Cisco Switching/Routing :: 3750 To 4506E Trunk Connection?
Sep 26, 2012
Cisco 4506-E port configuration
WESTERN-4506-01#show int g4/47
GigabitEthernet4/47 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 0022.554c.01fe (
fe)
Description: Trunk to 425
[code]....
Cisco 3750 Configuration
interface FastEthernet1/0/1description 425Linkswitchport trunk encapsulation dot1qswitchport trunk native vlan 30switchport trunk allowed vlan 30,35switchport mode trunkswitchport nonegotiateswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitystorm-control broadcast level pps 300storm-control multicast level pps 300storm-control action trapmacro description cisco-desktopmac access-group AuthorizedHosts in
I have mac address' populated. I can see the device in layout on CNA with the proper name however cannot ping it.
4506 is 10.30.30.1
3750 is 10.30.30.2
View 10 Replies
ADVERTISEMENT
Nov 8, 2011
I have a couple 3750 switches that I am trying to run VTP Version 3 on.one as primary and the other as "server" which implies secondary from my research. [code]Additionally, running a show VTP devices yields a "No VTP3 devices found" on both devices. Despite ensuring that the domainname and password match.I have a patch cable from Gi1/0/1 on switch one runnning to Gi1/0/1 which from what I read is acceptable on GigE.
View 2 Replies
View Related
Jan 29, 2012
I have client who has two distant offices with 3750 L3 as core (do all vlan routing for local office) and multiple L2 access switches with multiple VLAN’s connected to it. First 3750 is hub also connected to internet, second 3750 is spoke and acting as a router on stick. We have eigrp configured on both side ISP provided client 100Mbps link as a trunk with two vlan; vlan10 for voice and vlan20 for data. We assigned two small subnets to these vlans 10.15.17.0/29 and 10.15.17.9/29. Hub addresses are 10.15.17.1 and 10.15.17.9 respectively. How to force voice over VLAN10 and data via vlan20, but still do some load balancing? How to setup default route on second (router on stick) switch?
View 1 Replies
View Related
Nov 8, 2011
Currently we have a 6513 core (running IOS and doing limited routing) with VLAN Trunking to about a dozen 3560 edge switches, with various VLANs going to each of the edge switches. All works well. We are downsizing and replacing the 6513 core with a 3750G stack. We have the stack up and running in the lab, and want to slowly (as we move floors) migrate all of the edge switching to the 3750 stack.
The plan is to connect the 3750 stack to the 6513, then slowly migrate the edge switches to the stack (from the 6513). I would like to put in place 4 x 1GB trunk links between the 6513 and the 3750 stack before I start moving edge switches to ensure adequate bandwidth. Once all of the edge switches are on the new 3750 stack, I will start to decommission the 6513.
What is the best way to configure the links between the cores (old 6513 and new 3750 stack)? I can easily get the edge switches configured to the 3750, but am worried about the core links. I really want to avoid having to perform an all-at-once cutover of the cores. Another question is when do I try and migrate the VTP server role from the 6513 to the 3750 stack? I could simply make everything transparent, and ditch server-based VTP, as we rarely change or creat VLANs.
View 3 Replies
View Related
Oct 3, 2012
Is it possible to rate limit on a L2 trunk port on a 3750?
current port config and ios are as follows;
interface GigabitEthernet1/0/50
description *** Connection to Fiber Link ***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,172
switchport mode trunk
end
flash:c3750-advipservicesk9-mz.122-46.SE.bin
i was wondering if the "srr-queue bandwidth limit 10" command would work to limit the output from this interface to be 10 % of the port bandwidth and then the same command could be done on the other side.
View 1 Replies
View Related
Mar 18, 2013
I am taking only undersize errors on catalyst 3750 trunk interface (attached some outputs)...the other end is a 4500 switch and the interface is clean..can this be related to any bug ? this is my root port and often leading to trouble sometimes STP BPDUs transportation are affected..
View 4 Replies
View Related
Nov 13, 2012
I have a 3750 as a core and have a series of HP Procurve switches that are daisy chained using one port. I have two vlans on the port now (6 &9) and everything works fine, all switches communicate and end devices on the switches are also talking. There is a requirement to add a device towards the end of the chain which requires it to connect using Vlan1. Once I add Vlan1 to the port onthe 3750 I lose connectivity to all the HP switches.
View 4 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
May 17, 2012
We had a core switch (Cisco 4503), distribution switches(Cisco 3750) and access switches in our network and consists of many vlans. Almost all vlans uses DHCP Pools. But for few vlans DHCP is not yet configured due to initial design poblems. Recently one of the rogue user in vlan 1 connected to one of the access switch send rogue arp packets to the network (suspecting arp packet with interface vlan 1 ip of core switch with wrong mac-address (gateway ip of vlan 1)) and resulted in a prolonged network outage for the vlan 1. Any way we are going to seggregate vlan 1 into different vlans, but before that we need a temporary plan to block such kinds of attack like enabling DAI in the switch. I have checked the DAI implemenation feasibility with my knowledge and found that it is not possible to configure to the access switches(Cisco 2960) in which the user directly connected. But found that Distribution switch connected to that particular access switch seems to be able to configure since DAI commands are available to configure in switch.
