It is good at times but usually it gets slow and web pages come up with "The web page is taking too long to respond". When I run Diagnose, sometimes I get the computer is correctly configured, but something is wrong with the DNS server (I dont know what that is). I have a NetGear CGD24G Wireless Router that was supplied by Charter when I got internet from them again. I also run Windows 7.
View 12 Replies
Past couple of weeks trying to connect to some websites. It is only SOME, not all websites. It will either say that it is taking too long to connect or that the website is experiencing problems. I have no idea where to start as i am pretty clueless when it comes to configuring/repairing network related issues.
View 3 Replies View RelatedI have an Inspiron 1521 and while I can find and connect to a network easily and quickly; it takes 5 minutes or so for it to really work. My icon says it's "identifying the network". Is there anything I can do to speed up this process?
View 1 Replies View RelatedI've been experiencing problems with internet speeds at my church and my home. They both have security keys, but many people use it. I was wondering - Is there a free tool to monitor who/which device is taking up all of the bandwidth? Something that kind of points out, "Hey, this guy is really slowing you down". Possibly even (But not necessarily) kill their connection?
View 1 Replies View RelatedI have ASA 5510 with CSC-SSM-10 .ASA 5510 IOS version- 8.4.2 and CSC-SSM-10 IOS version 6.6.1162.Web filtering is working fine with respective to my configuration.From yesterday morning, i was facing issue with the sites like gmail, webmail.After giving credentials like username and password in the web page, the page is not resonding.In troubleshooting process, i removed all the acls, class maps which will direct all the traffic towards the CSC. In this scenario all my mail service sites are opening.If we apply the these ACLs and Class-Maps, only my mail service sites only affecting.
View 1 Replies View RelatedI am configuring Clientless SSL VPN on ASA5505 with 8.2(2)17. After the login, default page should be "Home", but if activating "Anyconnect". it always goes to Anyconnect as a first page. If disabling "Anyconnect" using SSL VPN Customization Editor --> Portal --> Application, it always goes to the other one. Never get "Home" as a first page, can I set the first page manually?
View 3 Replies View Relatedi need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen
View 2 Replies View RelatedMobile devices are saturating our medium sized enterprise network. Examples of these devices are iPhones, iPads, Kindles, Droids, etc When a device is authenticated on our APMobile wireless network and downloads updates, email, or music our Network bandwidth is consumed. Services/Applications are no longer available, such as VoIP. Basically, this is an internal DoS.I have done some research and an example of this problem is an ARP Storm but currently clients obtain IP addresses form our DHCP server, which acts as a proxy for the clients and if effective against deliberate attempts to craft packets that create ARP Storm. In addition we configured the WLC to disable ARPunicast processing via the CLI.The following link is from Cisco's site. It is the ARPstorm that we originally thought was the cause but after more researching we found it wasn't this exact issue - http:[url]....why iPhones frequently take down our network? Could this be a configuration issue with our firewall (Cisco ASA 5520 running version 8.4(2))?
View 1 Replies View RelatedWe've recently upgraded our switches from 10/100 over to FOUR Dell 2848 (GB Managed switches) and using one as a director (fiber uplink).We are all on GB networks now and we've been running into issues tracking down what's hogging up most of our bandwidth (local area network) throughout our company.We need to track down which machines are copying data to servers and vise versa.
View 1 Replies View RelatedI installed a tp link extender to boost wifi at home (2 storey) and since then I have noticed that upstairs where the router is installed the signal is weaker than downstairs where the extender is located.
