I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 RepliesI want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
View 1 Replies View RelatedIn an attempt to restore a Cisco IOS I deleted the file C2960-lanbasek9-mz.122-53.SE2.bin my swich
Before deleting the same was as follows:Directory of flash :/
3-rwx 12824 Mar 28 1993 21:00:37 -03:00 vlan.dat4-rwx 3096 Mar 7 2012 08:43:37 -02:00 multiple-fs5-rwx 2289 Mar 7 2012 08:43:37 -02:00 private-config.text6-rwx 7482 Mar 7 2012 08:43:37 -02:00 config.text9 drwx 192 Mar 23 2012 16:18:54 -03:00 C2960-lanbasek9-mz.122-53.SE2
32514048 bytes total (20204544 bytes free)Switch-01 #
Right now this switch as follows:
switch: dir flash:Directory of flash:/
2 drwx 64 <date> crashinfo_ext 3 -rwx 4120 <date> multiple-fs 5 -rwx 12824 <date> vlan.dat 6 -rwx 4018 <date>
[Code].....
I have a Cisco Catalyst 2960 series switch. When I connect another switch or a VMWare Esx server on one of the ports, the port blinks for few seconds and then goes off. When I connect a desktop or laptop or a windows server the ports stay led and I can access resources on the network. However, when connect another switch or a vmware esx server, the port is disabled.
What config in the switch can I check to make sure the ports stay on regardless when I connect a desktop / laptop, switch or vmware server?
Cisco Catalyst 2960 series,i want do a SNMP request over OID. When the output should be like this: Portnumber and VlanID. Is there a OID for this output?
View 1 Replies View RelatedI'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
Im trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
I have a device that does ip audio on one mac address and managagement is on another mac address. Both of these mac addresses come from one NIC on the device. We need to split these two traffic paths into two different vlans.How can I program this switch to sperate the different traffic into two vlan's based on mac address on one interface?
View 2 Replies View RelatedI have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
When i connect two cisco 2960 series switchs via stright trough cable causes delay in transmission sw1 has vlans and having trunk port connected to router all vlans are able to access internet sw2 is connected to vlan5 on switch1 sw2 has factory default configuration computers on sw2 can access internet but I have low bandwith problem on sw2 there is transmission delay problem?
View 1 Replies View RelatedHow to change ip address in cisco 2960 series switch?
View 4 Replies View RelatedSuddenly my 2960 D series switch went offline and i founf the switch was not powering. I can't figure out the issue.
View 3 Replies View RelatedI added Linksys RV-016 16-ports VPN Router into the connection. RV-016 supported multiple subnets.
As mentioned in [URL], D-Link DIR-615 needs to be a device which could support multiple Vlan subnets. But unluckily DIR-615 does not support multiple Vlan subnets.
Therefore I added Linksys RV-016 in the the combination of devices. As what i found in RV-016 GUI setting, it supports multiple subnets.
Purpose outline:
1. Have to create two different SSIDs.
- SSID 1 for Management (able to view all other LAN devices)
- SSID 2 for guest and staff (unable to view all other LAN devices)
2. Create two VLANs in catalyst 2960s.
3. Create two subnets in Linksys RV-016 to accept two Vlans from catalyst 2960s.
Any experience of configuring RV-016 for the mentioned purpose above?
how to safely remove the WiSM2 from the Catalyst 6500 series switch? According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":
To remove the WiSM2, perform these steps:
Step1 Shut down the module by one of these methods: In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module: Router# no power enable module modRouter# power enable module mod If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Step2 Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.
But, in the case of Step1 (1st methods) I do not see a option "shutdown" in the command "hw-mod module 3"...
All I prompted to enter is: c6500#hw-module module 3 ?
boot Specify boot options for the module through Power Management Bus control register
reset Reset specified component
simulate Simulate options for the module Is it hidden options?
IOS version of c6500 is 12.2(33)SXJ1
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?
I am trying to get the temperature reading from one of our 3560G Switches using SNMP. When I run an snmpget on the Switch it returns back to me a "1".