Is it possible to block ARP packets with the interface vlan 1 IP Address with rogue mac-address by configuring DAI in the above mentioned Distribution switch and the port connected to the mentioned access switch?
View 2 Replies
View Related
Jan 8, 2013
I am trying to implement in the lab. I have 2 switches 3550 and 3750. my questions are:
1. why i can't see vlans in the running config on switch 3750 even after i created 3 vlans?
2. the 3750 is power over ethernet switch and i am trying to connect 3550 and 3750 thru cross over cable trunk link and the ports doesn't show up no light nothing. is it the right way of cabling.
View 6 Replies
View Related
Feb 12, 2012
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
View 6 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Dec 6, 2012
Two days back my entire network was behaving in unusual ways.When is connect to core switc(4506e) through console. [code]
View 11 Replies
View Related
Jul 21, 2012
I have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?
Is there any tool to perform this task?
View 7 Replies
View Related
Dec 29, 2011
I started having connectivity issues between my core 4506E (Sup7E) and Cisco 2960S. There were input and CRC errors on Te int (SFP 10Gb - LRM) on 2960S, which cause the interface to reset and drop connections. While troubleshooting this issue, I have replaced patch cords and also had the tech checking the fiber. He said that there was some residue on one of the connectors, so the light levels fluctuated in 1300nm, but worked fine in 850. Well LRMs are using 1300, so he re-polished the tips, which worked to stabilize the light levels. After all that, I was still receiving the input/CRC errors, but the connection was NOT dropping. As my last resort I swapped the SFPs between the core and 2960, thinking I should start having issues on the core end. Well, here's what happened: I stopped receiving input/CRC errors on 2960 (also no errors on the core), but 2960s started generating Rx power high alarms: [code]
View 1 Replies
View Related
Dec 8, 2012
I would like to check if it may be possible to hot-upgrade/swap the 4506E power supplies? Based on the configuration guide; I have summarized the steps as follows:
1. Switch has 2 existing power supplies to be upgraded
2. Remove right side/bay 2 power supply and install new power supply
3. At this point; the new power supply will be in err-disabled due to different power supplies on the switch
4. Remove the left side power supply and install new power supply
For item 4; during the removal of the old power supply in bay 1/left side and installation of the new power supply; I am wondering if the switch would lose power even though the new power supply is installed in bay 2?
View 1 Replies
View Related
Oct 31, 2012
I have two cisco 4506-E series switches ..
We are planning to go for HSRP redundancy for 32 VLANs. Means In a Cisco 4506-E switch , we will configure 32 vlans and among them 16 vlans will be primary and 16VLANs will be standby ans it is viceversa in another core-switch
My querie is How many standby groups can we create in Cisco 4506-E switch,
Is there any limitation..
If there is any limitation , can we go ahead with VRRP,GLBP? Are there any limitation in VRRP/GLBP? Is there any design related issue can we face if we use same group number to all VLANs?
Product details :
Model : Cisco 4506-E
Sup Model : WS-X45-SUP6L-E
IOS : S45EIPBK9-12254SG
View 2 Replies
View Related
Dec 12, 2012
I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies
View Related
Sep 10, 2012
I think choose this SWITCH 4506-E and I need running only features L2 Metro, but Idont known what IOS for this!
View 1 Replies
View Related
Apr 22, 2012
I have one 4506E switch working in Lan setup as a core switch with WS-X45-SUP6L-E running ipbase IOS 12.2(54)SG1. Each time after reload the switch we found that the clock is getting reset ( time is getting changed ) where as day, date & year is unchanged.
View 2 Replies
View Related
Apr 4, 2012
how can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies
View Related
Mar 15, 2012
how can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies
View Related
Oct 9, 2012
I have two core switches - 4506E, and i noticed there are frequent cpu spikes on both of the cores switches. As its spikes intermitendly i couldnt able to anlyze the issue. I need inputs on the following,
1) Is there any Free CPU process monitoring tools to identify which process is spiking ?
2) Troubleshooting techniques to identify the issue.
View 1 Replies
View Related
Jun 20, 2012
We have a new building where we added 3 network closets with 3750x stacks.We have 2 fiber gig ports connected to 2 microwave units and etherchanneled the to ports
We have the same setup at the corporate office except the connection is 2 fiber gig ports on a 6509. The 6509 is doing the routing
Now the problem is that we lost the connection to the management interface on only one of the three closets after a few days running. But some workstations at the corp office could reach it... others could not. The workstation were on the same VLAN. We solved the problem for a few days by shutting on of the fiber ports on the etherchannel. But is started happening again... now with PCs being installed at the new location.
