Cisco Switching/Routing :: High Cpu Utilization On 7206VXR / NPG-1?
Mar 19, 2013
Cpu always hitting 70% to 80 % and interrrupt traffic is 70%. Want to know the root cause for this issue.
CPU utilization for five seconds: 73%/65%; one minute: 71%; five minutes: 67%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 8 59 135 0.00% 0.00% 0.00% 0 Chunk Manager
2 58864 3290773 17 0.00% 0.00% 0.00% 0 Load Meter
3 1784 238001 7 0.07% 0.01% 0.00% 2 Virtual Exec
[code]....
View 1 Replies
ADVERTISEMENT
Jan 7, 2013
High cpu utilization on cisco 7206 vxr router.[code]
View 2 Replies
View Related
Jun 20, 2012
I am observing very high CPU utilization on my Cisco 7206VXR (NPE-G1) Router. We have done all the necessary troubleshooting but not able to identify root cause. [code]
View 10 Replies
View Related
Apr 19, 2011
I have a 7206VXR router doing policy routing with CEF enabled on all interfaces, no Cache Misses, Align Errors or failed buffers. CPU peaks up to 80% every two or three minutes. I suspect it is traffic related as I have a standby box and when it becomes the active on in the HSRP pair to high CPU load and LAN interface input errors follows it. see various show command output below. The router has a NPE-G1 and I'm using a gigabit port off of this on the LAn side and a E3 Frame Relay interface on the WAN side.
UK-DHC-Policy1#show buffersBuffer elements: 1118 in free list (1000 max allowed) 3539658545 hits, 0 misses, 1119 created
Public buffer pools:Small buffers, 104 bytes (total 50, permanent 50, peak 229 @
[Code].....
View 2 Replies
View Related
Mar 28, 2013
We have a Cisco 3845 router configured as a voice gateway with multi SIP trunks. But when it reachs 200 calls traffic, the CPU increase to 60-70% and caused by CCSIP_SPI_CONTROL process.
CPU utilization for five seconds: 46%/30%; one minute: 54%; five minutes: 58%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
377 400729448 171017979 2343 6.31% 10.71% 12.44% 0 CCSIP_SPI_CONTRO
[Code].....
View 2 Replies
View Related
Jan 31, 2012
We are facing high CPU Utilization on Cisco 3750X-48P-L without any traffic on it. find the attached log files for 2 separate 3750's stack, we have upgraded the IOS of SW2 from "c3750e-universalk9-mz.122-55.SE3.bin" to "c3750e-universalk9-mz.122-55.SE4.bin" but still we found the same issue with CPU utilization.
View 4 Replies
View Related
Apr 24, 2013
I've been looking at reported problems with our Vdeio Conferencing kit attched to a stack of 3750's (which I think is down to QoS) but this got me looking at the logs. We get a lot of high CPU utilization warnings mainly for SNMP (315), Hulc running con (95), Virtual exec (289). I understand the last two are normal, and the SNMP one is probably Cisco Works polling as it happens every 4 hours.
However I've got an odd one: Apr 25 07:34:58: %SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU Utilization(Total/Intr): 93%/0%, Top 3 processes(Pid/Util): 296/85%, 144/0%, 154/0%
What is Pid 296? It's not listed on the switch:
293 39056 18456 2116 0.00% 0.00% 0.00% 0 SpanTree Helper
294 8 73 109 0.00% 0.00% 0.00% 0 EEM Server
295 0 2 0 0.00% 0.00% 0.00% 0 EEM Policy Direc
[Code].....
View 7 Replies
View Related
May 20, 2012
From couple of weeks we have observed the cpu utilization of cisco 6509 with SUP 720 is high. During daytime from 9:00 to 21:00 it keeps increasing & reaches 98% & after 21:00 becomes normal.
View 5 Replies
View Related
Jan 13, 2013
I have a 2 cisco core (cisco WS-C6509-E (R7000) processor) and been working for quite sometime.they are conneted with HSRP with active standby config with a 10 g module for redundancy just today I see that the cpu utilization went to about 50% and its the same on both cores.
[Code] .......
View 5 Replies
View Related
May 3, 2012
I have some events where the CPU utilization in a cluster switches of WS-3750 is going to 100%, the process with the major utilization of CPU is the "hulc running con".
View 3 Replies
View Related
Feb 8, 2011
We have seen high CPU utilization on some Cisco switches of type 2960S. Also we got info, that applications are running with poor performance or with interruption.Following IOS is loaded: C2960s-universalk9-mz.122.55.SE
View 9 Replies
View Related
Sep 20, 2012
I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
View 1 Replies
View Related
Oct 19, 2012
In Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies
View Related
Dec 13, 2011
We have cisco 4510R+E switch with IOS-XE Software Version 03.01.01.SG RELEASE SOFTWARE (fc1).Our this switch is having two core & one core is always going to about 90% to 98% cpu utilization while other core is showing normal (about 5% to 10%),we check with-This switch is gateway of our LAN.