So when I run the following I get:
> snmpget -v1 -c public 192.168.x.xxx 1.3.6.1.4.1.9.9.13.1.3.1.3.1005
SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.1005 = Gauge32: 1
But when I telnet to the device and run a "show env temperature status" I get:
# show env temp status
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 51 Degree Celsius
Red Threshold : 61 Degree Celsius
So I'm not sure why I am getting a "1" when using snmpget on the OID 1.3.6.1.4.1.9.9.13.1.3.1.3.1005 which is (ciscoEnvMonTemperatureStatusValue)??
If I run the same OID on another 3560G Router I get the correct output from snmp....
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
In a switch catalyst 2960 the IOS is erasing in flash, for the transfer IOs respalding to flash no function the current command. how is the method.
View 6 Replies View RelatedI want to configure my switch via console cable, the switch boots up normally, and there are no configurations present on the switch. However, anything I type does not appear on the terminal client. I used several terminal clients (TeraTerm, PuTTY, HyperTerminal), all latest versions as well as different PCs. I even forced the switch to rommon mode, still, anything I type does not appear on the terminal client.
Here's the output of TeraTerm:
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: e8:40:40:06:f0:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
[code]....
After the last line, I can not type any command at all. I encountered this on three 2960 switches that we have here in our laboratory.
I need to connect these devices:
- Some computers.
- A Cisco Catalyst 2960 switch (computers must be connected to this switch)
- A ADSL router Zyxel P-660HN-T1A with WiFi (the switch must be connected to this router)
In my company we have at least 10 computers which were connected to Internet using a WiFi connection. But now we need these computers connected to a wired line and this router has just 4 Ethernet ports which are not enough obviously. So we bought this 24-port Cisco switch to connect all the computers and I don't know how to connect it to the ADSL router and what configurations to set up in order to have access to internet in every computer connected to the switch.
How can i Upgrade Catalyst 2960 switch software in Rommon mode (switch:)
Right now flash is empty.
I want to limit the bandwidth of my Catalyst 3750 series switch, I read the cisco documentation and I applied the commands but I didn't get the wanted results.
For the outbound traffic it's ok, but for the inbound traffic I used policing but I get an unstable traffic. I used, an access list and a class-map to classify the traffic and then a policy-map.(I followed the steps mentioned in this site: [URL]
I Have a problem I'm trying to configure automatically my switch over ther DHCP when I start the switch it request an IP from the DHCP from here everythings is fine but it does nothing more,indeed I put on my dhcp the option 66 and 67 which is an adress of my TFTP server and a file to download and the switch seems not to understand theses options , I tried my dhcp with a cisco airport and everythings works fine the File from the TFTP is automatically downloaded into the airport...There is an option to add or am I missing something in order to make it work with my switch ?
My switch : Catalyst 2960IOS VER : 12.2(55)SE5
I planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
I want to configure IEEE 802.1x port-based authentication on cisco switches, preferable 2960 series. Which models support this feature?. I have try with some older switches but it doesn't works properly on everyone. I have upgraded them whitout better results, there is namely an issue with TLS handshaking on some switches which produces authentication to fail.
View 1 Replies View RelatedWondering if this switch is capable of being a backbone switch for a network of about 1000+ users and if the switch can handle a sustained 30Meg of data going across it?
View 3 Replies View RelatedCan we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View Relatedwe are using 2960 cisco switch asn we are trying to configure port security.we are able to configure MAC base port security, but unbale to configure IP base port security.can any one guide us can do IP base port security like MAC port security. if not which switch will support IP and Mac base port security.
View 6 Replies View RelatedIf I knew the IP address of a host, can we know on which port on the switch its connected. The switch model is 2960
View 6 Replies View RelatedAs per my attached diagram, I have three switches (Cat 3560-E and couple of Cat 2960-G)
Each PC is on different vlan
PC -1 on vlan 100
PC-2 on vlan 200
I need to connect PC-1 and PC-2 to the server. Server has no fixed vlan and can be changed.
Restrictions:
1) can’t change PCs vlan assignment.
2) can’t add 2nd NIC in the server.
I’ve tried private vlan but it requires separate physical ports for host and/or community vlan and somehow it did not work. I could be wrong Trunking using dot1q enabled on port 2 on all switches and connection works fine (server to PC-1 or server to PC-2) by enabling switchport access vlan 100 or switchport access vlan 200. However I need port 5 on switch-1 to respond to vlan 100 and 200.
we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View Related