Cisco Switching/Routing :: 2960 / TNSWAGCS01002 / ARP Incomplete Entry
Dec 26, 2011
I plugged an IP device into a 2960 Catalyst switch. The port is up, but there is no MAC address learned on it:
TNSWAGCS01002(config-if)#do sh mac add int fa0/16
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
TNSWAGCS01002(config-if)#
TNSWAGCS01002(config-if)#do sh int fa0/16
FastEthernet0/16 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0064.40ee.f510 (bia 0064.40ee.f510)
Description: --- STC ---
[code]....
I read that it may be a L1/L2 issue. We tried with another ethernet cable. We also tried with another IP device of the same model. That did not solve the issue.
View 2 Replies
ADVERTISEMENT
Jul 1, 2012
Thinking of getting one of those 8-port 2960 for a CCNP study. Is the difference between the C2960-8TC-S and the C2960-8TC-L models in Hardware, or in IOS? or both? And if it's in IOS, is the S upgradable to L?
View 7 Replies
View Related
Sep 25, 2012
We have a site and on that site we have a server which is down form last two days. However , to manage these devices we are not using any tools. We are not able to find this server that where it is located and on which switch it is connected to.
I want to know that the timer for mac address is 5 minutes and arp timeout is 4 hours . Is there any way to find out the mac address of the server . I feel like this can we done with cef ? Is it true or not I am not sure. I am running 3750 stacks and 2811 routers. 3750 stacks are working as layer 3 devices. They are also running the pretty new IOS 12.2(53)SE.
According to my understanding now a days CEF entry does not expire if we are not using them. They remain in cache as we are running with destination base CEF.
View 4 Replies
View Related
Dec 3, 2012
We have a pair of 6509's with duplicate ACL lists & entries.
1 = Version 12.2(33)SXI4a
2 = Version 12.2(18)SXF15a
I wanted to remove some logging that was on an entry on one of our extended ACL's. On 1 this worked fine with the no 400
400 <acl rule without log>
However on 2 it lets me carry out the no 400 command but when i go to add the 400 <acl rule without log> i get the error % Duplicate sequence number.sure enough when i perform the 'Show access-lists <Name>' it is still there!
I have tried the following:
Adding a duplicate ACL entry before it (399) without log and i still get hits on line 400Adding and removing the duplicate created line 399 (without logging) with no issues.Adding and removing a dupliacte ACL (without Logging) after (line 401) with no issues
It looks like it is just this line it seems to think it has removed but hasn't?!
I understand an option is to duplicate the ACL in a text editor remove line, delete the ACL and put the edit back in .....however i wondered if this is something known (bug).
View 11 Replies
View Related
Aug 19, 2011
Does PBR with deny ACL entries on a 3750 are still punted to the CPU? I found this article: URL
High CPU Due to Policy Based RoutingPolicy Based Routing (PBR) implementation in Cisco Catalyst 3750 switches has some limitations. If these restrictions are not followed, it can cause high CPU utilization. You can enable PBR on a routed port or an SVI. The switch does not support route-map deny statements for PBR. Multicast traffic is not policy-routed. PBR applies only to unicast traffic. Do not match ACLs that permit packets destined for a local address. PBR forwards these packets, which can cause ping or Telnet failure or route protocol flapping.
Do not match ACLs with deny ACEs. Packets that match a deny ACE are sent to the CPU, which can cause high CPU utilization.
In order to use PBR, you must first enable the routing template with the sdm prefer routing global configuration command. PBR is not supported with the VLAN or default template
I checked the latest config guide, and those same guidelines are still listed. If that limitation is still there, are those packets switched at the process level (ip_input) or the interrupt level?
View 8 Replies
View Related
Feb 7, 2012
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
Dec 4, 2011
I have some error messages in the Nexus 7000 log, after searching i cannot find an adequate explanation, pretty much the only thing i can find is below and i don’t think it is very relevant to my situation. The device is in production and so reloading and pulling card willy nilly is the last resort.
Device = Nexus 7018
IOS version = 5.1(2)
Log messages=
2011 Dec 2 14:52:35 IAS01LVSWIPC01 %OC_USD-SLOT8-2-RF_CRC: OC2 received packets with CRC error from MOD 6 through XBAR slot 1/inst 1 and slot 2/inst 1 and slot 3/inst 1
[code]....