View 6 Replies
View Related
Dec 9, 2011
I am experiencing high cpu utilization in my 29501 switch. see the copied sh process cpu output.
CPU utilization for five seconds: 99%/95%; one minute: 89%; five minutes: 37%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 0 2 0 0.00% 0.00% 0.00% 0 Chunk Manager
[Code].....
View 4 Replies
View Related
May 22, 2012
I am running a 1712 12.4(25d) with NAT, VPN and FW/IDS. I have a broadband ethernet connection at 20mb. As I run some traffic through it, the processor jumps up to near 100% and throughput comes to a screeching halt. IP CEF is turned on and makes no difference when it is turned off or on.
View 3 Replies
View Related
Feb 16, 2012
I am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
View 4 Replies
View Related
Nov 2, 2010
I am looking at the utilization on a Catalyst 3560-E. I am running a test with eight 1 GIGE links RXing at 95 % utilization. All of the traffic is going to a TenGigE port. The device on the TenGigE port is echoing back all of the traffic received, so the 1 GIG links are TXing at 95% as well.When I do a "show controllers utilization", the port utilization numbers are correct, but the fabric utilization is higher than I would expect. The fabric should be 128 gigbits / second in this switch, and there is 7.6 gigabits TX/RX to the ten gig port. The fabric utilization is at 49%. I would expect 7.6 / 128 = 5.9% or possible double that. [code]
View 8 Replies
View Related
Jan 29, 2011
Cisco 6509 modular IOS getting high cpu in interrupt but the switch process switching is still less. Any sugeestion what could be the problem?
Process sbin/ios-base, type IOS, PID = 16407CPU utilization for five seconds: 12%/81%;
Sometimes cpu goes upto 100%
Version - s72033-ipservicesk9_wan-vz.122-33.SXH5
View 4 Replies
View Related
Feb 23, 2013
we have 2811 router with multiple servers connected to it's lan from which there are monitoring servers in between , the router suffers always from high cpu utilization
configuration has alot of ACLs & NAT & IPSEC Tunnel with wan bandwidth 20 M? Is there any method to reduce the high CPU utilization shown below !!
CPU utilization for five seconds: 90%/80%; one minute: 93%; five minutes: 90%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
104 737029848 427864243 1722 5.45% 5.65% 5.65% 0 IP Input
253 63392216 11081854 5720 1.04% 1.15% 1.12% 0 IP NAT Ager
260 82602372 137425723 601 0.64% 0.64% 0.66% 0 PDU DISPATCHER
[code]....
View 4 Replies
View Related
Feb 6, 2013
We have a Switch Catalyst 4500, model WS-C4510R+E, with 2 Supervisors, models V-10GE, which is showing high CPU values all times.When this occures, the switch shows 95-100% for total cpu for a few hours at a time.show proccesses cpu shows process Cat4k Mgmt LoPri with an unusual cpu value of 56% The show platform heath command gave me a high reading for K2L2 Address Table R which is curently 9,45% but the last hour is around a 20% average CPU ?[URL] what the process K2L2 Address Table R means and what could be the cause of this peak?
View 3 Replies
View Related
Jan 2, 2013
getting CPU utilization around 62%
CPU utilization for five seconds: 54%/6%; one minute: 61%; five minutes: 61%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
35 82081 9642 8512 0.31% 0.21% 0.18% 0 Compute load avg
[Code]....
View 1 Replies
View Related
Sep 6, 2012
I have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.
View 14 Replies
View Related
Sep 5, 2012
I have been facing High CPU Utilization issue with few of my Cisco 4006 Switches together from last one month. Out of which 1 switch issue sorted out auto after 2 days however the problem is still exists with rest 3 switches.They are 6-7 year old and having one SUP engine and other are switch port modules.
View 5 Replies
View Related
Oct 9, 2012
We have just purchased Cisco 3750X 24 S switches (QTY 2), last week we put them in prodcution in simple Layer 2 mode. No Core, just act as Access switch in order to only check the performace and availibility of switches.
But strange thing I have noticed the highest cpu utilization, cpu sits on 13 to 14% and from historical logs it hit above 60%. I am confused what is happening. Remember to terminate copper connection we have inserted Copper SFP Modules on both switches.
Both switches connected on Layer 2 mode via trunk, in LAN environment we have here 7 3Com 2824 Management switches which are terminated on Copper SFP modules at Cisco 3750X 24 S. All 3Comm Switches uplink are terminated on Cisco 3750 Switch 1, another switch is idle. Whole setup is running on VLAN1 .
