Cisco Switches :: Linksys SRW224G4 - What IP Address Able To Log Into Web Interface
Feb 2, 2012
I was given a linksys SRW224G4 switch .. It seems to work fine on some ports and others dont,I am tring to log into it to see what the current config is . I cant seem to find what ip address its pulling to be able to log into the web interface. I have tried the blue cable , and using hypertermail but with no luck .. I dont have com 1 or 2 as an option on my latop just com 3. how I can log into this switch and rest it back to factory specs so then I can go though and setup how i want.
View 4 Replies
ADVERTISEMENT
Jul 12, 2012
I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:
Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
How to regaining control of this supposedly smart switch?
View 3 Replies
View Related
May 24, 2011
I was wondering if there was a difference between the Linksys SRW224G4 & Cisco SF300-24 switches. Going through the support docs I see the SF300 has limited L3 functionality in terms of being able to establish static routes between VLANS. Any further information would be of use.
View 2 Replies
View Related
Jul 28, 2009
I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
[Code].....
View 12 Replies
View Related
Jan 19, 2013
I'm trying to upgrade a switch SRW224G4 but without success. Model Name SRW224G4 Hardware Version 00.03.00Boot Version 1.0.0.06
I send the file via the XModem( SRW2xxG4_FW_1.2.3.0 ).
View 2 Replies
View Related
May 8, 2013
After some wireshark, I see that when I have a vLan on the switch, only win7 gets IP, my macbook doesn't, sniffing to the bootp, I see that the DHCP sends NAK and after I only have DISCOVER & OFFER...
When I get the same switch and the same router and take out the vLan on the switch, everybody get an IP. What's the deal with this switch and vLans and Mac OS x ? Do I have to setup something else ?
View 1 Replies
View Related
Aug 15, 2012
We have small network with 15 Computers all connected to SRW224G4 . After a power brake our switch dosent "boot" anymore. I see all leds working flashing etc but no network acces, no Serial acces. When i try connecting to serial port and "reset" device the screen is blank.
View 1 Replies
View Related
Dec 27, 2011
Why layer 2 switches need its mac address, even it does not have any interface ? (does not have stp and etc)
View 8 Replies
View Related
Aug 18, 2011
configure a secondary ip address (over the same address range) in a vlan interface on the SGE2000?For example, I want Interface Vlan 10 on mw switch has 172.16.10.1/24 and 172.16.10.2/24. Is that possible? If I try I get an error message with a duplicate IP address error. On Catalyst switches it can be done, but on Small Business?
View 1 Replies
View Related
Dec 13, 2011
I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
View 3 Replies
View Related
Jan 14, 2013
I would like to upgrade the firmware on my SRW224G4 switch but I don't know which file I should be using. When I go to download firmware I see links for the following
"Cisco SRW224G4 24-port 10/100 + 4-port Gigabit Switch - WebView"
Which has firmware 1.2.3.0
"Cisco SRW224G4 24-port 10/100 + 4-port Gigabit Switch - WebView V1.0"
Which has firmware 1.2.2a
I'm not sure which firmware I should use, and the last thing I want is to brick this switc.
Below are the current firmware details
Boot Version: 1.0.2 (Date: 17-Aug-2006, Time: 14:55:46)
Software Version: 1.2.1b (Date: 31-Aug-2006, Time: 13:47:21)
Hardware Version: 00.03.00
View 1 Replies
View Related
Apr 25, 2012
i need to know that how can i make vlans in Linksys SRW224G4 Layer 2 manageable switch , because i have 100 users network having lots of users using more then 1 ip to connect 4 different servers having different ip class pools, what i need is, i want to use only single ip pool with Class B Address like 172.16.6.0 for all network users which all connect to far end servers through layer 2 Linksys SRW224G4 manageable switch controlling to allow different IP pools ? like 172.16.1.0 / 172.16.55.0 / 172.16.99.0 and 192.168.1.0
View 1 Replies
View Related
Jun 16, 2011
I have a linksys router model#wrt54gt v1 and I can not pull up the router's ip address to change the security settings. I have checked and I have the correct IP address of 192.168.1.1. I can ping the router and everything hooked up to the router is now working correctly. I was having problem with the router losing the internet ip address and having to turn everything off and then back on to connect to the internet. I reset the router and it seems to have corrected that problem but I now can not pull up the router's ip address. I have tried in Internet Explorer and Firefox. I have tried typing thebefore the ip address but it will not pull up. I have read countless posts trying to trouble shoot and figure out what's wrong with it and nothing will work.