View 3 Replies
View Related
Oct 30, 2011
I have configured a new switch 3560 switch and connected to 4500 switch and formed a trunk connectivity.Now the issue i am facing is when i do a SH CDP NEIGHBOUR from 3560 switch i am able so see 4500 swries switch but at the same time when i do SH CDP NEIGHBOUR form 4500 series switch i am not able to see the entry for 3560 switch.But i am able to telnet the new switch with out any issues
View 11 Replies
View Related
Feb 2, 2009
Is there any way to clear a single ARP cache entry on the 6500 switch ?
View 8 Replies
View Related
May 23, 2012
I have seen other discussions regarding Static MAC address entries on IPv4, but what of IPv6?We have MS NLB solutions and they are working fine. We have Cisco 6509/6504, Version 12.2(33)SXI5
But then we have a new one for a new ActiveDirectory solution, and on those networks we have implemented IPv6.
How is Static MAC address entries and MS NLB solved in IPv6 (i.e arp ip.ip.ip.ip mac.mac.mac ARPA gi1/1). I can't seem to find much examples or documentation on this? Is it replaced with another function?The reason I ask is twofold.
1. I really want to know
2. The NLB cluster seem to drop IPv6 traffic at even intervals, witch seems to correspond with NLB transition.
View 1 Replies
View Related
Dec 22, 2011
The issue is occuring on our local LAN where my ARP requests are being modified after a period of time by the router for one host. I'm finding that the host will work fine with the correct MAC IP pairing for a period of time and then about 15-30 minutes later, the arp table is changing so the associated mac/IP address is now the mac address of the router interface.
The FastEthernet 0/1 port has no ip proxy-arp enabled and is set with ip nat inside.This only started happening after restarting the router, however the running config was saved as the startup config prior to the restart.I've tried hard-coding the entry with the command arp 10.15.4.190 c82a.1459.0579 ARPA however that is not working as expected.
The device is an 1841 ISR with the advanced IP Services bundle loaded. Is there some way that the router is viewing my host (provides DNS, Directory Services) as a intrustion attempt and somehow rejecting the packets?
View 1 Replies
View Related
Nov 3, 2011
In my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
View 2 Replies
View Related
Mar 14, 2013
I need a switch to configure a static ARP entry for a MS NLB multicast.
Could answer me if I can do with the SRW2024-K9-BR?
View 4 Replies
View Related
Aug 23, 2009
Aug 24 11:32:16.275 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to down
Aug 24 11:32:36.827 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to up
Aug 24 11:35:23.854 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/2, changed state to down
Aug 24 11:35:24.854 AEST: %LINK-3-UPDOWN: Interface FastEthernet0/1/2, changed state to downesw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)(code)
When the above problem happens, as work-around, we delete VLAN.DAT file on the Compact Flash of this 2811 router and recopy the VLAN>DAT file back to teh Compact Flash.
Then it runs for a few weeks and the same problem happened.
Then we put a new Compact Flash and recopied VLAN.DAT to new CF and it ran for 3 weeks and same problem started again.
Could be 2811 router motherboard? This customer has thousands of these 2811 routers in identical setups and this is the only router that is having this problem.
View 6 Replies
View Related
Mar 17, 2013
If a router receives EIGRP (AD90) routes, and is configured to redistribute thoes routes into BGP(AD20), why does the RIB show only the incoming EIGRP routes and not the redistributed bgp routes? Are redistributed routes considered for RIB entry in the router that is doing the redistribution
View 2 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
Dec 26, 2012
I'm having a strange problem where I'm not able to get through a Cisco 2960-S L2 switch when connected through vpn, while LAN-WAN traffic is working fine.The situation on site is the following:When inside the network I'm able to get to the internet without a problem. The problem is within a vpn-session. When this session is succesfully started I can ping and manage the Cisco 2960-S switch, but I can't ping or manage the Dell switch from my laptop. I can however ping the Dell from the Cisco-switch. [code]
View 7 Replies
View Related
May 15, 2012
set up my QoS on two 2960
-------------------- ------- ------- ------------
PBX Asterisk |----|2960-1 |------|2960-2 |-----|Voip client2|
-------------------- ------- ------- ------------
-------------- |
[Code].....
