I have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?
Is there any tool to perform this task?
how can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies View RelatedIt seems my 2960s and 3560s switches have enough flash space and memory to support the 15.0 IOS should I be OK to jump to this from 12.2(35)?
View 10 Replies View RelatedI am trying to copy IOS from my TFTP server which is on my laptop to cisco 2960 switch
I am able to ping to switch from my laptop, connectivity is fine, tftp server is running
Current Image on Switch --> C2960-LANBASE-MZ.122-25.SEE3.bin --> trying to upgrade to --> c2960-lanbasek9-mz.122-53.SE2
I am getting below error when trying to upgarde IOS:
2960-SW#copy tftp: flash:
Address or name of remote host []? 10.1.x.x
Source filename []? c2960-lanbasek9-mz.122-53.SE2
[Code].....
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedThe company I work have finally decided to enter the 21st century and invest in a new telephone system (Interactive Intelligence) to replace the legacy system which has served us well for the past 10 years. The project has only just started and involves upgrading sections of CAT3 cabling to CAT6, replacing Cisco 3550 switches in one area of the building with Cisco 4507 switches and upgrading our Core switches with Cisco Nexus 7010's. The area that concerns me most is enabling the network for qos as I have very little experience with it. At the moment Im trying to read as much documentation as I can on QOS to bring myself up to speed.
The access layer switches will consist of a mixture of Cisco 3750 & 4507 switches connected to Cisco Nexus 7010 switches which will form a collapsed aggregation & core layer.
Basically, how I should approach this daunting task of making sure the network will support VOIP.
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View RelatedWe have 3 layer LAN architecture, layer 1 of 6500(IP routing), layer 2 of 4500(L2 switch only), layer 3 of 2960(L2 Switch)In a Single (2960 and 4500) Switch Port Avaya IP phone and PC are connected.Now, the requirement is that, Qos need to be configured for Voice traffic and Data traffic should be in default class of service.We plan to use COS value in Switch 4500 and 2960. We made a sample configuration as below
### For 4500 Switch
class-map match-all VOIP-Access-2MB
match cos 3 5
class-map match-all VOIP-Uplink-20MB
match cos 3 5
[code].....
check these configurations are correct as per standard and if there is any other method of configuration?What need to be configured in L3 Switch(6500)??In 2960, it doesn't support ingress QoS, what impact it will make when compare to 4500? do users experiance any difference?
Are the non-S series 2960 switches stackable or are they only able to be uplinked?
View 6 Replies View RelatedCisco 4506-E port configuration
WESTERN-4506-01#show int g4/47
GigabitEthernet4/47 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 0022.554c.01fe (
fe)
Description: Trunk to 425
[code]....
Cisco 3750 Configuration
interface FastEthernet1/0/1description 425Linkswitchport trunk encapsulation dot1qswitchport trunk native vlan 30switchport trunk allowed vlan 30,35switchport mode trunkswitchport nonegotiateswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitystorm-control broadcast level pps 300storm-control multicast level pps 300storm-control action trapmacro description cisco-desktopmac access-group AuthorizedHosts in
I have mac address' populated. I can see the device in layout on CNA with the proper name however cannot ping it.
4506 is 10.30.30.1
3750 is 10.30.30.2
Two days back my entire network was behaving in unusual ways.When is connect to core switc(4506e) through console. [code]
View 11 Replies View RelatedCompany I work for just moved into a new location. We have two data closets which are patched as independent entities, with no Ethernet tie connection. These closets are roughly 100 feet apart.
There is a fiber connection that runs between both closets, that the previous tenant used to connect the switches. I have placed a Cisco 2960 switch in each location, and added one mini SFP gbic's to each switch. After attaching both sides, neither light up. I do a sh inter gig1/0/49 on each and shows 'down down' (not admin down).
What is the trick on getting these to communciate, do I need to configure these ports, and are they supposed to light up?
What I am trying to accomplish is to get the one closet that is completely cut off, communicating by logically stacking, or 'daisy chaining' via fiber.
I turned off the lights and popped the fiber out, and I do see a faint red light (I did not look straight into it), so I think the fiber is active.
I have a number of 2960 switches that have crashed without any reason
Under show version System returned to ROM by address error at PC 0x108971C, address 0x0
I started having connectivity issues between my core 4506E (Sup7E) and Cisco 2960S. There were input and CRC errors on Te int (SFP 10Gb - LRM) on 2960S, which cause the interface to reset and drop connections. While troubleshooting this issue, I have replaced patch cords and also had the tech checking the fiber. He said that there was some residue on one of the connectors, so the light levels fluctuated in 1300nm, but worked fine in 850. Well LRMs are using 1300, so he re-polished the tips, which worked to stabilize the light levels. After all that, I was still receiving the input/CRC errors, but the connection was NOT dropping. As my last resort I swapped the SFPs between the core and 2960, thinking I should start having issues on the core end. Well, here's what happened: I stopped receiving input/CRC errors on 2960 (also no errors on the core), but 2960s started generating Rx power high alarms: [code]
View 1 Replies View RelatedI would like to check if it may be possible to hot-upgrade/swap the 4506E power supplies? Based on the configuration guide; I have summarized the steps as follows:
1. Switch has 2 existing power supplies to be upgraded
2. Remove right side/bay 2 power supply and install new power supply
3. At this point; the new power supply will be in err-disabled due to different power supplies on the switch
4. Remove the left side power supply and install new power supply
For item 4; during the removal of the old power supply in bay 1/left side and installation of the new power supply; I am wondering if the switch would lose power even though the new power supply is installed in bay 2?
