I have a Cisco 876 router, I need to connect ethernet WAN link, While configuring IP address am getting below error.
yourname(config)#int f0yourname(config-if)#ip addres 172.30.1.0 1. 255.255.255.0
% IP addresses may not be configured on L2 links.
I've been experiencing problems with internet speeds at my church and my home. They both have security keys, but many people use it. I was wondering - Is there a free tool to monitor who/which device is taking up all of the bandwidth? Something that kind of points out, "Hey, this guy is really slowing you down". Possibly even (But not necessarily) kill their connection?
View 1 Replies View RelatedWe have two ASA5510's, running IOS ver. 8.2(4). We setup Load Balancing on two ASA's. Will there be any problems if we change the IP address of the outside interface on one of the ASA's?
View 0 Replies View Relatedconfigure my cisco 892 router want a static ip address assigned to the interface because and I have no more internet on the router because am working on my network academy for CCENT?
View 28 Replies View RelatedI am currently working with a vendor to get my ASA5520 setup to handle IPsec VPN connections for my clients and we are stumped with how to get the outside interface to respond to connections/requests.
I work for a state agency and our network connectivity is provided to us by another agency/department. The firewall I want to use for VPN connectivity has an outside address of 10.0.8.162 which is not routable outside the state's network. I have been assigned a set of public IP addresses for servers in my DMZ and I am wondering if it is possible to configure the ASA to utilize one of those public IP addresses for VPN communication. My DMZ network is setup as a local 192.168.10.0 network and the ASA is performing NAT translations to the corresponding public IP addresses.
Putting in a NAT rule to translate one of the public IP addresses to the 10.0.8.162 outside interface, but I wasn't sure if that would work.
Why layer 2 switches need its mac address, even it does not have any interface ? (does not have stp and etc)
View 8 Replies View RelatedI was given a linksys SRW224G4 switch .. It seems to work fine on some ports and others dont,I am tring to log into it to see what the current config is . I cant seem to find what ip address its pulling to be able to log into the web interface. I have tried the blue cable , and using hypertermail but with no luck .. I dont have com 1 or 2 as an option on my latop just com 3. how I can log into this switch and rest it back to factory specs so then I can go though and setup how i want.
View 4 Replies View RelatedRecently, I've been having significant problems with denial of service on our ASA-5510. Two IP addresses in particular attack my ASA regularly. What kind of rule do I need to create to deny these IP's access to my firewall?
View 4 Replies View Relatedconfigure a secondary ip address (over the same address range) in a vlan interface on the SGE2000?For example, I want Interface Vlan 10 on mw switch has 172.16.10.1/24 and 172.16.10.2/24. Is that possible? If I try I get an error message with a duplicate IP address error. On Catalyst switches it can be done, but on Small Business?
View 1 Replies View RelatedI want to configure a MAC address on my asa 5520 interface.I ask you if exist a private MAC address range?
View 5 Replies View RelatedI need to know it the adsl router SRP547w or SRP546 permits to set class B subnetting ( or class A) on the Lan interface. I read the model SRP527 has a limitation to set ip address on the lan interface but I did not find any information about 547 or 546.
View 0 Replies View RelatedI have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?
Mobile devices are saturating our medium sized enterprise network. Examples of these devices are iPhones, iPads, Kindles, Droids, etc When a device is authenticated on our APMobile wireless network and downloads updates, email, or music our Network bandwidth is consumed. Services/Applications are no longer available, such as VoIP. Basically, this is an internal DoS.I have done some research and an example of this problem is an ARP Storm but currently clients obtain IP addresses form our DHCP server, which acts as a proxy for the clients and if effective against deliberate attempts to craft packets that create ARP Storm. In addition we configured the WLC to disable ARPunicast processing via the CLI.The following link is from Cisco's site. It is the ARPstorm that we originally thought was the cause but after more researching we found it wasn't this exact issue - http:[url]....why iPhones frequently take down our network? Could this be a configuration issue with our firewall (Cisco ASA 5520 running version 8.4(2))?
View 1 Replies View RelatedWe've recently upgraded our switches from 10/100 over to FOUR Dell 2848 (GB Managed switches) and using one as a director (fiber uplink).We are all on GB networks now and we've been running into issues tracking down what's hogging up most of our bandwidth (local area network) throughout our company.We need to track down which machines are copying data to servers and vise versa.
View 1 Replies View RelatedIt is good at times but usually it gets slow and web pages come up with "The web page is taking too long to respond". When I run Diagnose, sometimes I get the computer is correctly configured, but something is wrong with the DNS server (I dont know what that is). I have a NetGear CGD24G Wireless Router that was supplied by Charter when I got internet from them again. I also run Windows 7.
View 12 Replies View RelatedI installed a tp link extender to boost wifi at home (2 storey) and since then I have noticed that upstairs where the router is installed the signal is weaker than downstairs where the extender is located.
View 2 Replies View RelatedMy old Actiontec M1000 modem recently died and my HP nc6120 with windows XP can not connect to the wireless network through the new Actiontec C1000A model.It connected wirelessly through the old M1000 moden. Window icons on the screen indicate no wireless network is detected. When I view the available networks and log in to the assigned network with its password, it looks like it is trying to connect but does not. It will connect through the ethernet link-up. I don't have any other wireless devices to connect to the network. I have updated the drivers for the wireless card through HP. I have taken the HP nc6120 to the Geek Squad and the wireless card connects with their network. I seem to have a compatibility problem with the old HP with its XP windows operating software and the new modem system. I have tried to reset the ip addresses, but this has had no effect. However, I do have purchased AVG protection software operating on the system, which I am not sure how to shut off. Is this a problem with a too advanced modem for an old style HP with an XP operating system? Is there a modem that I can downgrade to if it is? [code]
View 3 Replies View RelatedMy Multi-media tab is not taking my wireless password? I have a d'link DIR-601; I reset the password using the web interface, but no matter what I try it doesnt link to my tab.What am I doing wrong ?
View 1 Replies View RelatedPast couple of weeks trying to connect to some websites. It is only SOME, not all websites. It will either say that it is taking too long to connect or that the website is experiencing problems. I have no idea where to start as i am pretty clueless when it comes to configuring/repairing network related issues.
View 3 Replies View RelatedI'm trying to get started on setting up my first Transparent ASA.I understand an ASA in Transparent Mode can now have an ip address with Bridge Groups or some such mechanism. I'm looking for examples of how to set that up and other information below. Is the ip address associated with the device or is it interface specific? Will I be able to SSH with that ip address setup? Can I use ASDM if the Transparent ASA has an ip address? This 5512X has an IPS. Any one who has setup an IPS on this platform knows it has some very particular requirments in order to communicate with the outside world. I need examples of how to do that with a Transparent ASA.How is NAT setup differently (if at all) on a Transparent ASA?Are ACLs done any differently?
View 3 Replies View RelatedI have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
I have a Catalyst 3750 Metro running 12.2(25)EY4.Every time I add or remove an ipv4 address from a tunnel interface I have the following log:
Jan 4 10:42:19.088: %PLATFORM_HCEF-3-ADJ: Insane handle in add LT7
-Traceback= 25222C A81C70 A7B28C B08958 B28940 B2A2E0 B2A684 B9EFA4 B9F004 B9F684 B9F814 B9F99C B8E3BC BA1BD8 3DFA94 39BA3C
We have an ASA 5510 and we also have two separate address pools which have been provided by our ISP. The addresses are not contiguous. Is there a way to configure an interface on the ASA to handle both sets of public address pools? If the outside interface is set up on eth0/0 would I create two subinterfaces (eth0/0.1, eth0/0.2) and assign each subinterface an address pool? Then just NAT/PAT to my heart's content? At that point I would want both to route to our inside network. So it's basically two inbound sets of IP addresses comming into one interface and then comming into the network... Right now the outside interface is configured with our first set of IP addresses. We wanted additional addresses and when we called our ISP they told us we already had them - just a different pool. Hence the question. I'm guessing that I wouldn't put anything specific on the outside interface and I would put the specifics on the subinterfaces?