View 2 Replies View RelatedMy old Actiontec M1000 modem recently died and my HP nc6120 with windows XP can not connect to the wireless network through the new Actiontec C1000A model.It connected wirelessly through the old M1000 moden. Window icons on the screen indicate no wireless network is detected. When I view the available networks and log in to the assigned network with its password, it looks like it is trying to connect but does not. It will connect through the ethernet link-up. I don't have any other wireless devices to connect to the network. I have updated the drivers for the wireless card through HP. I have taken the HP nc6120 to the Geek Squad and the wireless card connects with their network. I seem to have a compatibility problem with the old HP with its XP windows operating software and the new modem system. I have tried to reset the ip addresses, but this has had no effect. However, I do have purchased AVG protection software operating on the system, which I am not sure how to shut off. Is this a problem with a too advanced modem for an old style HP with an XP operating system? Is there a modem that I can downgrade to if it is? [code]
View 3 Replies View RelatedMy Multi-media tab is not taking my wireless password? I have a d'link DIR-601; I reset the password using the web interface, but no matter what I try it doesnt link to my tab.What am I doing wrong ?
View 1 Replies View RelatedI have a Cisco 4404 WLC that is up, has green status light, the interfaces are showing activity. I see it connected to my Cisco 6500, (Sh port status) it shows connected and trunking,; I also see a lot of activity on the interfaces. Also it will not let me console in, I can console in on my other Cisco 4404 WLC's with out and issues, so I know my cables and configure are correct. The only change a I made today was the time zone. I noticed the time was off by a hour and noticed that the time zone wasn't set so I set it correctly. Shortly after that I saw the WLC go belly o up in my WCS. I tried rebooting the WLC several times without luck. Since I can not gain access via the console I can not really trouble shoot.
View 10 Replies View RelatedI have a Cisco 876 router, I need to connect ethernet WAN link, While configuring IP address am getting below error.
yourname(config)#int f0yourname(config-if)#ip addres 172.30.1.0 1. 255.255.255.0
% IP addresses may not be configured on L2 links.
I just got digital cable, phone and internet and when I try to use the digital phone and internet at the same time, the internet wouldn't work. Its connected through Netgear N300. The wireless connection will not stay connected.
View 1 Replies View RelatedI have removed all port forwarding and enabled DMZ? I made sure the DMZ IP matches my internal IP. DMZ still not taking effect. One thing I noticed is that when I visited [URL] it showed a different IP then what was assigned to my router itself.
Modem > Linksys Wireless > Computer
Should the Linksys Wireless be in gateway or router mode?
i back up my very important server 2008 r2 data over a vpn to another computerall together its just under 5GB...it used to take 5 to 7 hoursnow the same data is taking 14 to 24hours...why would this be?im using netgear vfs338 vpn firewalls at each end
View 12 Replies View RelatedAbout a week ago, our network started to experience complete failure.
Our Equipment:
Router: Netgear FVS336.xxx
Switch: Dlink DES-1024D (we have 6 of these switches in our building)
Wifi Routers: Dlink DIR-601, Linksys wrt54g, wrt54gv2
Computersservers: 40x
Copiersfax: 5x
Wireless clients: (iphones, laptops) at least 30
All has been working together in harmony for many years.Fast forward to last week when my hell began with intermittent crashes.Not sure what's causing the problem.When it happens, everybody loses their internet, the ability to communicate over the network; ping tests won't respond to anything (including the router) that exists on the lan, even with a static IP against other statics.In visually inspection of the switches and router, they seem to be happily blinking away with no apparent issue (visually).The only way I've been able to fix the problem is by power cycling the router.About 1 second after doing that, we're back in action for 2-6 hours (very unpredictable).I never had to power cycle any other devices)
Steps I've taken in troubleshootingeliminating potential culprits:
Replaced the router with a spare (new) FVS318G
Replaced the power supply for the router (suspected because problem remained after router swap)
Replaced cable going from router to lan switch
Removed linksys wifi router from network (the router had needed power cycling weekly and was old. So I unplugged it)
Removed Dlink wifi router from network (I hate dlink routers, so removed it).I'm at a loss.
