Cisco Switching/Routing :: 2960 / Traffic In Same VLAN Goes Up Trunk?
Feb 11, 2013
I have 2 hosts, 1 plugged in fa 0/21 in VLAN 101 and another in fa 0/22 in VLAN 101 on our L2 Cisco 2960. If I try and transfer files from either host the gig 0/1 trunk port on the 2960 leading tot he 3750 fa 0/1 port hits 100mb (using a real time bandwidth monitor tool), but why? This VLAN is on the same switch, why does it go one way up the trunk to the L3 3750 switch? The L3 3750 is the VTP server and the 2960 is a client. I would of thought the traffic stays local. The 2 hosts don't even have a gateway set.To sum up the typology the 2960 and 3750 are trunked using a single cable. The 3750 hangs of a ASA firewall using SVIs.Here is whatthe traffic looks like when copying a file between hosts (2gb file).
3750 L3 Switch (VTP Server)
interface FastEthernet1/0/4
description Trunk to Cisco 2960 Gig 0/1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
[code]....
View 6 Replies
ADVERTISEMENT
Jul 5, 2012
I have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihomed (Broadcom) on the other side an it is supposed to be on this vlan with one of it's network interfaces. We had a pwer outage and now it cannot communicate on this vlan. However, everything else on the vlan can reach all the other nodes accept this server in the front of my building. All the devices in the same room are linked to the same switch which has one port (fa0/17) on vlan0010 and can ping eachother just fine. The server is hooked to port 24 on my server room switch and Gigabit port one goes to a fiber converter all the way to the back. It then gets converted from fiber to cat5e again and links into the switch (2960) in the backroom.
View 5 Replies
View Related
Nov 13, 2011
I am trying to setup a network using Cisco 2960 switches with vlans configured. One vlan will handle video coming from four cameras that are connected to another 2960.
We have four cameras feeeding one port each on a 2960, that 2960 in turn feeds one port on the main 2960 which is the video vlan for that site. From the site it goes back to a Cisco 3750 to be sent over to a Sonicwall firewall. If we connect to the 2960 that the camera are connected to we can see the video, but not on the main site 2960.
View 5 Replies
View Related
May 10, 2012
I've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies
View Related
Feb 9, 2012
We have around a dozen Catalyst 3560 and 2960 switches in a ring topology. We are considering adding storm control to our trunk ports. Up until now we have only used it on edge ports with default values and without error-disable.I am proposing that we also add storm control to trunk ports at a lower level and that we error-disable only the redundant links that make up our loops.
-storm-control broadcast level 25.00 20.00
-storm-control multicast level 2.00 1.00
-storm-control action shutdown [only on redundant links]
In a storm all links will restrict broadcast which should work accessing remote switches, but the redundant links should errdisable and block the redundant path. It is important that the action line is not applied to links that are not redundant as we could isolate parts of the network. Any reason not to use storm control on trunks?
View 2 Replies
View Related
Oct 17, 2012
I have been experiencing discards and no buffers errors on my 2950 switches. These switches are connected to two core switches 4948 and 3560G. I have noticed previous posts regrading these problems but have been unable to find any cases that were resolved. We are using 12.1(22)EA11 software on our 2950 switches.
Outputs:
flrnet3#SH controllers ethernet-controller gigabitEthernet 0/2
Transmit Receive 22204993 Bytes 904542488 Bytes
[Code]....
View 3 Replies
View Related
Dec 25, 2012
I have trunk etherchannel ports 47,48 which both have Vlans allowed on trunk 70,71. Everything works pretty fine. Now I am trying to add a new VLAN 72 to these ports.
conf t
interface FastEthernet0/47
switchport trunk allowed vlan add 72
exit
exit
So far so good. But when making the same command for port FastEthernet0/48 my switch stuck.
View 8 Replies
View Related
Sep 22, 2012
I need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies
View Related
Jan 27, 2013
We bough an Cisco 2911 router, and as i see the "ip sla monitor" command is not supported. Which license/IOS upgrade should i buy the fullfill this. And i cant add a trunkport to the iunterface even cant add a vlan to interface. How do i a trunkport on the cisco 2911 router. ANd how can i do a vlan on a interface on the router.
View 2 Replies
View Related
Dec 6, 2012
can i have 4 links from an ESX server to 6500 , each link represents a trunk link carries each the same 2 VLAN , 100 and 101 , keep port-channel out of the picture , does it work well?
View 12 Replies
View Related
Jan 25, 2012
Need to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
View 1 Replies
View Related
Nov 15, 2011
a number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies
View Related
Nov 8, 2011
Currently we have a 6513 core (running IOS and doing limited routing) with VLAN Trunking to about a dozen 3560 edge switches, with various VLANs going to each of the edge switches. All works well. We are downsizing and replacing the 6513 core with a 3750G stack. We have the stack up and running in the lab, and want to slowly (as we move floors) migrate all of the edge switching to the 3750 stack.