View 5 Replies
View Related
Sep 20, 2012
we just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies
View Related
Mar 22, 2012
One of our costomers has a SRW224G4 Switch - which has not any documentation :-(
I do not get onto the switch in any way. I do not have an IP-Address, the default settings for he serial port do not work ... So I cannot reach the device and reset the password like described in: [URL]
Is there any other way to reset the device? I cannot find any reset button.
View 1 Replies
View Related
Jan 16, 2012
I have a Cisco 876 router, I need to connect ethernet WAN link, While configuring IP address am getting below error.
yourname(config)#int f0yourname(config-if)#ip addres 172.30.1.0 1. 255.255.255.0
% IP addresses may not be configured on L2 links.
View 3 Replies
View Related
Dec 5, 2011
We have two ASA5510's, running IOS ver. 8.2(4). We setup Load Balancing on two ASA's. Will there be any problems if we change the IP address of the outside interface on one of the ASA's?
View 0 Replies
View Related
Feb 7, 2012
configure my cisco 892 router want a static ip address assigned to the interface because and I have no more internet on the router because am working on my network academy for CCENT?
View 28 Replies
View Related
Aug 29, 2012
I am currently working with a vendor to get my ASA5520 setup to handle IPsec VPN connections for my clients and we are stumped with how to get the outside interface to respond to connections/requests.
I work for a state agency and our network connectivity is provided to us by another agency/department. The firewall I want to use for VPN connectivity has an outside address of 10.0.8.162 which is not routable outside the state's network. I have been assigned a set of public IP addresses for servers in my DMZ and I am wondering if it is possible to configure the ASA to utilize one of those public IP addresses for VPN communication. My DMZ network is setup as a local 192.168.10.0 network and the ASA is performing NAT translations to the corresponding public IP addresses.
Putting in a NAT rule to translate one of the public IP addresses to the 10.0.8.162 outside interface, but I wasn't sure if that would work.
View 1 Replies
View Related
Jun 23, 2011
Recently, I've been having significant problems with denial of service on our ASA-5510. Two IP addresses in particular attack my ASA regularly. What kind of rule do I need to create to deny these IP's access to my firewall?
View 4 Replies
View Related
Aug 31, 2006
I want to configure a MAC address on my asa 5520 interface.I ask you if exist a private MAC address range?
View 5 Replies
View Related
Jan 13, 2013
I need to know it the adsl router SRP547w or SRP546 permits to set class B subnetting ( or class A) on the Lan interface. I read the model SRP527 has a limitation to set ip address on the lan interface but I did not find any information about 547 or 546.
View 0 Replies
View Related
Oct 19, 2011
I have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?
View 9 Replies
View Related
Jan 21, 2013
I'm trying to get started on setting up my first Transparent ASA.I understand an ASA in Transparent Mode can now have an ip address with Bridge Groups or some such mechanism. I'm looking for examples of how to set that up and other information below. Is the ip address associated with the device or is it interface specific? Will I be able to SSH with that ip address setup? Can I use ASDM if the Transparent ASA has an ip address? This 5512X has an IPS. Any one who has setup an IPS on this platform knows it has some very particular requirments in order to communicate with the outside world. I need examples of how to do that with a Transparent ASA.How is NAT setup differently (if at all) on a Transparent ASA?Are ACLs done any differently?