I have a Dell laptop running Windows 7. The problem is that every single time I try to connect to any wireless network, I get a message that says "Connecting to the network is taking longer than usual."The network almost always connects eventually (about 2 minutes), and once connected there doesn't seem to be any other problem.This has been going on for about 2.5 months. It began shortly after I restored the laptop to factory default.
View 11 Replies View RelatedI have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
I have an ASA 5510 and two IPS connections. I need ISP2 to take over when ISP1 does not respond. I have followed the following link ASA/PIX 7.x: Redundant or Backup ISP Links Configuration Example and as far as i can see this part is working. I disable interface for ISP1 and the routing table changes its static route to ISP2. When i enable ISP1 again the static route changes to ISP1. However no traffic flows to the outside. I have set up a nat rule that is the same as for wan1.
View 10 Replies View RelatedCisco 851 router Apple Ipad 3 using IPSEC setp get this message The VPN server did not respond. I have tried Anyconnect that gives me Cannot verify server identity anyconnect can't verify the identity of ios-self-signed-certificate-1164042433 would you like to continue anyway? hit continue and it just goes off. I was asking if If get an ASA 5505 to replace my 851 it would work in my environment.
I have 15 computers accessing the web thru the 851. I host a web site on one of my servers. I have a static ip address. I also host exchange server and have remote web access to my exchange as well as remote outlook users. I can VPN thru the 851 using the cisco client on Windows 7 and vista and even xp. Would like to use the native windows client and get my iphones and ipads working. Can the ASA5505 support the above? Was also looking at the cisco 1841 how about that one?
So I have a current port-channel between two 6ks that I need to upgrade. There's too much traffic and the port buffers on the SUP7203B sort of suck. Microbursts are causing overruns like mad. Im going to move the 2x1gig port-channel to a 6724 and make it a 3x1gig port-channel. The switches carry production traffic across the link to the tune of about 400 meg during the lowest load time. Initially, I thought that I couldn't move the port channel without temporarily taking down the link but I think I have a workable solution now. Has anyone done this successfully before? Im curious what others have done. Also, to make matters worse, the existing port-channel is 'mode on' and I want to migrate to 'mode active' in the new channel
View 7 Replies View RelatedI have an HP Pavilion wireless laptop with windows vista and a gateway desktop, windows XP Home edition and every thing worked ok untill I got a virus on my desktop Since then I've formated the hard disks and reloaded the opering systems, but I don't know how to get the laptop working wirelessly without taking the motorola modem and connecting it directly to the laptop, I have a D-Link DIR-615 router.
View 4 Replies View RelatedI have several windows 2003 virtualized on linux + kvm envirorment.One of them has a strange and unpredictable behaviour: windows 2003 network stop to work.Suddenly it's not possible to ping it. The services are not reachable.Usually it's enough to disable the network card and enable it again.At first I thought something about virtualization but there is another windows 2003 on the same server, with a network card on the same bridge, using the same drivers.
View 1 Replies View RelatedIn each case, the routers have functioned flawlessly for a period of 2 to 8 months, then suddenly begin to require daily to hourly reboots to keep the speed up, and often times fail to respond to any web activity whatsoever. Ping tests are intermittent, sometimes failing but other times succeeding while web sites remain unresponsiveFor three years I lived with two or more room mates at a time, each of us with our own computer (or 2) and all doing a lot of peer to peer downloading. I realize a router can overheat during heavy use like this, so buying new routers so regularly has seemed vaguely understandable. However it doesn't seem like that is the case in my most recent failure.I've lived alone for the past 3 months, and have owned the Belkin Play Max N600 HD since. I have NOT been P2P downloading or putting a heavy load on my router in any way (or so it seems). Yet as of about two weeks ago, it has suffered a major slowdown just like all of its predecessors. Yet my 30 mbps internet connection roars to life the moment I plug the modem directly into a computer.