The plan is to connect the 3750 stack to the 6513, then slowly migrate the edge switches to the stack (from the 6513). I would like to put in place 4 x 1GB trunk links between the 6513 and the 3750 stack before I start moving edge switches to ensure adequate bandwidth. Once all of the edge switches are on the new 3750 stack, I will start to decommission the 6513.
What is the best way to configure the links between the cores (old 6513 and new 3750 stack)? I can easily get the edge switches configured to the 3750, but am worried about the core links. I really want to avoid having to perform an all-at-once cutover of the cores. Another question is when do I try and migrate the VTP server role from the 6513 to the 3750 stack? I could simply make everything transparent, and ditch server-based VTP, as we rarely change or creat VLANs.
View 3 Replies
View Related
Nov 13, 2012
I have got 2 Cisco switches (3560G and a 3560X) connected by a trunk port. see config below:
3560G#sh run int gi0/26
Building configuration...
Current configuration : 130 bytes
[Code].....
I can't seem to get VLAN 79 through to the first switch (3560G). Beyond this switch there is a router with acts as default-gateway for the respective VLANs. For VLAN 79 it is 192.168.79.1. I can ping this from the first switch but can't ping it from the second (3560X) switch but can ping 192.168.25.1 which also is the default gateway for this switch.
View 7 Replies
View Related
Jun 6, 2012
I have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
View 5 Replies
View Related
Jan 20, 2012
I need adding a vlan to the trunks bundled in port channel. I know how to add v lans to a port channel with Cisco IOS but with CAT OS.
I have 2 ports bundled to form ether channel in switch which is running CAT OS. There are already few v lans allowed in the trunk of each interface. now I need to add one more v lan.
For Example:-
v lan 135 needs to be added in addition to the existing v lans.
clear trunk1/2 1-112,115,117-134,136-4094
set trunk 1/2 on dot1q 113-114,116,135
and similarly on the 2nd interface
so if I add vlan135 to the trunk one after another will it cause any service disruption?
View 3 Replies
View Related
Nov 13, 2012
I have a 3750 as a core and have a series of HP Procurve switches that are daisy chained using one port. I have two vlans on the port now (6 &9) and everything works fine, all switches communicate and end devices on the switches are also talking. There is a requirement to add a device towards the end of the chain which requires it to connect using Vlan1. Once I add Vlan1 to the port onthe 3750 I lose connectivity to all the HP switches.
View 4 Replies
View Related
Sep 24, 2012
Current Situation:We are able to reach server IP -10.203.206.40 from our 4948 switch vlan 10.30.1.0/24 through the Layer 3 interface between 4506 and 4948.
Requirements
==========
1) Now we would like to add one more L3 interface between 4506 & 4948 for redundancy purpose.
2) Make available Vlan 540 in 4948 from 4506... need to create two trunk links between 4506 & 4948 and allow vlan 540.
View 14 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
Feb 6, 2013
So I took a laptop with wireshark and plugged it into a nexus 5000 port that is configured as a trunk with 3 vlans allowed on it. The laptop was seeing all kinds of traffic on the wire, most of it was not involving my laptop.
For example: Server A VLAN 10= 10.10.10.1 Server B VLAN 20= 10.20.20.1 and wireshark laptop is plugged into a trunk port which is allowing those vlan's. The vlan's are routable.
10.10.10.3 is seeing the entire conversation when 10.10.10.1 backs up 10.20.20.1 even though it has no reason to see it. It is as if the trunk is spanning traffic to the laptop port. No span is setup however. It's really weird. This is not just broadcast traffic, but actual tcp taffic between Server A and B. Why would a trunk port see traffic between 2 other servers talking to each other on the vlan.
Trunk port configuration below:
Interface Ethernet 141/1/3
switchport mode trunk
switchport trunk allowed vlan 10, 20
View 5 Replies
View Related
Jan 2, 2012
I need to implement the shaping VLAN only on the trunk link between the 6500 and 3560. [code]
View 8 Replies
View Related
Oct 11, 2010
Any way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
View 8 Replies
View Related
Feb 9, 2011
I'm not sure if I'm missing something basic here however i though that I'd ask the question. I recieved a request from a client who is trying to seperate traffic out of a IBM P780 - one set of VIO servers/clients (Prod) is tagged with vlan x going out LAG 1 and another set of VIO server/clients (Test) is tagged with vlan y and z going out LAG 2. The problem is that the management subnet for these devices is on one subnet.
The infrastructure is the host device is trunked via LACP etherchannel to Nexus 2148TP(5010) which than connects to the distribution layer being a Catalyst 6504 VSS. I have tried many things today, however I feel that the correct solution to get this working is to use an Isolated trunk (as the host device does not have private vlan functionality) even though there is no requirement for hosts to be segregated. I have configured:
1. