Thinking of getting one of those 8-port 2960 for a CCNP study. Is the difference between the C2960-8TC-S and the C2960-8TC-L models in Hardware, or in IOS? or both? And if it's in IOS, is the S upgradable to L?
View 7 RepliesWe ordered 4x cisco 2960 switch with LAN Lite software by mistake. Can we upgrade them to Lan Base?When I change boot image I get Error: hardware not supported by firmware.
View 3 Replies View Related1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
How do I tell if my cisco 2960 has the Lan Base or Lan Lite image?
View 11 Replies View RelatedWhat is the difference between IP Base and Universal for 3750X switches?
View 2 Replies View Relatedcan we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies View RelatedA quick one because I'm scratching my head trying to figure the difference between the 2960 LAN Base and LAN Lite IOS installs. I want to put a 2960 into a site which has as layer 2 link on dark fiber taking it elsewhere. This part I'm not concerned about - the WS-C2960--24TC will do what I need without issue - but I don't know if I can get away with LAN Lite, or if I need LAN Base.
I basically need V LAN's with associated SVI's, and a routed link on the up link port (I don't care if it's a switch port with an associated SVI or a no switch port and IP address), but it's got to be able to run OSPF. Can I do this with LAN base on this series switch? Or do I need to go for a higher series (3560?). I *could* get away with static routes, but my boss is walking death on them unless I can 100% prove they're necessary, so I'd rather not right that fight!
we have inserted into a network with VTP a Cisco Switch 2960-S, not knowing that had installed IOS LAN lite.Now I discovered that it can handle up to 64 vlan. In the network there are currently configured 62 VLAN: what happens when we exceeded the max number (64) of VLAN for that switch?
View 6 Replies View RelatedI need to buy a cheap Cisco switch with DHCP server.Can you confirm that 2960-24-S, 2960-24TC-S and 2960-48TC-S be a DHCP server?
View 3 Replies View Relatedwhat iz the difference between 10Base-T and 10 Base-Tx?
View 1 Replies View RelatedI have some 2960 switches with Lan Lite ios in my infrastructure.And I try to configure them to support "trust device cisco-phone" and "switchport priority extend cos 0" on ports with cisco phones.But LAN Lite image does not support "mls qos trust device cisco-phone".can I use any workaround to trust cos of cisco phone and to remark PC traffic with cos 0?
View 1 Replies View RelatedAny document to explain the differences in the Software images for the ASR1001 routers.
View 3 Replies View RelatedI have a 2960 SI lan lite switch that I am configuring for admin and guest access. I have wireless AP's plugged into trunked ports 2 and 3. I am using two vlan's (in addition to the native VLAN). Vlan 5 for Admin and Vlan 10 for guest access. I have ACL configured on the router preventing guest users from accessing the Admin network. I want to prevent those on the guest network from seeing other hosts in the vlan however the lan lite software does not support port ACL's. Any way to accomplish this with this switch.
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code]...
Any major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
I plugged an IP device into a 2960 Catalyst switch. The port is up, but there is no MAC address learned on it:
TNSWAGCS01002(config-if)#do sh mac add int fa0/16
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
TNSWAGCS01002(config-if)#
TNSWAGCS01002(config-if)#do sh int fa0/16
FastEthernet0/16 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0064.40ee.f510 (bia 0064.40ee.f510)
Description: --- STC ---
[code]....
I read that it may be a L1/L2 issue. We tried with another ethernet cable. We also tried with another IP device of the same model. That did not solve the issue.
I am trying to test (if possible) the idea of having 2 6509-E switches connected directly to each other while using VRF-lite (Sup 2T). The idea is to have 3-4 separate networks. For example Net-A, Net-B,Net-C, Net-D. There is no PE router*, just these two switches. Also, there sin't any other access layer switches. All users connect directly to the 6509-E's via switch 48 port switch blades.
Net-A and Net-B on separate VRF's, but able to talk to each other. Net-C and Net-D* on separate VRF's without being able to talk to any other. Net-D* will have a PE since it comes from an external network. This is something I would like to test in a lab environment, but I am not familiar with VRF's.
I'd like to know if is it possible to load lan base image on Cisco Switch 2960 TC-S. This model (WS-C2960-48TC-S) come with lan lite image and it's the same (phisically) of the 2960 TC-L (lan base image).If I try to upload the lan base image on flash of 2960 TC-S will works?? ..or the switch goes damaged?
