10/100/1000 switches, I want things to auto-neg as I have heard in the past and experienced that things work better when it auto-neg to gigabit. My upper management is afraid since the old switches wouldn't auto-neg correctly that we should hard set all the ports on the new switches, which would be a nightmare since some ports would be hard set to 100/FULL others to 1000/FULL, etc.. We've tested just about all of our devices at auto with the switches and they've all auto-neg to the correct speed. In short, is Auto-Negotiation the way to go with the newer switches or is it still better practice to hard set your ports?
View 3 Replies
View Related
May 21, 2012
I'm building a new colo presence with a full class C of public IP's. The idea is to connect to our ISP with a 3750x switchstack and they will be providing two ethernet drops that conect directly into two seperate switches on their side with HSRP and BGP at the routing level, so we will just point to their virtual IP (gateway address).I'm not sure how to either segment the public ip block or statically route each ip address and the interaction of vlans/svi with HSRP groups. Just use the switch at layer 2 or handle the internal routing with eigrp or ospf at layer3?
View 2 Replies
View Related
Oct 8, 2012
Has anything changed in the way of defaults for creating a trunk port and spanning-tree between a 3750x and the newer 2960s? I have one of each I just took out of the box and applied my standard switch configuration template but I cannot get my VLANs that are configured on my 3750X to appear on the 2960S. I find nothing that is blocking and everything seems to be forwarding and I am running out of things to check.
View 5 Replies
View Related
Dec 10, 2012
I have a requirement whereby a CCTV system is being installed that will need multicast RTSP configured on the switch network. How this will be achievable on 3750X IP Services switches? if this is not possible then what switch hardware will be needed?
View 2 Replies
View Related
May 15, 2012
I would like to know if there an specific configuration in order to apply QoS configuration in Switches 3750X for Polycoms Phones.I was reviewing the information from Cisco but mostly of them apply only for cisco phones, and just some or basic for non cisco phones.
View 1 Replies
View Related
Jan 28, 2013
when enabling multicasting on layer 3 interfaces the CPU becomes fully utilized , is there any specific configuration should be enabled to reduce this .
Config :
Inetface vlan 100
ip pim sparse-dense
ip igmp version 3
[Code]......
View 1 Replies
View Related
Apr 7, 2013
I am trying to configure a new metro ethernet and have some questions about the configuration. The physical layout is a main office and two remote locations. The remote sites are point-to-point connections to the main office, tagged by the ISP with VLAN 130 and VLAN 140. The connections aggregate into one handoff at the main office, and are plugged into Catalyst 3750-X switches at all three sites.
View 8 Replies
View Related
Mar 26, 2012
Company has implemented a 3750x with older Lexmark Pro print servers on new V lan configuration for printers. Causing print servers to lose connection. Have to reset constantly. Have tried to configure print server ports to full. Also new Nexus 7000. Perfect scenario is network devices.. not there yet.
View 3 Replies
View Related
Jul 6, 2012
I am trying to setup intervlan configuration and stuck on a problem. Here are the details:
1. Switches Catalyst 3750-x (as core switch) and Catalyst 2960S (as access switch)
2. Both switches have VLAN 20 and VLAN 1 on their database and both are active. BTW, after I figure out how to properly configure interVLAN routing the native VLAN 1 will not be used anymore. This is just an initial test.
3. VLAN 20 SVI interface (IP 192.168.20.200) on 3750 is up and can be pinged from catalyst 2960.
4. VLAN 1 SVI interface (IP 192.168.170.200) on 3750 is up and also can be pinged from Catalyst 2960.
5. Catalyst 3670 can ping a client computer (IP 192.168.20.10) connected to Catalyst 2960.
6. IP route enabled on 3750
7. Trunking is enabled on etherchannel connecting both 3750 and 2960
8. Client computer in VLAN 20 (connected to 2960) can ping VLAN 20 SVI interface 192.168.20.200 on switch 3560.But, the client computer in VLAN 20 can not reach any computer in VLAN 1 and vice versa. Strangely, the switches which these computers are connected to can ping each other or any connected client copmuters without any problem as described above.
View 8 Replies
View Related
Jan 14, 2013
I'm working at a company that has several 6509 switches running CatOS. They have two of the 6509's running in vtp server mode and the rest as clients. I set up a new vlan from one of the vtp servers and it propagated out. The problem comes when I try to assign a port on one of the vtp clients to this new vlan. It gives me an error that the switch must be in vtp server mode to add/delete vlans. I'm not trying to add/or delete a vlan just trying to add a port into an existing vlan. I'm hesitant to put the switch in vtp server mode. Is this a CatOS thing or is there a specific command to accomplish this?
View 5 Replies
View Related
Oct 24, 2012
I am installing a several new Cisco VM servers. The VM hosts are losing connectivity when we apply the etherchannel config in the core stack. VMware has stated that the etherchannel load balance needs to be src-dst-ip in order for the etherchannel to work.However, my current stack has 2 etherchannels configured to other switches through out the bldg in network closets. The current load balance configuration is src-mac.My question....when I make the change to src-dst-ip, will my network connectivity go down? I saw there was an older article on this that doesnt provide an answer just a work around. Here is the article. [URL].