My desktop remains on 24/7 but like I said before, I do not do constantdownloading/uploading. Both wired and wireless connections are effected equally, and I have always kept all my routers WPA encrypted.When websites become unresponsive on my Belkin today, it is usually after everything has been sitting idle for some time (overnight, or all day while I am at work). Speaking of work, today is a perfect exampleI remoted into my home desktop and was able to interact just fine, yet when I would launch a browser and try to load any website at all, I get absolutely nothing. I had to transfer a text document through DropBox (which also still worked) because I couldn't get Google Docs (or gmail) to load on the remote computer
SGE2010P won't Switch respond to login after reboot
View 1 Replies View RelatedI've inherited a 7206VXR router and it takes very long to boot. It outputs READonly ROMMON initialized to the console and 14 minutes later it continues the boot process. After 17+ minutes the boot is complete with the correct full image. The processing engine I have is the NPE-G1 and I'm looking for an upgradeable ROMMON image or a reason why the boot is taking this long.
View 1 Replies View RelatedI hope an easy question, in the WAN profile of our SA540 I have IP Aliases configured for a block of IP addresses we have. The active 2 IP addresses plugged into the actual RoadRunner modem respond fine to ping, the other three I have programmed to the WAN interface are not responding as I would think they should. Have I overlooked something? The "Block IP on WAN Interface" is disabled and pings back fine.
View 3 Replies View RelatedI'm trying to set up an 802.1 q trunk between my layer 3 switch and ASA5520. I understand I need to create a subinterface to accomplish this and have done so. However, the subinterface does not respond to pings, and when I attempt to run the packet tracer on the firewall itself, I get a message saying Flow is denied by configured rule. But the strange thing is it shows the output interface as "np identity ifc":
(The VLAN in question is VLAN2 192.168.2.3 is the VLAN2 address on the switch). The ASA config is as follows:
ASA Version 8.2(5) <context>
hostname context2
names
!
interface GigabitEthernet0/0.2
nameif Inside0/0.2
[Code] ....
I've been using my 2509 router as an access server for my 3 routers, 1 frame-relay (3640) and 4 switches for the past 2 months and it work great till this morning. As soon as the async lights on when i try to connect, it just hangs. It doesn’t respond to anything. No key hits not even disconnecting the console to where im connecting too. (from router to router) if i reboot the router with out the cord plug in (the async) i can use the router with all functions working great; But as soon as i connect the async cord.
The lights blink and poof router is gone. No response. i just cant figure how from one day to the next it doesn’t work.I haven't tried a different cable yet but i tried disconnecting all console connection and just left the plug in and boot. This works but as soon as i connect to any console port physically it gone. No response?i cleared all my configes and its blank and it still just doesn’t respond as soon as i connect any thing (after configuring all the basic)
ive tried these
line 1 8
no flush-at-activation
no login local
no modem Dialin
no exec
speed 9600
still no good?
Upgraded LMS to 4.1. Yep basically reinstalled. However I can't remember how I did a couple of thing on the original system.
I am trying to take the traps from the Cisco equipment to the LMS and generate e-mail. How do I take the incoming traps (Crit and Warning) and send an e-mail alarm. I'll plan to control what to trap on at the Cisco Equipment.
SNMP trap is set from a fan fault, the Cisco send a trap to the LMS. Now I want take that trap and forward via an email.
I have been reading the admin documentation on "Notification and Action Setting". I see how to take the Cisco LMS created trap and email alarm. (In this case I need a specific trap that LMS did not have.) I see how to take Cisco Traps and resend them to other NMS.
I work on a college campus that has thousands of students a day accessing our wireless network. We have broadcast SSID that the students use to connect to the internet. The students usually have more than one WiFi enable device on them and their laptops and phones both take an IP address, but they are only using the laptop to authenticate while the phone is associted, but not authenticated. In the meantime, I have several thousand IPs being used by their phones/iPods etc. Is there a way to revoke the DHCP lease if the client does not authenticate within a specified time frame (i.e. 10 minutes)?
View 3 Replies View Related
