we have a cisco 2960 48 port tcl switch port and i've enable ssh on my switch and now :
1) how can i login to ssh ? how should create username for ssh ?
2) how can i disable telnet ?
3) how can i change main (master) password?
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedI have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies View Relatedi have 2960 Catalyst with LANLITE. And i cannot set "transport input ssh", it allows only telnet. I'm wondering if cisco lanlite switches have ssh input in newer releases of IOS or there is no way to make ssh input on this switch?Here's show ver output (i removed all serial and part numbers):
S14#sh ver
Cisco IOS Software, C2960 Software (C2960-LANLITE-M), Version 12.2(37)EY, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 28-Jun-07 18:07 by antonino
Image text-base: 0x00003000, data-base: 0x00D00000
[code]....
I have a very problematic situation here.I have configure on a Cisco 2960 the vty line in a wrong manner and now I am stock.To configure those vty to enable ssh I have typed :
line vty 0 4
login local
password xxxx
line vty 5 15
login local
password xxxx
exit
Problem, I work remotely (I was on telnet while doing this). I have no username configure as I thought that root user would work.Now when I issue an ssh to my switch, I always failed authentication.how I could recover access to my switch without being physically there ? I have write the config in memory, otherwise it would have been too easy.
I configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
lets you catalyst 3560 & 2960 remote login with a secure protocol
View 4 Replies View RelatedI have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
I have just set up my Cisco 1941 router to my cable internet connection. I have access to everything, but I cant login successfully into Cisco CP.
I set up a new user with level 15 privileges and a secret password. I go to login via webbrowser and I put in my credentials, but I get rejected. I have tested the username and password via the CLI, and it works fine, I just cant seam to login to Cisco CP.
I can access to Cisco 3750 with SSH, but fail to login to web http with the same login.I am able to get the login prompt, the login error I get is "The server at level_15_access requires a username and password."Below is my switch config:username admin privilege 15 secret 5 $1$xsdfajiwuoeirlkajsd.
View 1 Replies View RelatedWe have two 6500 switches and I am unable to login to these switches anymore, but i was able to connect to them yesterday via Telnet. The strange part is that it happened for both switches at the same time.But now when i try to login, it gives me a message "password required, but none set". I can login to them via console.Is it because the 0 - 4 VTY connection are being used and there is no password set from VTY 5 to 15?The config has not changed.
SWITCH-1
line con 0
exec-timeout 0 0
password xxxxx
login
line vty 0 4
[code]....
my ASA 5505 just woke up one day and didnt allow me to login to it with ASDM. i can console in though but telnet, ssh and asdm will not work. it just times out.
View 4 Replies View RelatedMy management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View RelatedI have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
I have recently aquired a Cisco SGE2000 switch and the first thing I did was update to the latest firmware and change password. Now I cant login? Neither my admin / admin dosent work nor the new user I have created. Is there any characters that this dosesnt support like backslashes or forward slashes for password? If not then what can I do to get access to the switch again?
View 2 Replies View RelatedI have a brand new 1921 router that I can't login to using cisco/cisco. Is there a new password?
[URL]
I don't have physical access so I can't reboot it until Monday. Just wanted to get it working today.
I have my first 3560x running IOS 15.0(1)SE and noticed that I can no longer login to privilege mode even though my use account is setup with privilege 15. I have the exact same setup on 12.2 (53)SE2 and have no issue, so has something changed?
View 4 Replies View RelatedI am planning on having a contractor in to configure some new routers and would like for him to login using the local account on the routers while company personal continues to use radius is this possible.
View 6 Replies View RelatedI have a 3560-X switch and want to access it through GUI. what image I need to download and steps to use GUI(Just like ASDM for ASA 5500 series Firewall).
View 1 Replies View RelatedDoes the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View Relatedive updated my catalyst 4948-10GE to version 15.0(2)SG1.Now it is not possible to login by ssh or telnet on this switch. the access is established over the mgmt-Interface and vrf.i get a ping reply but login is no more possible now.is there an new feature in this version for vrf or remotelogin that has to be configured? if neccessary i can paste the running-config here.
View 3 Replies View RelatedWe created some local account for this switch but we unable to login when the TACACS Server down.
3750 Switch
aaa group server tacacs+ ACS
server x.x.x.x
server x.x.x.x
ip vrf forwarding Mgmt
ip tacacs source-interface GigabitEthernet0
[code]....
I have a customers Catalsyt 2950 switch come in for the configuration to be cleaned to factoy default, using the link below removed the customers banner and login information whitch worked
[URL]
When i restart the switch and enter Enable mode I'm prompted with the password which i used when following the link above,
I want to remove all passwords so when the switch is redeployed to the next site who ever the engineer is that is going to be reconfiguring the switch is able to access privlage mode with out the password promt.
I'm having trouble with a Cisco Catalyst 2950 Series Switch where by I'm following the procedure from Cisco's web site to remove the Banner and login information, url..
Each command is being accepted by the switch from following the information given within the help sheet above,the problem i have now is when i turn the power off then turn the switch back on I'm still getting the banner and login information even though i have follwed Cisco's help correctly.
I'm having a strange problem where I'm not able to get through a Cisco 2960-S L2 switch when connected through vpn, while LAN-WAN traffic is working fine.The situation on site is the following:When inside the network I'm able to get to the internet without a problem. The problem is within a vpn-session. When this session is succesfully started I can ping and manage the Cisco 2960-S switch, but I can't ping or manage the Dell switch from my laptop. I can however ping the Dell from the Cisco-switch. [code]
View 7 Replies View Relatedset up my QoS on two 2960
-------------------- ------- ------- ------------
PBX Asterisk |----|2960-1 |------|2960-2 |-----|Voip client2|
-------------------- ------- ------- ------------
-------------- |
[Code].....
This will be this configuration for all input interface right ? For the Output part I'm lost, what do I have to do ? And for the 2960-2 do I have to put the same configuration ?
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies View RelatedIn my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
I´ve a little problem with the aaa authentication over RADIUS with a Cisco 3560G-48PS - IOS 12.2(58)SE2. When I try to log in to the Switch per Telnet, it didn`t works and my windows domain account is locked. Here the aaa config:
aaa new-model
aaa authentication login default local group radius
aaa authorization config-commands
[Code].....
we hava a couple of 2960 switches and we are logging to a syslog server. Ports keep going up and down is it normal severity (error) ?
View 2 Replies View Related