I have recently aquired a Cisco SGE2000 switch and the first thing I did was update to the latest firmware and change password. Now I cant login? Neither my admin / admin dosent work nor the new user I have created. Is there any characters that this dosesnt support like backslashes or forward slashes for password? If not then what can I do to get access to the switch again?
View 2 RepliesI'm having trouble getting a stack of three sge2000 switches to connect together and NOT reboot.Two of the switches are older Linksys sge2000s and they stack well together, but as soon as i connect the new Cisco sge2000, it will make them both reboot sequentially, even though it detects that it needs to be #3 in the stack.SW 1 port 24 is connected to SW 2 port 12 and they function correctly (both of the linksys switches). The documentation states they should be connected in a ring topology so I first tried completing the loop with SW3 (the newer cisco sge2000). When that had the aforementioned troubles I just connected SW2 port 24 to SW3 port 12. Still forcing the switches to reboot.I SUSPECT it may be a firmware/software issue, but I wanted to check if they'ed even work together.
View 2 Replies View RelatedI am running 9.11 and I have created users with password but it has no effect on the SSH Login!I don't get it... What am I missing?
View 3 Replies View RelatedAs observed ACS 5.x " Change Password on Next Login" Feature does not work with SSH Clients ( tried with X-sheel, Secure CRT, Putty etc...) , however through telnet session to IOS devices, users can change their password on their next login.
1: on ACS 5.x i create a new user & Set " Change password on NExt Login" option.
2: Logged into the device through Telnet & Password can be changed after i authenticate successfully. however the same is not happening when i login to the devices through SSH.
is it because of the fact that SSH is encrypted session ?
Because changing password through a telnet session is not accepted in many fanancial organizations as per PCI Standard.
I have a customers Catalsyt 2950 switch come in for the configuration to be cleaned to factoy default, using the link below removed the customers banner and login information whitch worked
[URL]
When i restart the switch and enter Enable mode I'm prompted with the password which i used when following the link above,
I want to remove all passwords so when the switch is redeployed to the next site who ever the engineer is that is going to be reconfiguring the switch is able to access privlage mode with out the password promt.
I recently configured a cisco 3750 switch for a stand alone network here at work, and on all our other switches and routers we use ACS to access everything. This switch being a stand alone I dont have that option.
So being like that I have to create everyone in the shop a username and password. Is there a way to prompt the user to change their password on their first login like you would with windows or such?
Im planning for a network upgrade.77.110.87.112/28 - is assigned to selected users and configured manually.(note: they are public IP which our ISP assigned)192.168.1.0/24 - is assigned to users that are not allowed to use internet services and configured manually. I have CISCO 1841 Router connected to the internet and CISCO SGE2000-G5 24ports layer 3 switch that is connected to cisco 1841 router.i want to create vlan in layer 3 switch. [code] i want all vlans would still ping to each other and file/printer sharing is available.kindly check if my network upgrade plan is correct, how am i going to configure those vlan in my layer 3 switch and to connect to the internet.
View 12 Replies View RelatedI have recently purchased a a Cisco SGE2000 switch and when connected to it via console cable, I was introduced to "Switch main menu" which was kind of a GUI interface. I found a way of accessing what is called a lightweight CLI (lcli).After having a few searches on google it turns out that this switch doesn't have a proper CLI. Is this possible at all? I thought that all managed switches have CLI?
View 2 Replies View RelatedWe have a couple of cisco SGE switches connected to a single DELL, between the cisco switches we have a trunk interface. I'm not sure which setting should be configured on the switches to get it working because a loop is occuring.
View 1 Replies View RelatedI just want the switch to be quiet so that I can perform some network testing with only the connected hosts showing up in my traffic analysis program. But every 30 seconds or so the switch sends out an LLDP packet. This switch is only used in the lab for running tests so I know I don't need the LLDP feature running.
This article explains how to disable LLDP globally on a Catalyst switch, but I can't find any option to disable LLDP in the SGE2000's configuration menus.
We've been trying to monitor the used bandwidth of our SGE2000 and SGE2010 switches with Nagios.We've been experimenting with the various OIDs and we've found the OIDs linked to the different switchports.
Though when we use SNMPWalk (to find the OIDs connected to the port) the names of the ports are all the same.
[code]....
Is there a way to change the names of these interface to unique names?We've already given unique names in the description field through the switch's GUI, but it doesn't make any difference for Nagios.
