Protocols / Routing :: Make Vlans In Linksys SRW224G4 Layer 2 Manageable Switch?
Apr 25, 2012
i need to know that how can i make vlans in Linksys SRW224G4 Layer 2 manageable switch , because i have 100 users network having lots of users using more then 1 ip to connect 4 different servers having different ip class pools, what i need is, i want to use only single ip pool with Class B Address like 172.16.6.0 for all network users which all connect to far end servers through layer 2 Linksys SRW224G4 manageable switch controlling to allow different IP pools ? like 172.16.1.0 / 172.16.55.0 / 172.16.99.0 and 192.168.1.0
View 1 Replies
ADVERTISEMENT
Feb 4, 2011
I'm setting up a Cisco 3750 layer 3 switch with several vlans. I thought enabling routing would route between the vlans, but no such luck.What I want is to share the internet access of vlan 100 with the other vlans/ip-nets.How can I do that?
View 2 Replies
View Related
Dec 26, 2012
I am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans. It is connected to my router address 192.168.1.1. I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet.
Here is the config that I have. I deleted the other ports because I am not using them. The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1.
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code]....
View 12 Replies
View Related
May 17, 2011
I just inherited a network and feel like.I am missing something. We use ATT&T Opt-E-Man which limits the MAC address to 50 for the connection or you have to pay.Hence the routing VLAN is the only access across the two sites.I have a VoIP vendor who insists on using the same VLAN for all sites. Upon exam the VLAN is at the remote site but it does not work.
View 2 Replies
View Related
Apr 26, 2012
just a simple question. Is it possible to use a nexus 5548 UP switch as a layer 3 router between different vlans on the switch without the layer 3 card ? Or is there no 5548 as a router with the layer 3 card ?
View 2 Replies
View Related
Oct 19, 2012
How can I make sure R11 is able to get the OSPF routes of all the areas. Make sure area-278 does not receive any ospf routes from other areas as well as from ASBR routes from other areas. At the same tim, area-278 should be able send successfully RIP routes that we receive from R2 to backbone area.
View 1 Replies
View Related
Jan 7, 2013
The question is apparently simple. A network is given, consisting of
- 1 network core switch: HP 5500-EI (Layer3)
- 4 access switches: HP 5120-EI (Layer2)
They are connected in the shape of a star (the core switch in the center)The task is to measure the occupation rate of this network on a per-VLAN basis.
For example : To be able to generate statistics like: During the last week - Monday to Sunday - the netowork occupation with VLAN 10 traffic was 30% and VLAN 60 traffic was 70%.
View 1 Replies
View Related
Apr 16, 2013
I have a computer named server and it ip is 192.168.0.5 and a live ip xxxxxxxx which is a private ip. on this system my oracle middle wear is running.I just want that people may access my application which is running on 'server' through public ip. Is it possible. If it is. then how.=]
View 1 Replies
View Related
Jan 14, 2013
I would like to upgrade the firmware on my SRW224G4 switch but I don't know which file I should be using. When I go to download firmware I see links for the following
"Cisco SRW224G4 24-port 10/100 + 4-port Gigabit Switch - WebView"
Which has firmware 1.2.3.0
"Cisco SRW224G4 24-port 10/100 + 4-port Gigabit Switch - WebView V1.0"
Which has firmware 1.2.2a
I'm not sure which firmware I should use, and the last thing I want is to brick this switc.
Below are the current firmware details
Boot Version: 1.0.2 (Date: 17-Aug-2006, Time: 14:55:46)
Software Version: 1.2.1b (Date: 31-Aug-2006, Time: 13:47:21)
Hardware Version: 00.03.00
View 1 Replies
View Related
May 29, 2011
I have a Compaq mini CQ10-100 Netbook, and I am trying to Make a Wireless internet connection through a D-link router. My ISP is Cox Cable. The Netbook is connected to my wireless network, but will not connect to the internet. It keeps asking me to transfer information, via thumb drive, from a wireless access point, but my router is my wireless connector and it doesn't have a USB port to plug in a thumb drive. How do I get this netbook hooked up to the internet?
View 1 Replies
View Related
Aug 15, 2012
We have small network with 15 Computers all connected to SRW224G4 . After a power brake our switch dosent "boot" anymore. I see all leds working flashing etc but no network acces, no Serial acces. When i try connecting to serial port and "reset" device the screen is blank.
