I'm trying to upgrade a switch SRW224G4 but without success. Model Name SRW224G4 Hardware Version 00.03.00Boot Version 1.0.0.06
I send the file via the XModem( SRW2xxG4_FW_1.2.3.0 ).
I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
[Code].....
I would like to upgrade the firmware on my SRW224G4 switch but I don't know which file I should be using. When I go to download firmware I see links for the following
"Cisco SRW224G4 24-port 10/100 + 4-port Gigabit Switch - WebView"
Which has firmware 1.2.3.0
"Cisco SRW224G4 24-port 10/100 + 4-port Gigabit Switch - WebView V1.0"
Which has firmware 1.2.2a
I'm not sure which firmware I should use, and the last thing I want is to brick this switc.
Below are the current firmware details
Boot Version: 1.0.2 (Date: 17-Aug-2006, Time: 14:55:46)
Software Version: 1.2.1b (Date: 31-Aug-2006, Time: 13:47:21)
Hardware Version: 00.03.00
Recently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies View RelatedWe have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
View 6 Replies View RelatedI have just attempted to load the latest firmware on an SLM2008, everything appeared to work as expected BUT, the switch is no longer pingable on its static IP doesn't appear to have attempted get an address via DHCP. I have attempted power cycling the switch but it has made no difference. The switch is still switching but I have no management any more. What to do next ?
View 1 Replies View RelatedI was given a linksys SRW224G4 switch .. It seems to work fine on some ports and others dont,I am tring to log into it to see what the current config is . I cant seem to find what ip address its pulling to be able to log into the web interface. I have tried the blue cable , and using hypertermail but with no luck .. I dont have com 1 or 2 as an option on my latop just com 3. how I can log into this switch and rest it back to factory specs so then I can go though and setup how i want.
View 4 Replies View RelatedI was wondering if there was a difference between the Linksys SRW224G4 & Cisco SF300-24 switches. Going through the support docs I see the SF300 has limited L3 functionality in terms of being able to establish static routes between VLANS. Any further information would be of use.
View 2 Replies View RelatedAfter some wireshark, I see that when I have a vLan on the switch, only win7 gets IP, my macbook doesn't, sniffing to the bootp, I see that the DHCP sends NAK and after I only have DISCOVER & OFFER...
When I get the same switch and the same router and take out the vLan on the switch, everybody get an IP. What's the deal with this switch and vLans and Mac OS x ? Do I have to setup something else ?
I've been having a problem with a brand new SG300-10 switch that I posted about yesterday. I checked the firmware and it was at 1.0.0.27 and the lastest is 1.1.0.73. So I backed up the current firmware and loaded the 1.1.0.73 version and it seem to be CLI based only, with no web GUI.
If so is there an easy way to reload the 1.0.0.27 using the CLI? There is nothing in the CLI docs that I can see unless it's buried.
The release notes for 1.1.0.73 don't say it's CLI only either, maybe something just went wrong but the CLI seems to be functional.
After performing a firmware upgrade on an SG300-20 switch from ver 1.1.0.73 to 1.2.5.70 the switch now boots up with the following error and resets:
30-Aug-2011 10:47:33 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter %s is too long.
The attached file contains a full output of the console boot process. I have tried loading different versions from the console, but all produce the same error.
Using the SGE 2010 for Microsoft NAP with 802.1x auth for switch access, which led to a few issues
What i have: An SGE 2010 48 port switch, firmware 3.0.0.17 Firmware upgrade: In order to ensure im not having problems due to old firmware, i tried to upgrade using ros_ls1_bp_ge_bx-3020.ros in order to move to 3.0.2, when uploading the file via TFTP, the upload completes and thats it, nothing happens.Restarting the device: As part of the upgrade process, i thought i might of had to reboot, so i rebooted, and found that all my settings were wiped clean, as if a factory reset had been performed.... and add further to pain, the backup of settings that i had taken do not seem to want to re-apply.NAP support: So i have tested my NPS (radius) server with NTRadping.exe and all is good, however i cannot get the SGE2010 to talk to it.... the authenticator state in the web interface is always listed as initialising.... im not sure if this is a simple incompatibility (hence the attempt at a firmware upgrade), a tag that needs to be set on the radius side or a switch misconfig.
1) how on earth do you upgrade the firmware?
2) why are none of my settings being saved when the device reboots ?
with TFTP upgrade SRW2xxG4_FW_1.2.3.0.ros and WEB interface after the restart, the switch will not start, display HyperTerminal link. You can also restore the switches do not?
View 1 Replies View RelatedI have downloaded the ros file, but can't find how to apply it. I know this information must be out there, but can't find it.
View 2 Replies View RelatedI am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:
Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
How to regaining control of this supposedly smart switch?
I am trying to update the SGE2000v1.0 with 24ports to 3.0.1.0: url...I got the error "illegal software format" using tftp.
