Cisco :: 2960 / Login To Switch Via Ssh?
Aug 25, 2011
i have 2960 Catalyst with LANLITE. And i cannot set "transport input ssh", it allows only telnet. I'm wondering if cisco lanlite switches have ssh input in newer releases of IOS or there is no way to make ssh input on this switch?Here's show ver output (i removed all serial and part numbers):
S14#sh ver
Cisco IOS Software, C2960 Software (C2960-LANLITE-M), Version 12.2(37)EY, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Thu 28-Jun-07 18:07 by antonino
Image text-base: 0x00003000, data-base: 0x00D00000
[code]....
View 2 Replies
ADVERTISEMENT
Feb 10, 2013
I have a very problematic situation here.I have configure on a Cisco 2960 the vty line in a wrong manner and now I am stock.To configure those vty to enable ssh I have typed :
line vty 0 4
login local
password xxxx
line vty 5 15
login local
password xxxx
exit
Problem, I work remotely (I was on telnet while doing this). I have no username configure as I thought that root user would work.Now when I issue an ssh to my switch, I always failed authentication.how I could recover access to my switch without being physically there ? I have write the config in memory, otherwise it would have been too easy.
View 5 Replies
View Related
Jan 6, 2012
we have a cisco 2960 48 port tcl switch port and i've enable ssh on my switch and now :
1) how can i login to ssh ? how should create username for ssh ?
2) how can i disable telnet ?
3) how can i change main (master) password?
View 7 Replies
View Related
Dec 30, 2012
I configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
View 4 Replies
View Related
Jun 7, 2011
lets you catalyst 3560 & 2960 remote login with a secure protocol
View 4 Replies
View Related
Oct 23, 2012
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
View 4 Replies
View Related
Dec 3, 2011
if we are unable to login into switch how can we identify at which port of switch loop is there ?
View 3 Replies
View Related
Jul 4, 2011
We are unable to login at Cisco 6509 switch, due to username and password not working. We have tried to recover the password as per Cisco document, but that is also not working. This switch is our Primary Switch in our network.
View 8 Replies
View Related
Apr 8, 2012
SGE2010P won't Switch respond to login after reboot
View 1 Replies
View Related
Jul 5, 2012
I'm unable to login Switch.......getting following error...I have tried this commands on other 3560 that worked...when I enter user name & password re logging authentication failed error occurs .........This is remote site Switch.
[code]...
View 7 Replies
View Related
Dec 29, 2011
I was logged in to this device in monday normally and in tuesday when i trying to
Cisco SW#telnet 172.17.1.1
Trying 172.17.1.1 ...
% Connection refused by remote hos
And i compare the current configuration with last configuration in monday i found no change, this device in live network also cpu is normally and memory.
View 2 Replies
View Related
Mar 29, 2011
I would like to make a centralized management of loggin account on my cisco switch (with a radius server). But, on Cisco 3750 E, i use 12.2(44) SE1 IOS and no command aaa authentication login exist.
Cisco 3750 can support other IOS than 12.2 who have this ability ?
View 2 Replies
View Related
Sep 25, 2012
I have a 3560-X switch and want to access it through GUI. what image I need to download and steps to use GUI(Just like ASDM for ASA 5500 series Firewall).
View 1 Replies
View Related
Aug 13, 2012
'm able to setup my 3750e switch to login through a radius server with my company user id and password but would like to be able to set it up that when I log in it drops me on the enable prompt. Right now I have to type >en.Then the enable password.
View 1 Replies
View Related
Apr 12, 2005
Is it possible to enable login by http (web interface) to catalyst 4006 switch with WS-C4006 Software, Version NmpSW: 6.3(5) ?
View 21 Replies
View Related
Nov 3, 2011
In my lab, there are some machines that are connected using Cisco 2950 switches. Those machines belong to a VLAN.Now I need to modify the VLAN settings of the machines and as such I also need to modify the VLAN settings on the ports on the Cisco switches.