View 1 Replies
View Related
Apr 26, 2012
I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
View 11 Replies
View Related
Apr 17, 2011
Data link-ARP,RARP, presentation-SSL,TSL,ASCII,JPG, Session layer-ASP(apple talk session protocol),SCP are these correct?can your provide 2 new protocols for each with the long name?
View 17 Replies
View Related
May 5, 2012
I'm fairly new to networking but I've learned quite a bit on my own without being educated. I'm trying to just figure things out on my gear. So for my LAN party i'm going to need an internet connection. I'm not going to rely on my venues subnet though so i want to create a new /24 subnet(250 hosts is good for a start). I want my subnet to be able to speak to the outside network too.
View 8 Replies
View Related
Aug 24, 2011
I got one SF 300-48 layer 3 switch I tried to configure to use it in the office network.Unfortunately I'm unable to configure the VLAN settings.I need port one for input(VLAN2),port 7-15 for another vlan(vlan3) also need to connect with the vlan 4.port 15 is another vlan(vlan4) this is for wireless.Other ports are static.It doesn't get any connections with other vlans.I wish to know how to configure vlans in GUI mode.I tried , But I can't get the Vlan setting correctly.Also,I need to know how to communicate both vlans in GUI mode.
View 8 Replies
View Related
Apr 29, 2013
I created a lab and I have a few issues. One with a layer 3 switch and another with a ASA 5550.
1. Layer 3 switch: I have created multiple Vlans and I am able to route between them. I can ping the switch IP but not the default gateway to the ASA. I did a tracert of the default gateway of the ASA and once I am past the Vlan gateway it fails.
2. On the ASA 5550 I created the Vlans on sub-interfaces but still cannot get to the internet. ASA config is below the switch config.
View 7 Replies
View Related
Apr 13, 2013
I am tryingto add a new VLAN on my C3560E Layer 3 switch for administration purpose.My goal is to make this VLAN for administration only and to let the administrators from 172.17.1.1 connect to any host of the internal network 172.16.0.0 plus exit to the internet via the default gateway 172.16.1.245.
Here an extract of what done so far:
ip routing
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
!
interface GigabitEthernet0/1
[Code]...
What happened is that:
1. The host connected to Vlan30 can correctly ping the interface it is connected to.
2, The internal network can access the internet
3. The host connected to VLAN30 cannot access the internet and cannot connect to any internal server.
Do I have to add a static route? This is a production envuironment and it is my first experiment with a layer3 switching in production, so I cannot mistake
View 19 Replies
View Related
Feb 9, 2012
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
View 5 Replies
View Related
Jan 13, 2013
I've created a scenario using a 3750 cisco as core switch ad other 6 switch model 2900 in access level.my problem is this, the router is not a cisco router, and this router is not able to make NAT on more than one subnet.Into the core switch I've created 4 VLAN and I must to give internet access to 3 of them, 192.168.0.0/24 (vlan1), 172.16.0.0/24 (vlan2), 172.17.0.0/24 (vlan3).I've connected the switch to router via gigabit ethernet 0/1 and I've assigned to this interface ip address 192.168.10.2, the router ip address is 192.168.10.1, Switch ip default-gateway is router ip address 192.168.10.1, ip default route is 0.0.0.0 0.0.0.0 192.168.10.1 I've enabled ip routing feature and I've set no switchport feature to interface gigabit ethernet 0/1.From core switch I can ping router ip address but I can't make it from all other user, and the users not able to have internet access.
Below the switch configuration (only necessary strings)
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code].....
View 6 Replies
View Related
Sep 5, 2012
My understanding is that even layer 2 switches like the Cisco 3500XL can have 1 IP address for management. However, I cannot seem to figure out how to configure it to get it working in a router on a stick setup. I can manage the router through SSH, but I cannot SSH to the switch.
View 3 Replies
View Related
May 25, 2012
I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.
View 3 Replies
View Related
Oct 16, 2012
is it possible to run a Catalyst 4500 as pure Layer 2 Switch, i.e. disabling "ip routing", but still managing the switch via Fa1, i.e. the defautl mgmtVrf vrf ?I tried the following:
!
no ip routing
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address 192.168.1.1 255.255.255.0
!
ip route vrf mgmtVrf 0.0.0.0 0.0.0.0 192.168.1.254
ip default-gateway 192.168.1.254
I was not able to reach the Switch even from the same subnet. Only after enabling ip routing I could manage the Switch. I haven't found any command to set ip default-gateway for a vrf. Any workaround to keep routing disabled, but still manageable via VRF?