This will be this configuration for all input interface right ? For the Output part I'm lost, what do I have to do ? And for the 2960-2 do I have to put the same configuration ?
View 5 Replies
View Related
Nov 7, 2012
we hava a couple of 2960 switches and we are logging to a syslog server. Ports keep going up and down is it normal severity (error) ?
View 2 Replies
View Related
Feb 23, 2012
We recently updated a site2site link to metro ethernet, ISP call it 100mbps LAN Extension, but to me it is just QinQ over fibre connection. Most went well, one thing (annoying to me) is we can not ping our switches on both ends anymore.
We have a 3750 in headend and another 2960 on the other end. I used to be able to ping/telnet to the management IP from one to the other. Now we can not. I think the ISP is applying some configuration on ports of their customer-premises equipments (both are Cisco switches) but agent in ISP told me no. I thought there is some configuration on Cisco switch to block "MAC discovery" but i just can not remmenber what was that and google also failed me this time.
View 3 Replies
View Related
Apr 20, 2013
I have got two links from the same ISP, primary and secondary and connected to two different switch. The ISP have passed the trunk vlan of 30, 31 and 32 on both of the links. The ISP can't provide stp. I have got another managed 2960 series switch. How can I obtain failover on switch level.
View 2 Replies
View Related
Feb 21, 2013
I have IP phones connected to 2960 i want to segregate traffic traffic comming from IP phones which has a COS value of 5 and want to allocate a band width of 200 MBPS for those traffic .
Can any one share sample QOS configuration for achiving this in 2960 ?
View 2 Replies
View Related
Mar 10, 2012
My cisco ios 2960S is crashed and the ios is gone The issue is i am connecting my pc to management port and i give switch:
IP_ADDR x.x.x.x/255.255.255.0 and also switch: DEFAULT-ROUTER
But i can not copy tftp to flash,according that i have L3 port (management) why should i use xmodem?
View 3 Replies
View Related
Mar 16, 2012
I have 2 switches connected Via MM fiber cable one of them SRW2024-K9-NA with MGBSX1 Transceiver and the Secand One 2960 with GLC-SX-MM
are there is any configration must be done or not ?
View 2 Replies
View Related
Jul 22, 2012
Have Cisco catalyst 2960 IOS ver12.2(53)se2 when power on the power LED does not come up and on this is what shown on hyper terminal. what need to be done for this switch ?
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: b4:d9:8d:27:4c:00
Xmodem file system is available.
[code]......
Interrupt within 5 seconds to abort boot process. Boot process failed. The system is unable to boot automatically. The BOOT environment variable needs to be set to a boot able image.
View 12 Replies
View Related
Jul 2, 2012
I currently have a network with (8) 2960 Cisco Switches. (6) of the 2960 switches are etherchanneled back to (2) 2960 switches in the computer room. I would like to setup QOS on the (8) switches, however the traffic is very differnt on each of the switches. I have video, ip phone, server, printer, PC traffic. I am not sure what the best method of separating this traffic into differnt QOS queues.
View 3 Replies
View Related
Jan 6, 2012
we have a cisco 2960 48 port tcl switch port and i've enable ssh on my switch and now :
1) how can i login to ssh ? how should create username for ssh ?
2) how can i disable telnet ?
3) how can i change main (master) password?
View 7 Replies
View Related
Jun 4, 2012
I have an switch 2960 and i have made an SSH connection . But the problem is that whenever i try to open with my teraterm or putty it ask for username and after that password but does take the password. It shows an error of password what should be the problem.
Commands that i entered to make SSH
config# username admin password pankaj
config# ip domain-name home.local
config# crypto key generate rsa
config# 1024
config# ip ssh version 2
View 6 Replies
View Related
Jun 4, 2012
I have an switch 2960 and i have made an SSH connection . But the problem is that whenever i try to open with my teraterm or putty it ask for username and after that password but does take the password. It shows an error of password what should be the problem.
View 1 Replies
View Related