Also refer no port in TCP and UDP packets in show ip traffic. any abnormal condition you predict..basically, In near days we plan to make these switches as Core layer and run intervlan routing, HSRP/VRRP and OSPF. But in this cpu usage how we can go ahead until this resolved..
View 36 Replies
View Related
Sep 25, 2012
We've got Cisco 2821 for our 90mb/s Internet Access. Its CPU usage is around 80%. Show process cpu does not show any cpu proccess with high utilization. But we have got plenty of policing configured for our clients using policy maps. Can this policing affect cpu usage?
View 1 Replies
View Related
Dec 6, 2011
I've noticed that my 6509's running VSS seem to have high I/O memory utilization.
I/O memory: Sw/Mod Bytes: Total Used %Used
1/1 8126344 7886544 97%
1/2 11796240 11442472 97%
1/5 RP 12058384 10715832 89%
1/5 SP 8388608 8104304 97%
1/7 8126344 7886544 97%
[code]....
View 5 Replies
View Related
May 2, 2013
I noticed on the 2960 switches we have deployed that are running the latest IOS, 12.2(58)SE2, memory utilization is really high (almost 80 percent). I have not noticed any side effects but I wanted to verify this is acceptable. My question is does the high memory utilization matter? I see this may be related to bug CSCtw83946 but no resolution is mentioned.
I did some testing various IOS revisions and below is what I have found using a WS-C2960-48TC-L with default configuration and only my laptop connected to a switchport in vlan1. You will notice memory utilization will grows with each version but jumps drastically with 58. One difference with 58 I needed to use a different command to retrieve memory utilization. The output was gathered by pasting the output of the show command into the Cisco Output Interpreter on their website.
IOS
Show Command
Output
c2960-lanbasek9-mz.122-35.SE5.bin
show memory
[Code]....
View 8 Replies
View Related
Jan 23, 2010
I have a Head Quarter and a remote site running over a OC3 circuit. [code]
On the HQ, I have a Cisco VXR7204 running IOS 12.4.15T(10) Advanced IP Serviceand the remote site is a Cisco 2851 also running IOS 12.4.15T(10) Advanced Ip Service. The HQ has a Riverbed Steelhead 5050H capable of delivering 100MbpsWCCP throughput. The remote site has a Riverbed Steelhead 1050H which can deliver 10Mbps WCCP throughput. At the HQ, the LAN network is 192.168.251.0/24.The Steelhead residing on the 192.168.251.0 network.At the remote site, the LAN network is 192.168.103.0/24 and 192.168.211.0/24.The Riverbed resides on the 192.168.103.0/24 network.
When a host on network 192.168.211.0/24 download a file from network192.168.251.0/24 network via http, the CPU on the Cisco 2851 goes to 99% utilization and that it stays there for the duration of the http session. There is very little traffic goes across the WAN whichis the way it should be but the CPU on the 2851 stays at constant at99% CPU utilization.
Why would WCCP consume so much CPU on the Cisco 2851? By the way, I am only getting about 5Mbps download instead of 90Mbps download, I think because of the high CPU on the router?
View 2 Replies
View Related
Dec 20, 2011
I am experiencing high cpu utilization in my 4000 series core switch.
I checked the loggs. i saw some strange loggs.
Please see the below logs:
Code...
What is the "invalidsourceaddresspacket" ?
Is this is due to some virus attack or something?? Also one more thing this switch is the Active router in HSRP.
View 12 Replies
View Related
Nov 9, 2012
I am facing high memory utilization in Cisco 2960 switch having IOS version 12.2(55)SE3.
The error we are getting is:
A "LiveHealthAlarm" event has occurred, from SwCiscoIOS device, named Switch2960. eHealth Alarm Start Time - Fri 09 Nov,2012 - 03:02:48 eHealth. Switch2960-RH-MemoryPool-Processor-Processor-1.Memory utilization high-Threshold set at 70%SPECTRUM ALARM ID|22233284 I have attached the logs also.
View 3 Replies
View Related
Feb 25, 2013
i am seeing very high utilization on a random basis on the stack. and the logs indicate me that there is a pattern where there is a stack power cable shows inserted (which was never unplugged) followed by sudden spike in the utilization.
001018: *Mar 6 16:21:22.138: %PLATFORM_STACKPOWER-6-CABLE_EVENT: Switch 4 stack power cable 1 inserted
001019: *Mar 6 18:18:37.982: %SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU
[Code]......
View 16 Replies
View Related
Jan 21, 2012
I have a new cisco 3750 stack comprised of 8 members (6 x 3750G-48PS and 2 x 3750V2-48PS) running 'c3750-ipservicesk9-mz.122-58.SE2.bin'. I am seeing high memory utilisation, it seems to sit fairly stable and I do not see an increase but this has only been running a few days. No errors or performance issues. Should this be a cause for concern?
View 3 Replies
View Related