View 2 Replies View RelatedWe're replacing our older catalyst switches with new SG300 family switches and have a Microsoft NLB cluster for some services that run in multicast balancer mode.
We currently do L3 routing to the network with the cluster and have the following IOS configuration line in the specific switch to let users on other subnets to access the services.
arp 10.20.1.226 03bf.0a14.01e2 ARPA
How do we replicate this using the SG300 series in L3 mode? Whenever I try to add a manual ARP entry I get an error message that says that the MAC address is not a valid unicast address?
I'm setting up two vlans and I would like all of vlan 2 to only have access to the WAN router on vlan1 at 192.168.30.1.
VLAN1 192.168.30.x
VLAN2 192.168.31.x
I've setup the VLANS and static routes and I'm able to access the WAN router at 192.168.30.1 from the 192.168.31.x network and everything is fine.
I'm getting an error setting up the IPv4 based ACL that is designed to allow the 192.168.31.x network access to only the 192.168.30.1 WAN router.
The first rule I setup is to permit source 192.168.31.0 / 0.0.0.255 dest 192.168.30.0/0.0.0.255 to allow all traffic to from the 192.168.31. net to access the 192.168.30.x net. Then I was going to deny the dest of 192.168.30.1-255 but I'm not sure of the wildcard to use for that.
I'm not clear on the wildcards but I'm also getting the following error when I setup the first ACE rule:
"MIB Index is out of range.Index must be bigger then 0 and Existing ifindex.."
I suspect the error is related to how I'm using the wildcards?
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedI am getting very frustrated trying to modify/create ACL's on my SG300-20 switch.I have the switch in L3 mode. I have created several VLAN's and ACL's for each VLAN controlling their access to each other. After the initial setup, I have started trying to create more VLAN ACL rules to allow more access between the VLAN's. The problem I keep running in to is that when I go to modify the ACE's in the ACL, I keep getting the error message "Entry already exists". For example, I go to modify the port ranges to tighten them up, and try to save the ACE after modifying it, and I get that error message.
View 7 Replies View RelatedWhat is the difference between sdm prefer access & sdm prefer default & sdm prefer lanbase-routing? When do we use these options?
View 2 Replies View RelatedI have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies View RelatedI'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 5 Replies View RelatedI'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 1 Replies View RelatedWe are using 18 numbers of 3560X -Lan base series switches in our network(Access layer). We have 400 users and created vlans in access switches. we are planning to purchase Two numbers of 4900 M as Core layer switch and for redundancy. The uplink would be on 10 gig copper cable (CAT 7) between the access layer switches and core switches. I like to know whether 4900M can take the load of 18 access switches.
View 1 Replies View RelatedI have a 2960S switch and nine (9) 300 switches. I have three VLANs configured on them, data, voice and management. Each 300 has unique data and ovice VLANs corresponding to their locations. All of the 300 switches connect to the 2960 in a hub and spoke network topology via 802.1q trunks. I can access devices between switches on the data and voice VLANs fine from any other switch. My issue is that from any 300 switch I can access the 2960 management VLAN interface without a problem, but I can not access the 300 switch management VLAN that I am connected to from the CLI. I do not use the GUI at all for management.
View 22 Replies View RelatedI need to retrieve my password for the linksys router wrt54g
View 1 Replies View RelatedWhat is the difference between the 2950 and 2950c switches? I tried finding it on the feature navigator but I couldn't. And I wasn't able to get anything from the Cisco website either. (I didn't really look through the long PDFs, I'm sure there is a more simple way to find the answer to this that I'm not aware of.)
View 3 Replies View RelatedI wonder what is the difference between SF200 and SF200E smart switch. They seem like having same spec.
View 2 Replies View RelatedWhat is the difference between a SGE2000 and a SG500-28?
View 3 Replies View RelatedI need to ask if what is the main difference between an SD208T and SF90D. Aside from the price in which SF90D cost lower than that of the SD208T and that SF90D has replaced the SD208T, what else does these two differs?
View 2 Replies View RelatedDifference between wireless routers.
g
n
d
what is the difference between these router and which is best? i have the linksys wireless g 54 mbs.