The PC that was not working on the 3750x side could ping across to the 6509 but no further then that. It seems like an arp issue not routing because some devices are reachable and fully operational throughout the network.
Here is the configuration:
3750x:Cisco IOS Software, Version 12.2(55)SE1
Current configuration : 118 bytes!interface Port-channel1switchport trunk encapsulation dot1qswitchport mode trunkno snmp trap link-statusend
!interface GigabitEthernet1/1/1description 2gig to STB-6509switchport trunk
[Code]......
View 19 Replies
View Related
Feb 20, 2012
If i try to ssh to a 3750 switch on our 4th floor, it ask's me for a username and password.
After entering the password, it doesnt connect. It shows a blank screen with a flashing cursor.
If i connect to the switch directly via console port, i can see port uplink and downlinks but still cant do anything more.
View 4 Replies
View Related
May 12, 2012
I have a Router 877 and a switch 3750 also a 10 mbps internet connection and I want to share the internet connection to 5 different vlans with a maximum of 2mbps each one or 2 mbps guaranteed. The switch and the router are connected for a trunk port and the vlans are defined in both devices. I have tried many configurations of this with no success.
View 4 Replies
View Related
Apr 2, 2013
I have a 6500 connected to 3750 using fiber connection using patch panel.on the gig port of the 6500 give of error in Input errors, CRC and FRAME.There is no error from the 3750 gigport.
View 6 Replies
View Related
Mar 19, 2012
we using Linksys router for Internet for different vlans now we take 3750 as core switch for another different vlans 10,20 we create v Lans 20,20 also create cpd servers and we need Internet for vlans 10,20 through linksys router how should we configure?
View 5 Replies
View Related
Jun 6, 2013
I have a Cisco SW ( 3560 ) with one Trunk link to my router ( 7606 ), Trunk link is fully utilized so i need to add 2nd Trunk.Shall all move some customers from old trunk to 2nd one and create a new subterface for them ?I am think if i can create bundle and add subinterfaces under this bundle ?Add two GE ports to be memeber of this bundle ?
View 5 Replies
View Related
Jan 5, 2012
We have purchased 3 no CISCO SF300-48P (Access Switches) with the interest of setting up a new laboratory consisting of 120 desktops. We currently have a CISCO 4507R (Core Switch) and a CISCO 3560 (Distribution Switch) for the campus wide network. Our network is developed with various VLANS to support Internet and Intranet facilities. The new lab need to be incorporated in to the Campus wide network with a new VLAN ID. But problem is while trunking the CISCO 3560 (Distribution switch) to the CISCO SF300-48P (Access Switch) communication does not happen. While, surfing the internet and various doc's say that SF300 uses GVRP instead of dot1q trunking.
View 4 Replies
View Related
Mar 19, 2012
We have setup a pair of Nexus 5596 L3 switches with 2 x 10Gbps LACP links between them to act as the vpc peer link. We also have another 2 x 10Gbps LACP links between the 5596 switches to carry non VPC VLANs, this is required to provide EIGRP routing between the switches and an upstream router.I have read that it is possible to setup the vpc keep-alive link over an SVI instead of the management interfaces. Is it ok to run the keep-alive SVI over the second LACP non VPC VLAN trunk or is it recommened to keep this seperate?
View 0 Replies
View Related
Feb 11, 2013
I have 2 hosts, 1 plugged in fa 0/21 in VLAN 101 and another in fa 0/22 in VLAN 101 on our L2 Cisco 2960. If I try and transfer files from either host the gig 0/1 trunk port on the 2960 leading tot he 3750 fa 0/1 port hits 100mb (using a real time bandwidth monitor tool), but why? This VLAN is on the same switch, why does it go one way up the trunk to the L3 3750 switch? The L3 3750 is the VTP server and the 2960 is a client. I would of thought the traffic stays local. The 2 hosts don't even have a gateway set.To sum up the typology the 2960 and 3750 are trunked using a single cable. The 3750 hangs of a ASA firewall using SVIs.Here is whatthe traffic looks like when copying a file between hosts (2gb file).
3750 L3 Switch (VTP Server)
interface FastEthernet1/0/4
description Trunk to Cisco 2960 Gig 0/1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
[code]....
View 6 Replies
View Related
Apr 22, 2012
I have 2 Cisco 6509 switches linked together via single Fibre as a trunk.I want to change this to a port channel where I will add another 3 fibre ports to the port channel but what order do I do this to minimise any disruption.
1-Configure PortChannel and add the 3 new ports, this will bring up the Port Channel but what effect will this have on traffic currently going over the single Trunk link? Will spanning tree go mad, how will switches react?
2-Convert existing Trunk link to Portchannel then add in new ports to PortChannel, I guess in doing this there will be a small hit on traffic as it changes to a port channel.
View 2 Replies
View Related