View 4 Replies View RelatedI have a Cisco 2811 with fa 0/0 as my bearer, and a switch module for internal clients.
I have an issue with my fa 0/0 flapping, I want to move that ip configuration to fa 0/1
as this is a branch office I am reliant on the bearer port to give me coms so changing the IP addresses is difficult.
Has any one tried this with a TCL script?
I have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
we have two Cisco ASA 5510 in failover configuration.We tried to change the public IP address on the Outside interface of the primary device but it didn't works. The new IP is not reachable from Internet nor pingable from device on the same LAN.The new IP address is in the same subnet of the old IP.
From the switch on which the ASA is connected and from another Cisco PIX we can see the ARP entry. In the analysis, on the old public IP address there was a VPN site-to-site and Webvpn defined.We tried also to shut/no shut the interface and reboot the device.
We've had issues with our Exchange 2010 server (running on ESXi 4.1) since its default gateway was changed to our new ASA 5510. They manifested as frequent Outlook client connection dropouts or as IP address conflicts whenever Exchange was rebooted. The temporary fix was to disable the Exchange server NIC, bounce the ASA and enable the server's NIC again. We saw poor performance from Exchange after a while again, but after some research and testing I realised that disabling proxyarp on the inside interface fixed the problem permanently.
However I've now realised that the client VPN no longer routes properly because proxyarp is disabled on the inside interface, so I still have a problem.
I always though that sh mac address table dynamic interface xx/xx/xx was a subset of "sh mac address table" 6590 Version 12.2(33)SXI I have two mac addresses on downstream switches that will only show up when using
sh mac address-table dynamic interface Te4/10
* 903 0050.77a9.6e3c dynamic Yes 0 Te4/10
* 903 0050.77a9.5766 dynamic Yes 0 Te4/10
when using "old faithful"
sh mac address-table | inc 6e3c
*nothing*
or
sh mac address-table dynamic | inc 6e3c
*nothing*
nothing shows up?this vlan has no layer three interfaces
So I have a current port-channel between two 6ks that I need to upgrade. There's too much traffic and the port buffers on the SUP7203B sort of suck. Microbursts are causing overruns like mad. Im going to move the 2x1gig port-channel to a 6724 and make it a 3x1gig port-channel. The switches carry production traffic across the link to the tune of about 400 meg during the lowest load time. Initially, I thought that I couldn't move the port channel without temporarily taking down the link but I think I have a workable solution now. Has anyone done this successfully before? Im curious what others have done. Also, to make matters worse, the existing port-channel is 'mode on' and I want to migrate to 'mode active' in the new channel
View 7 Replies View RelatedI've inherited a 7206VXR router and it takes very long to boot. It outputs READonly ROMMON initialized to the console and 14 minutes later it continues the boot process. After 17+ minutes the boot is complete with the correct full image. The processing engine I have is the NPE-G1 and I'm looking for an upgradeable ROMMON image or a reason why the boot is taking this long.
View 1 Replies View RelatedUpgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail. How do I take the incoming traps (Crit and Warning) and send an e-mail alarm. I'll plan to control what to trap on at the Cisco Equipment.
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS. Now I want take that trap and forward via an email.
I have been reading the admin documentation on "Notification and Action Setting". I see how to take the Cisco LMS created trap and email alarm. (In this case I need a specific trap that LMS did not have.) I see how to take Cisco Traps and resend them to other NMS.
I work on a college campus that has thousands of students a day accessing our wireless network. We have broadcast SSID that the students use to connect to the internet. The students usually have more than one WiFi enable device on them and their laptops and phones both take an IP address, but they are only using the laptop to authenticate while the phone is associted, but not authenticated. In the meantime, I have several thousand IPs being used by their phones/iPods etc. Is there a way to revoke the DHCP lease if the client does not authenticate within a specified time frame (i.e. 10 minutes)?
View 3 Replies View RelatedI'm in the throes of configuring my 5520 to supply different group policies based on LDAP group membership. I'm finding that no matter what I do only the default group is applied. I'm sure it'll be a simple fix - but I just can't see it. [code]
View 4 Replies View Related