View 3 Replies
View Related
Apr 19, 2012
I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
View 3 Replies
View Related
Jan 3, 2007
I have a Catalyst 3750 Metro running 12.2(25)EY4.Every time I add or remove an ipv4 address from a tunnel interface I have the following log:
Jan 4 10:42:19.088: %PLATFORM_HCEF-3-ADJ: Insane handle in add LT7
-Traceback= 25222C A81C70 A7B28C B08958 B28940 B2A2E0 B2A684 B9EFA4 B9F004 B9F684 B9F814 B9F99C B8E3BC BA1BD8 3DFA94 39BA3C
View 3 Replies
View Related
Dec 25, 2012
We have an ASA 5510 and we also have two separate address pools which have been provided by our ISP. The addresses are not contiguous. Is there a way to configure an interface on the ASA to handle both sets of public address pools? If the outside interface is set up on eth0/0 would I create two subinterfaces (eth0/0.1, eth0/0.2) and assign each subinterface an address pool? Then just NAT/PAT to my heart's content? At that point I would want both to route to our inside network. So it's basically two inbound sets of IP addresses comming into one interface and then comming into the network... Right now the outside interface is configured with our first set of IP addresses. We wanted additional addresses and when we called our ISP they told us we already had them - just a different pool. Hence the question. I'm guessing that I wouldn't put anything specific on the outside interface and I would put the specifics on the subinterfaces?
View 4 Replies
View Related
Aug 29, 2012
I have a Cisco 2811 with fa 0/0 as my bearer, and a switch module for internal clients.
I have an issue with my fa 0/0 flapping, I want to move that ip configuration to fa 0/1
as this is a branch office I am reliant on the bearer port to give me coms so changing the IP addresses is difficult.
Has any one tried this with a TCL script?
View 4 Replies
View Related
Aug 22, 2011
I have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
View 6 Replies
View Related
Mar 10, 2011
we have two Cisco ASA 5510 in failover configuration.We tried to change the public IP address on the Outside interface of the primary device but it didn't works. The new IP is not reachable from Internet nor pingable from device on the same LAN.The new IP address is in the same subnet of the old IP.
From the switch on which the ASA is connected and from another Cisco PIX we can see the ARP entry. In the analysis, on the old public IP address there was a VPN site-to-site and Webvpn defined.We tried also to shut/no shut the interface and reboot the device.
View 1 Replies
View Related
Apr 5, 2012
We've had issues with our Exchange 2010 server (running on ESXi 4.1) since its default gateway was changed to our new ASA 5510. They manifested as frequent Outlook client connection dropouts or as IP address conflicts whenever Exchange was rebooted. The temporary fix was to disable the Exchange server NIC, bounce the ASA and enable the server's NIC again. We saw poor performance from Exchange after a while again, but after some research and testing I realised that disabling proxyarp on the inside interface fixed the problem permanently.
However I've now realised that the client VPN no longer routes properly because proxyarp is disabled on the inside interface, so I still have a problem.
View 10 Replies
View Related
Apr 23, 2012
I always though that sh mac address table dynamic interface xx/xx/xx was a subset of "sh mac address table" 6590 Version 12.2(33)SXI I have two mac addresses on downstream switches that will only show up when using
sh mac address-table dynamic interface Te4/10
* 903 0050.77a9.6e3c dynamic Yes 0 Te4/10
* 903 0050.77a9.5766 dynamic Yes 0 Te4/10
when using "old faithful"
sh mac address-table | inc 6e3c
*nothing*
or
sh mac address-table dynamic | inc 6e3c
*nothing*
nothing shows up?this vlan has no layer three interfaces
View 1 Replies
View Related
Mar 22, 2012
I have a new router. this seems to be a very simple problem relating to the most basic configuration options.
Hardware Version: A1 Firmware Version : 1.01NA
go to SETUP -> "NETWORK SETTINGS"
change "Router IP Address" to 192.168.73.1
change "DHCP IP Address Range" to: 192.168.73.10 : 192.168.73.200
Save Changes Wait for reboot. change my client system's local IP address... so that I can reconnect. direct web browser to http://192.168.73.1/
seen: login page has a select-box for a userid, but no text inside. there is no prompt to ask me to login. I press enter (or whatever... I login). every form interface on all web pages looked at have no labels on text boxes.
I did a view source... and used web-dev tools to look at the page. it looks like the apparent js function, show_words(), is not defined.
change ip address and dhcp address range back to default save changes. wait for reboot. reverse changes to local system things are back to normal. login page has useful text. after logging in, there is something to read.
looking at source again. I see, now, that the js function "show_words" is defined in a file called public.js.
View 5 Replies
View Related
