We ordered 4x cisco 2960 switch with LAN Lite software by mistake. Can we upgrade them to Lan Base?When I change boot image I get Error: hardware not supported by firmware.
View 3 Replies1)For 3650X I found some contradiction in the Q&A about feature set LAN Base vs IP Base:
LAN Base: Can I do static IP routing ?
LAN Base: SVI => is this for intervlan routing ?
2)For 2960, there are 2 flavors (LAN lite and LAN BASE) Q: Can I do static routing on one of these flavors ?
Thinking of getting one of those 8-port 2960 for a CCNP study. Is the difference between the C2960-8TC-S and the C2960-8TC-L models in Hardware, or in IOS? or both? And if it's in IOS, is the S upgradable to L?
View 7 Replies View RelatedHow do I tell if my cisco 2960 has the Lan Base or Lan Lite image?
View 11 Replies View RelatedA quick one because I'm scratching my head trying to figure the difference between the 2960 LAN Base and LAN Lite IOS installs. I want to put a 2960 into a site which has as layer 2 link on dark fiber taking it elsewhere. This part I'm not concerned about - the WS-C2960--24TC will do what I need without issue - but I don't know if I can get away with LAN Lite, or if I need LAN Base.
I basically need V LAN's with associated SVI's, and a routed link on the up link port (I don't care if it's a switch port with an associated SVI or a no switch port and IP address), but it's got to be able to run OSPF. Can I do this with LAN base on this series switch? Or do I need to go for a higher series (3560?). I *could* get away with static routes, but my boss is walking death on them unless I can 100% prove they're necessary, so I'd rather not right that fight!
can we upgrade 2960 switch from Lanbase IOS to IPbase
View 4 Replies View Relatedwe have inserted into a network with VTP a Cisco Switch 2960-S, not knowing that had installed IOS LAN lite.Now I discovered that it can handle up to 64 vlan. In the network there are currently configured 62 VLAN: what happens when we exceeded the max number (64) of VLAN for that switch?
View 6 Replies View RelatedI need to buy a cheap Cisco switch with DHCP server.Can you confirm that 2960-24-S, 2960-24TC-S and 2960-48TC-S be a DHCP server?
View 3 Replies View RelatedI have some 2960 switches with Lan Lite ios in my infrastructure.And I try to configure them to support "trust device cisco-phone" and "switchport priority extend cos 0" on ports with cisco phones.But LAN Lite image does not support "mls qos trust device cisco-phone".can I use any workaround to trust cos of cisco phone and to remark PC traffic with cos 0?
View 1 Replies View RelatedI have a 2960 SI lan lite switch that I am configuring for admin and guest access. I have wireless AP's plugged into trunked ports 2 and 3. I am using two vlan's (in addition to the native VLAN). Vlan 5 for Admin and Vlan 10 for guest access. I have ACL configured on the router preventing guest users from accessing the Admin network. I want to prevent those on the guest network from seeing other hosts in the vlan however the lan lite software does not support port ACL's. Any way to accomplish this with this switch.
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code]...
I'd like to know if is it possible to load lan base image on Cisco Switch 2960 TC-S. This model (WS-C2960-48TC-S) come with lan lite image and it's the same (phisically) of the 2960 TC-L (lan base image).If I try to upload the lan base image on flash of 2960 TC-S will works?? ..or the switch goes damaged?
View 2 Replies View RelatedI have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedWhat is the difference between IP Base and Universal for 3750X switches?
View 2 Replies View RelatedI'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 5 Replies View RelatedI'm building a wired closet to aggregate user's connections, Im planning to have 5x 3750X stacked switches and there is a need to run EIGRP, I'm thinking to order one switch with IP service image while the rest will run IP base image, is it workable scenario and what are the drawbacks of such combination of images ?
View 1 Replies View RelatedWe are using 18 numbers of 3560X -Lan base series switches in our network(Access layer). We have 400 users and created vlans in access switches. we are planning to purchase Two numbers of 4900 M as Core layer switch and for redundancy. The uplink would be on 10 gig copper cable (CAT 7) between the access layer switches and core switches. I like to know whether 4900M can take the load of 18 access switches.
View 1 Replies View RelatedI have a WS-C3750X-12S-S (IP Services) that I THINK I'd like to downgrade to LAN Base so I can stack it with a WS-C3750X-48T-L that is already LAN Base..