I was handed two SGE2000 24-port 10/100/1000 switches. The default IP address does not work on either of them. Short of doing a hardware reset, is there an IP discovery utility that I can run.how I can find the IP?
View 5 Replies View RelatedI have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies View Relatedthe following information before:
Switch: WS-C3750X-48P (Stack with 2 Members)
IOS: 12.2(58)SE2
Lic: IPBASEK9
[Code]....
Since i added another Member to the Stack, i'm facing the following problem: When i login with my tacacs user account, i will not be asked for the password. The same thing is for the tacacs account of my colleague, after entering the username he is logged in. It seems for me, that the passwords are cached only for this Switch.
I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
I have just set up my Cisco 1941 router to my cable internet connection. I have access to everything, but I cant login successfully into Cisco CP.
I set up a new user with level 15 privileges and a secret password. I go to login via webbrowser and I put in my credentials, but I get rejected. I have tested the username and password via the CLI, and it works fine, I just cant seam to login to Cisco CP.
we have a cisco 2960 48 port tcl switch port and i've enable ssh on my switch and now :
1) how can i login to ssh ? how should create username for ssh ?
2) how can i disable telnet ?
3) how can i change main (master) password?
I can access to Cisco 3750 with SSH, but fail to login to web http with the same login.I am able to get the login prompt, the login error I get is "The server at level_15_access requires a username and password."Below is my switch config:username admin privilege 15 secret 5 $1$xsdfajiwuoeirlkajsd.
View 1 Replies View RelatedWe have two 6500 switches and I am unable to login to these switches anymore, but i was able to connect to them yesterday via Telnet. The strange part is that it happened for both switches at the same time.But now when i try to login, it gives me a message "password required, but none set". I can login to them via console.Is it because the 0 - 4 VTY connection are being used and there is no password set from VTY 5 to 15?The config has not changed.
SWITCH-1
line con 0
exec-timeout 0 0
password xxxxx
login
line vty 0 4
[code]....
my ASA 5505 just woke up one day and didnt allow me to login to it with ASDM. i can console in though but telnet, ssh and asdm will not work. it just times out.
View 4 Replies View RelatedI have a brand new 1921 router that I can't login to using cisco/cisco. Is there a new password?
[URL]
I don't have physical access so I can't reboot it until Monday. Just wanted to get it working today.
I have my first 3560x running IOS 15.0(1)SE and noticed that I can no longer login to privilege mode even though my use account is setup with privilege 15. I have the exact same setup on 12.2 (53)SE2 and have no issue, so has something changed?
View 4 Replies View RelatedI am planning on having a contractor in to configure some new routers and would like for him to login using the local account on the routers while company personal continues to use radius is this possible.
View 6 Replies View RelatedI have a 3560-X switch and want to access it through GUI. what image I need to download and steps to use GUI(Just like ASDM for ASA 5500 series Firewall).
View 1 Replies View Relatedive updated my catalyst 4948-10GE to version 15.0(2)SG1.Now it is not possible to login by ssh or telnet on this switch. the access is established over the mgmt-Interface and vrf.i get a ping reply but login is no more possible now.is there an new feature in this version for vrf or remotelogin that has to be configured? if neccessary i can paste the running-config here.
View 3 Replies View RelatedWe created some local account for this switch but we unable to login when the TACACS Server down.
3750 Switch
aaa group server tacacs+ ACS
server x.x.x.x
server x.x.x.x
ip vrf forwarding Mgmt
ip tacacs source-interface GigabitEthernet0
[code]....
I'm having trouble with a Cisco Catalyst 2950 Series Switch where by I'm following the procedure from Cisco's web site to remove the Banner and login information, url..
Each command is being accepted by the switch from following the information given within the help sheet above,the problem i have now is when i turn the power off then turn the switch back on I'm still getting the banner and login information even though i have follwed Cisco's help correctly.
I need to reset my login password
View 3 Replies View RelatedI have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies View RelatedIn my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
I´ve a little problem with the aaa authentication over RADIUS with a Cisco 3560G-48PS - IOS 12.2(58)SE2. When I try to log in to the Switch per Telnet, it didn`t works and my windows domain account is locked. Here the aaa config:
aaa new-model
aaa authentication login default local group radius
aaa authorization config-commands
[Code].....