I have two cisco 4506-E series switches ..
We are planning to go for HSRP redundancy for 32 VLANs. Means In a Cisco 4506-E switch , we will configure 32 vlans and among them 16 vlans will be primary and 16VLANs will be standby ans it is viceversa in another core-switch
My querie is How many standby groups can we create in Cisco 4506-E switch,
Is there any limitation..
If there is any limitation , can we go ahead with VRRP,GLBP? Are there any limitation in VRRP/GLBP? Is there any design related issue can we face if we use same group number to all VLANs?
Product details :
Model : Cisco 4506-E
Sup Model : WS-X45-SUP6L-E
IOS : S45EIPBK9-12254SG
I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View RelatedI am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature?
View 1 Replies View RelatedI have a customer with Cisco 7940 and 7960 IP phones that they do not plan to replace. They do want a new LAN and are looking at the Catalyst WS-C2960S-48FPD-L and WS-C2960S-24PD-L as access layer devices.
these switches support the Cisco pre-standard PoE required by the 7940 and 7960 IP phones.
Any one who knows where I can find a documentation where it says the maximum switches per stack for the Catalyst 2960 family?
View 2 Replies View RelatedWe ordered 4x cisco 2960 switch with LAN Lite software by mistake. Can we upgrade them to Lan Base?When I change boot image I get Error: hardware not supported by firmware.
View 3 Replies View RelatedI need to connect 4 Floor Building with 4 Cisco 2960 - 48 ports switch each other and it needs to be through a fiber. So all PCs connected to each switch would reach the LAN/WAN from the other switch. (attached is the image here with)
I see that the 2960 has 2 SFP ports each port of each switch should connect each other or how?
My simple question is:
1. What cable / patch code I have to use = Single-mode or Multimode? ( distance for each switch will not more then 25 mts)
2. Do I have to use SFP or SFP+ module?
3. What kind of SFP/SFP+ module I have to use = Single-mode or Multimode?
4. What kind of connector should patch code have = LC / SC or ?
5. How to connect each switch with redundancy like ...each switch should be interconnected with each other or I have to choose Cisco 3750G which has more then 2 SFP ports (option#1 & opetion#2 = attached here with) =
Best practice for connecting cisco switches over fiber.
We had core(4503), distribution(3750), and access switches(2960) in our environment. Currently we configured the clock manually in each switch, but a reboot of the switch resets the clock also. We are planning to make a single switch as a NTP servers and others are clients to synchronise the correct time even after a reboot of the access switches.
View 6 Replies View RelatedFor a simple ether channel to work between 2 switches I have configured ports 1 and 2 on both cisco 2960 switches with the channel-group option like this:
interface FastEthernet0/1
channel-group 1 mode on
!
interface FastEthernet0/2
channel-group 1 mode on
I thought the port-channel 1 would get automatically created but it didn't, should it? And under the port-channel interface should I set this as a trunk or do I do this on the 2 fa interfaces on each switch?
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
I have a design for my infrastructure and i'm thinking to choose 4 or 5, or more, 2960 series in a stack mode instead of one 4500 series?
View 6 Replies View RelatedI configured port security on my 2960 switches with the following commands: [code]
The problem is that when I should change someone's PC, first I disable port-secirity, then I clear all the mac addresses learned on the interface, then I plug the new PC and enable port-security. The new PC couldn't connect to the network and it's mac address has not be learned on the interface. Why?Which commands should I use to clear an old mac address and enable port-security with the new mac address.
I am trying to get to work Web-based authentication on Catalyst 2960 and 3560 for clients that don't support dot1x. I followed this guide. Here's the problem: Client (win7) joins the network, opens the web browser and tries to navigate to any http site. The switch forces him the "login" page in which he has to enter credentials. After the client enters credentials, the switch sends http 500 internal server error page and nothing happens. Doesn't matter if the credentials were correct or not. Also i checked radius logs for requests, the switch doesn't even ask radius.
The configuration:
sh ip admission configuration
Authentication Proxy Banner not configured
Consent Banner is not configured
[Code].....
What all the catalyst models support VPC with Nexus ? I knew Cat6K and 3750. Any other model supports VPC ? Can I configure vpc between 2960 and N7K ?
View 3 Replies View RelatedI think choose this SWITCH 4506-E and I need running only features L2 Metro, but Idont known what IOS for this!
View 1 Replies View RelatedI have one 4506E switch working in Lan setup as a core switch with WS-X45-SUP6L-E running ipbase IOS 12.2(54)SG1. Each time after reload the switch we found that the clock is getting reset ( time is getting changed ) where as day, date & year is unchanged.
View 2 Replies View Relatedhow can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies View RelatedHow do you enable multicast traffic on 2900 series switches?
View 7 Replies View Related