View 4 Replies View RelatedI am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View RelatedWe have 3 layer LAN architecture, layer 1 of 6500(IP routing), layer 2 of 4500(L2 switch only), layer 3 of 2960(L2 Switch)In a Single (2960 and 4500) Switch Port Avaya IP phone and PC are connected.Now, the requirement is that, Qos need to be configured for Voice traffic and Data traffic should be in default class of service.We plan to use COS value in Switch 4500 and 2960. We made a sample configuration as below
### For 4500 Switch
class-map match-all VOIP-Access-2MB
match cos 3 5
class-map match-all VOIP-Uplink-20MB
match cos 3 5
[code].....
check these configurations are correct as per standard and if there is any other method of configuration?What need to be configured in L3 Switch(6500)??In 2960, it doesn't support ingress QoS, what impact it will make when compare to 4500? do users experiance any difference?
Are the non-S series 2960 switches stackable or are they only able to be uplinked?
View 6 Replies View RelatedCompany I work for just moved into a new location. We have two data closets which are patched as independent entities, with no Ethernet tie connection. These closets are roughly 100 feet apart.
There is a fiber connection that runs between both closets, that the previous tenant used to connect the switches. I have placed a Cisco 2960 switch in each location, and added one mini SFP gbic's to each switch. After attaching both sides, neither light up. I do a sh inter gig1/0/49 on each and shows 'down down' (not admin down).
What is the trick on getting these to communciate, do I need to configure these ports, and are they supposed to light up?
What I am trying to accomplish is to get the one closet that is completely cut off, communicating by logically stacking, or 'daisy chaining' via fiber.
I turned off the lights and popped the fiber out, and I do see a faint red light (I did not look straight into it), so I think the fiber is active.
I have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?
Is there any tool to perform this task?
I have a number of 2960 switches that have crashed without any reason
Under show version System returned to ROM by address error at PC 0x108971C, address 0x0
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature?
View 1 Replies View RelatedI have a customer with Cisco 7940 and 7960 IP phones that they do not plan to replace. They do want a new LAN and are looking at the Catalyst WS-C2960S-48FPD-L and WS-C2960S-24PD-L as access layer devices.
these switches support the Cisco pre-standard PoE required by the 7940 and 7960 IP phones.
Any one who knows where I can find a documentation where it says the maximum switches per stack for the Catalyst 2960 family?
View 2 Replies View RelatedI need to connect 4 Floor Building with 4 Cisco 2960 - 48 ports switch each other and it needs to be through a fiber. So all PCs connected to each switch would reach the LAN/WAN from the other switch. (attached is the image here with)
I see that the 2960 has 2 SFP ports each port of each switch should connect each other or how?
My simple question is:
1. What cable / patch code I have to use = Single-mode or Multimode? ( distance for each switch will not more then 25 mts)
2. Do I have to use SFP or SFP+ module?
3. What kind of SFP/SFP+ module I have to use = Single-mode or Multimode?
4. What kind of connector should patch code have = LC / SC or ?
5. How to connect each switch with redundancy like ...each switch should be interconnected with each other or I have to choose Cisco 3750G which has more then 2 SFP ports (option#1 & opetion#2 = attached here with) =
Best practice for connecting cisco switches over fiber.
We had core(4503), distribution(3750), and access switches(2960) in our environment. Currently we configured the clock manually in each switch, but a reboot of the switch resets the clock also. We are planning to make a single switch as a NTP servers and others are clients to synchronise the correct time even after a reboot of the access switches.
View 6 Replies View RelatedFor a simple ether channel to work between 2 switches I have configured ports 1 and 2 on both cisco 2960 switches with the channel-group option like this:
interface FastEthernet0/1
channel-group 1 mode on
!
interface FastEthernet0/2
channel-group 1 mode on
I thought the port-channel 1 would get automatically created but it didn't, should it? And under the port-channel interface should I set this as a trunk or do I do this on the 2 fa interfaces on each switch?
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
I have a design for my infrastructure and i'm thinking to choose 4 or 5, or more, 2960 series in a stack mode instead of one 4500 series?
View 6 Replies View RelatedI configured port security on my 2960 switches with the following commands: [code]
The problem is that when I should change someone's PC, first I disable port-secirity, then I clear all the mac addresses learned on the interface, then I plug the new PC and enable port-security. The new PC couldn't connect to the network and it's mac address has not be learned on the interface. Why?Which commands should I use to clear an old mac address and enable port-security with the new mac address.
I am trying to get to work Web-based authentication on Catalyst 2960 and 3560 for clients that don't support dot1x. I followed this guide. Here's the problem: Client (win7) joins the network, opens the web browser and tries to navigate to any http site. The switch forces him the "login" page in which he has to enter credentials. After the client enters credentials, the switch sends http 500 internal server error page and nothing happens. Doesn't matter if the credentials were correct or not. Also i checked radius logs for requests, the switch doesn't even ask radius.
The configuration:
sh ip admission configuration
Authentication Proxy Banner not configured
Consent Banner is not configured
[Code].....