In order to do this, first I need to login to those switches, but due to a lack of knowledge transfer, I don't have the password. Is the some generic password?Second I will need to modify the VLAN settings on each individual port. How can I do this?
View 2 Replies
View Related
Nov 12, 2012
i would like to know how to set the following on cisco ws-c2960-24 ttl:
1. SSH CLI
2.PORT SECURITY REMOVAL: Limits MAC@per port with no shutdown
3.Set port to protect
4.Set RSTP
5. Finally how do i set up TFTP Server from windows server 2008
View 5 Replies
View Related
Dec 15, 2011
I have a cisco catalyst 2060 poe switch, exitsting flas is flash:/c2960-lanbasek9-mz.122-50.SE5/c2960-lanbasek9-mz.122-50.SE5.bin
I downloaded latest flash (c2960-lanbasek9-mz.150-1.SE.bin) and updated the new flas through telnet while reunning tftp server. and tftp server is given the message sent 2960-lanbsek9-mz,SE.bin to (10.10.10.1), 11847957 bytes
after reload the system i login telnet and saw the verson still it is showing old verson, then how can i comform flash is up-dated or not...
DETAILS
my tftp server ip is: 10.10.10.10
switch ip is: 10.10.10.1
View 8 Replies
View Related
Nov 23, 2011
i have a switch 2960 24TC-L with c2960-lanbasek9-mz.150-1.SE.bin and SSH v1 enabled.When i try to enable SSH v2 the swith tell me that i have to create a crypto key rsa. I generated the crypto key rsa with 1024 bits and when i try to enable the SSH v2 i receive the same message.
View 10 Replies
View Related
May 16, 2012
how to shutdown the cisco switch 2960.......
View 5 Replies
View Related
Jan 18, 2012
how to set up SNMPv3 on a Cisco Catalyst 2960-S switch in order to manage it with Cisco Prime NCS?
View 1 Replies
View Related
May 26, 2011
I have a question you do do remote access ssh and telnet remotly to a 2960 switch?
View 6 Replies
View Related
Jan 10, 2012
I replaced an access switch 3750 with a switch 2960. Basically I just copy the whole config of the 3750 to 2960.
The 3750 use AAA, Crypto pki trustpoint TP-self-signed and radius-server host etc.
Now I can only telnet to 2960 but not SSH to it.
View 3 Replies
View Related
Oct 18, 2012
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies
View Related
Nov 8, 2011
We have one Cisco 2960 Catalyst switch.Rule Title: The administrator will ensure passwords are not viewable when displaying the configuration. Right now my user passwords are visible in plaintext. I tried #username <admin> password 7 - but everything I try there is an error I also tried #username <admin> secret but it says I can't have both a secret and password for a single account.
View 1 Replies
View Related
Apr 7, 2012
we are using 2960 cisco switch asn we are trying to configure port security.we are able to configure MAC base port security, but unbale to configure IP base port security.can any one guide us can do IP base port security like MAC port security. if not which switch will support IP and Mac base port security.
View 6 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
May 23, 2011
I have 1 internet router 2960 and 2 No's ASA firewalls,The issue is Suppose if ASA-1 fails the failover will happen on ASA-2 but The issue is i dont have a layer 2 Switch in between the ASA's and Internet router, i have to manually shift the cable from ASA-1 to ASA-2,what sort of configuration i can do on 2960 router interfaces to support failover from ASA-1 to ASA-2, I have enough interface on 2960 router to occupy ASA-2. These all 3 devices should be in 1 Subnet.
View 11 Replies
View Related
Feb 5, 2013
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
View 5 Replies
View Related
Dec 12, 2006
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies
View Related
Jan 14, 2013
I am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies
View Related
Aug 20, 2012
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
View 3 Replies
View Related
Apr 29, 2012
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
View 5 Replies
View Related
