I have recently purchased a a Cisco SGE2000 switch and when connected to it via console cable, I was introduced to "Switch main menu" which was kind of a GUI interface. I found a way of accessing what is called a lightweight CLI (lcli).After having a few searches on google it turns out that this switch doesn't have a proper CLI. Is this possible at all? I thought that all managed switches have CLI?
View 2 RepliesI'm having trouble getting a stack of three sge2000 switches to connect together and NOT reboot.Two of the switches are older Linksys sge2000s and they stack well together, but as soon as i connect the new Cisco sge2000, it will make them both reboot sequentially, even though it detects that it needs to be #3 in the stack.SW 1 port 24 is connected to SW 2 port 12 and they function correctly (both of the linksys switches). The documentation states they should be connected in a ring topology so I first tried completing the loop with SW3 (the newer cisco sge2000). When that had the aforementioned troubles I just connected SW2 port 24 to SW3 port 12. Still forcing the switches to reboot.I SUSPECT it may be a firmware/software issue, but I wanted to check if they'ed even work together.
View 2 Replies View RelatedI just want the switch to be quiet so that I can perform some network testing with only the connected hosts showing up in my traffic analysis program. But every 30 seconds or so the switch sends out an LLDP packet. This switch is only used in the lab for running tests so I know I don't need the LLDP feature running.
This article explains how to disable LLDP globally on a Catalyst switch, but I can't find any option to disable LLDP in the SGE2000's configuration menus.
I was handed two SGE2000 24-port 10/100/1000 switches. The default IP address does not work on either of them. Short of doing a hardware reset, is there an IP discovery utility that I can run.how I can find the IP?
View 5 Replies View RelatedIm planning for a network upgrade.77.110.87.112/28 - is assigned to selected users and configured manually.(note: they are public IP which our ISP assigned)192.168.1.0/24 - is assigned to users that are not allowed to use internet services and configured manually. I have CISCO 1841 Router connected to the internet and CISCO SGE2000-G5 24ports layer 3 switch that is connected to cisco 1841 router.i want to create vlan in layer 3 switch. [code] i want all vlans would still ping to each other and file/printer sharing is available.kindly check if my network upgrade plan is correct, how am i going to configure those vlan in my layer 3 switch and to connect to the internet.
View 12 Replies View RelatedWe have a couple of cisco SGE switches connected to a single DELL, between the cisco switches we have a trunk interface. I'm not sure which setting should be configured on the switches to get it working because a loop is occuring.
View 1 Replies View RelatedI have recently aquired a Cisco SGE2000 switch and the first thing I did was update to the latest firmware and change password. Now I cant login? Neither my admin / admin dosent work nor the new user I have created. Is there any characters that this dosesnt support like backslashes or forward slashes for password? If not then what can I do to get access to the switch again?
View 2 Replies View RelatedI have a problem for config switch sge2000. I can not console mode to get the prompt to type commands
View 1 Replies View RelatedI am running the SGE2000 as my l3 core switch with multiple inter-vlans.
have a customer requirement that needs to restrict eg. GUEST-VLAN10 to all other VLANS in the network. Only allowing access to the internet.
It seems on the switch i am able to bind ACL to per port interface. if this is possible on the SGE2000
DHCP Relay on a SGE2000 switch.I have configured two VLANs on the switch, VLAN2 (192.168.10.x/24) and VLAN3 (192.168.9.x/24). I have the switch in Layer 3 mode. I have configured the DHCP relay server of 192.168.10.4 and the DHCP Interfaces as VLAN3. All of the IP Static Routes were generated by the switch.
If I put a client computer on a port that is Untagged VLAN 3 and try to get a DHCP address from the server on an Untagged VLAN 2 port I never get a response back.I have done some packet captures and here is what I have found:
I see the DHCP broadcast on the client computerI see the DHCP Request on the DHCP server coming from the IP assiged to the switch on VLAN 3 (192.168.9.254)I see the DHCP server respond with a DHCP OfferThe DHCP offer never gets to the client computer I can't seem to get a DHCP address to any system not on the same VLAN as the DHCP server. Option 82 is disable and I did try enabling it, which made no difference.
I currently am using the SGE2000 switches for our datacentre and they have run great. We are looking at replacing them as part of our normal equipment refresh and have questions about what is the best switch for us. We are looking at upgrading to at least 48 port switches which isn't a huge issue.The main purposes of the switches will be for iSCSI traffic between Starwind SANs and Vsphere 5.1 hosts. We had some latency issues with one of the SGE2000s but otherwise they've been great.
We also will use these switches to handle our feeds from our ISP and our normal interserver communications. We have had DDoS attacks in the past of 40k packets per second and 600mbps and the SGE2000 never even flinched. We don't need it for any layer3 routing (which we use virtualized PFsense for). Looking at the Miercom report the SG200 series looks like it would be fine for us but I'm just worried around the part which mentions it becoame unresponsive in a DoS attack and also whther it may be slower for iSCSI. Both series seem to support flow control and jumbo frames.
We have a standalone Cisco SGE 2000.
We lost connectivity to the web user interface - it no longer responds on the configured IP address.From the manual we see that by default the switch get its IP address via DHCP - but we find no record of any ip address assigned to this switch.Is there a IP address that this unit defaults to when DHCP is not available? Also - what is the best way to connect to the console using Windows 7?
I need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies View Relatedi have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View Relatedwhat is the use of no switch port command in L3 switch?
View 7 Replies View RelatedI have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedI have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedThe last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedI am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
Two Cisco C2960G Switches connected with each other using an EtherChannel Trunk Ports.IOS Image has been upgraded to c2960-lanbasek9-mz. 122- 58.SE2.bin.The global command "sdm prefer lanbase-routing" has been executed to set the default template to "lanbase-routing".The global command "ip routing" has been executed to enable the ip routing.An IP route has been configured in each switch to point to each other for the static routing purpose (Please see the 2 attached configuration files) The hosts in VLAN 111 and VLAN 110 are not able to see each other even the ip static routes have been configured.May be I have misconfigured some settings but not sure what's the actual problem.
View 11 Replies View Relatedmy company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies View RelatedYou can set the ME3400 switch set to the Routing SDM template such that it support PBR. That is done in the ASICs, right? Because if it is done in software the switch could quickly become overwhelmed.
View 2 Replies View RelatedI have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies View RelatedI'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
I have enabled ip routing But I dont have a default route, this is becase we don't have a router on the network.
I am looking for a PoE switch with Routing capabilities (e.g osfp) something lower end than 3560E.
View 10 Replies View Related