View 2 Replies View RelatedWe have small network with 15 Computers all connected to SRW224G4 . After a power brake our switch dosent "boot" anymore. I see all leds working flashing etc but no network acces, no Serial acces. When i try connecting to serial port and "reset" device the screen is blank.
View 1 Replies View RelatedI need to upgrade WCS firmware. Currently i am running with 7.0.172.0 .
View 1 Replies View RelatedI currently have 3 WAP4410n's (actually, they're WAP4410N-E V02s) that have been really unreliable since I got them - so much so that we've had to cron a restart script on another server which is frankly ridiculous - they've always run firmware version 2.0.2.1.
I've tried updating the firmware to new versions in the past with no success - when I do so, it looks like everything's fine, but when I log back in, the fixed IP address information isn't shown, and the wireless is disabled. I can enable it, but I can't select a channel.
At this point, I have to revert back to the old firmware. I've tried restoring to factory setttings before and after the firmware flash, but this hasn't changed anything.
However, recently I was able to flash firmware 2.0.5.3 onto only one of the routers - it worked fine and all information was displayed and wireless enabled correctly. However on the other two, no matter what I try, the firmware won't upgrade succesfully - it looks like everything's fine, but the fixed IP information isn't shown and wireless/channels are disabled.
I have a Dir-655 A3 with the firmware 1.32NA. I cannot get the new firmware 1.35NA to take. The router seems to go through the motions of the upgrade, but at the end, when I log back on, the firmware still says 1.32NA & all custom settings remain.I have upgraded the firmware on this router before and I know that when its upgraded, the router is basically reset to factory settings. All the settings have been backed up and I am attempting this upgrade via a wired connection.
View 2 Replies View RelatedI have a DIR-655 Rev A4.I followed this forum in the past when there were many problems with firmware upgrades beyon 1.21. Because of this I never upgraded and was told to be satisfied that I can still stay with 1.21 as upgrades caused problems for a number of people.Everything still seems fine with 1.21 except the Shareport utility often does not pickup the printer connection upon booting to Windows Vista. I can always work around this by Disable and then Enable. It will then always find the printer. It is a minor annoyance however.Should I still stay with 1.21 or is upgrading to 1.35 NA recommended ? If I upgrade to 1.35 NA is there a downgrade path back to 1.21 if the upgrade does not work well ?
View 12 Replies View RelatedIt baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies View RelatedI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies View RelatedWe have 2 ASA 5520s in active/standy. We run IOS 8.2(5)24 and I wondered if I need to upgrade as I see the versions have gone to 8.4 and beyond! We are not getting any issues and I'm aware of the difficult migration from 8.2 to 8.4 etc due to the NAT change.
View 3 Replies View RelatedI´ve a problem with my "old" PIX515e device. I wanted to flash this device to a new firmware level but forgot to disable the "lost enable" password before. So I started to make the firmware upgrade on my device, ended up with "flashfs" is busy and I should start the enabled modus and "copy flash tftp" to activate the new flash version. Unfortunalty I cannot do this because I´ve lost my password. When I´m trying to boot this device up now, it will end with a error message...
Unable to locate boot image configuration
Booting first image in flash
No bootable image in flash. Please download an image from a network server in the monitor mode
Failed to find an image to boot
As mentioned, when I will load a new flash image over monitor mode, i cannot activate that image because of flashfs is busy.The password reset bin files will not work too. I tried that too but this one will recongnize no active installed flash.Is there any way to reanimate my PIX515e? In newer devices there are possibilites to work with changing config register but I´ve found nothing about that for a PIX515e.
I cannot find instructions on how to use the latest 4.0.18 ADSL firmware on an 887 router.
I've downloaded adsl_alc_20190_4.0.018.bin from the website and copied it to flash, but cannot find any instructions on applying the firmware. Tried rebooting but made no difference.
What commands, etc, am I meant to use to make use of this ADSL firmware release ?
I've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
After much investigation I finally found what I thought was the firmware upgrade for my WAP4400N access point, I downloaded the file which is a .img file which seems a bit off I think. Anyway when I go to the admin page it decides its an unknown file format. Could someone explain what I am supposed to do with it!
I have to say I am very dissapointed with the whole support function of this site it is very hard to navigate and when you do think you have the correct link, its not. How very helpful!!! I suppose there are networking gurus who look after multi 1000 user systems who understand how the site works and think its fantastic. I support 5 PC's and 7 laptops on top of my normal job, it should be easier.
I've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task). I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link.
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.
Have the DIR-655 Hardware Version A1. Firmware 1.00NA dated Feb 2010. When I try to upload ANY firmware update from the DLINK site, it says that it is not for that device or is corrupt.
View 5 Replies View RelatedI have the DIR-655 . I decided to do a firmware update to Firmware Version: 1.35NA and now I having a problem connecting remotely from outside the network to a computer on my LAN. I use a software called Radmin to connect to one of my LAN computers behind the DIR-655 router and now since I did the update I cannot connect because the router is blocking the request, here is the router log info
[code]...