View 1 Replies
View Related
Aug 7, 2008
We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1. I've got lots of these switches running the same code that are just fine.
View 8 Replies
View Related
Feb 22, 2013
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies
View Related
Apr 23, 2012
I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies
View Related
Apr 2, 2012
My company is beginning to have a lot of sites were we are stacking 3 to 4 C2960S-48 switche.This is making "show running-config" very very long because of the 4 x 48 interfaces.I can’t find a CLI command that show me the running-config of a ranges of interfaces. If I for example would like to see running-config for switch 3 (interfaces 3/0/1-52)The Show Running-config will show all the interfaces (for the two first swtiche = 104 interfaces), which take a time before I reach to switch 3.I miss a CLI command like: show Running-config switch 3, or module 3, or show running-config interface range x/x/x-x ?I’m well aware of the CLI command show running-config interface x/x/x, but this will only show me one interface.
View 3 Replies
View Related
Oct 14, 2012
I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I would like to convert my CatOS running configs to IOS, and I know there used to be a tool for this.
I have searched around and found many broken links to an old Cisco tool to convert my former configs, is there any way to get this tool today? I have tried over 20 links and not been able to find a working one yet.
View 2 Replies
View Related
Apr 29, 2012
What is the exact command in restoring the running-config on a Nexus 7010. Is it the same command / procedure as the Cisco IOS?
View 3 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
May 2, 2011
I have a headquarters office that has recently bought a new voice system.
We have a site to site connection from the head office to 3 remote offices. All have ASA5505 firewall.
I have created 2 interface on the ASA5505: 1: inside with vlan1 and switch port port12: voice with vlan100 and switch port port2
Port1 on the asa goes to port 23 on the switch for vlan data
Port2 on the asa goes to port 24 on the switch for vlan voice
Port23 is member of vlan1 data
I added vlan100 to port 24 but by default vlan1 is member and i can't remove it. Its greyed out
All ports on the switch are member of vlan1 and vlan 100 because the port on the switch goes to the phone and from the phone there is a port that goes to the PC. Phones are getting addresses, and PC as well.
I am having a kind of loop because there is 2 exit for vlan1 (port 23 and 24) and that's slowing down my system and sometime i loose the connectivity to my servers.
When i do a show arp on my asa, i do see that some IP are beeing learned on the wrong interface. some PC addresses 192... are on the voice and some voice IP 10.10... are on the inside.
I am pretty sure that the problem comes from my switch configuration.
View 7 Replies
View Related
May 28, 2012
I have a hybrid kind of network. I want to create create two VLANs on Cisco SGE2010 so that these two VLANs should not talk each other but at the same time they are able to talk Domain controllers, DHCP and other servers which are on other switches.I am able to create two separate VLANs but they stop talking with other servers(DC, DHCP, etc) which are on another switch.
View 7 Replies
View Related
Sep 15, 2012
I have 2 locations, at a distance of 600KM.These two locations are well connected by Point to Point L2 VLAN with a speed of 2 MBPS and supported by CISCO 3560G switches.Location A has a VLAN to communicate to the other VLAN at Location B. Location B has also got 3 VLANS which are inter connected with Location A.Now the hardware in one of VLANs in Location B has moved to Location A for obvious reasons.
For further refernce am giving the VLAN IP address here....
Location A
VLAN1 for communicatng to Location B
IP Range 172.20.44.210
Subnet Mask 255.255.255.0
Default Gateway 172.20.44.210
VLAN2 for the desktops in Location A
IP Range 192.193.194.1-255
Subnet Mask 255.255.255.0
Default Gateway 192.193.194.1
[code]....
View 3 Replies
View Related
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Dec 9, 2012
I am seeing an issue that after deleting/recreating one of the VDC in Nexus 7K, VLAN is not been able to be configured within the VDC although it is not actually a reserved VLAN. Could it be anything missing in the license installation? the version of the image is NX-OS 6.1.2
StorageVDC(config)# vlan 100
^
invalid vlans (reserved values) at '^' marker.
View 2 Replies
View Related
Oct 24, 2011
I have got a catalyst cisco 2960G series switch and via this switch I want to creat serveral vlans. I am getting a dhcp IP from a router and I want to setup my own vlan networks.
I plugged in the Ethernet cable that came from the dhcp router to port 16 of the cisco switch and configured the ports 1,2 and 3 for vlan 1, 2 and 3
the dhcp router has given me this IP 192.168.10.158 defautl gateway is : 192.168.10.1
when I plug in a PC to port 1 or 2 of the cisco switch I still receiving the IP from range 192.168.10.* but not from the range that I configured for the vlan 1 or 2.
Below is my startup configuration:
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
[code].....
View 28 Replies
View Related