View 3 Replies
View Related
Feb 9, 2013
I have a question about QoS and how, or if, it functions between a layer 2 switch and a router. My question is, can a frame's COS sent from a layer 2 switch to a router be recognized and converted (mapped) to a DSCP setting without the use of a vlan (not the native vlan1), and can the reverse be done from a router to a layer 2 switch? Can QoS be preserved as it passes through the different devices? I know, pretty basic, but I have to start somewhere.
View 12 Replies
View Related
Apr 12, 2013
Configuring OSPF on a catalyst 3560G Switch to connect to our building next door by way of fiber. The other two switches in the other building are running OSPF, I am trying to connect to the other building and access a server which is on a switch running OSPF. I am trying to configure the switch here to run OSPF and be able to see the neighbor, but currently can't although I've identified the networks. Maybe I'm missing something, I've followed the instructions but something is not right.
View 15 Replies
View Related
Nov 29, 2012
RACK 1 is the old rack and NEW RACK is the rack which is going to be procurred for some new Servers. All the Servers in the RACK 1 has a default gateway as PIX Inside IP. As of now the 3560 Switches acts as Layer 2 and does not have L3 IP routing enabled. How can I enable conenctivity between 192.168.36.0 range and 192.168.57.0 range wihtout making any change to current PIX inside IP address 192.168.57.1?Is it possible that I can enable IP routing on the 3560 Switches , create interface VLAN 36 and since already Switch 2 has it 's default gateway as 192.168.57.1 , Would the traffic from 192.168.36.0 be routed to 192.168.57.1 ? Or do I need to create static route for that ?Since L3 Routing is not enabled and since the 3560 Switches are just acting as L2 , the VLAN 2 - 192.168.57.0 range does not have any interface VLAN configured. When it is changed I would need to create interface VLAN 2 on 3560 Switches?
View 18 Replies
View Related
Dec 23, 2012
I just received a Catalyst 2960-C (WS-C2960C-8TC-L R) switch and I am unable to sign into its web GUI in order to configure it. I've tried both the Cisco Network Assistant and Internet Explorer and I am unable to log in either way. The documentation provided by Cisco states that the default password is simply cisco and that a username is unnecessary. Needless to say, it doesn't work. I've also Googled for other default passwords (such as cisco-cisco as the username-password), none of which worked either. I've also tried resetting the switch back to its factory default a few times.
View 8 Replies
View Related
May 23, 2012
I'm building the below network configuration:
WAN -------- ASA5505 ------<802.1q trunk>----- L3 switch -----<802.1q trunk>----- L2 switch w/ VLAN support
The following VLANs exist on the ASA and both switches: VLAN 10 (10.10.10.0/24), VLAN 11 (10.10.11.0/24), and VLAN 99 (10.10.99.0/24).
The ASA5505 performs the following functions: routing to/from the WAN, firewall, NAT, and DHCP for each VLAN. It has an interface on each VLAN (10.10.x.2) for a DHCP server.
The L3 switch provides inter-VLAN routing and layer 2 switching. The L2 switch provides layer 2 switching, with VLAN support.
What should the default gateway on the L3 switch be? Should I set the IP of the physical interface connected the L3 switch to the ASA5505.
View 8 Replies
View Related
Jan 9, 2012
I would like to know if ip helper-address feature is working on a layer 2 switch (2950,2960) or you should use a Layer 3 switch to do that?
View 7 Replies
View Related
Jul 30, 2012
Configured Layer 3 portchannel from 6500VSS enabled switch to two different 6500 standalone switch. Configured first ip on VSS switch, second ip on standalone switch1 and third IP on standalone switch2. My question is
1. Will the portchannel be up?
2. If port channel is up, will I able to ping the connected IP's.
View 1 Replies
View Related
May 16, 2013
We are working with a contractor to upgrade our network, and I heard from them that the 5596/5548 might not need the Layer 3 module for our inter-VLAN routhing. They have yet to give me an answer.
We do have a few static routes on our current layer-3, core switch too.
View 3 Replies
View Related
Dec 3, 2011
I need a L2 switch with dual AC power supply and RJ45 uplink The optin I got was WS-C3560X-48T-L + C3KX-PWR-350WAC , but the problem is with uplink . There is no RJ45 1G uplink , there is only option for SFP uplink The another option was WS-C2960G-48TC-L , but there is no dual AC power supply option a good model ( Dual AC power supply , RJ 45 uplink ports (Gig) , with 48 port 100/1000 UTP)
View 3 Replies
View Related
Mar 18, 2009
Can a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies
View Related
Feb 14, 2013
can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies
View Related
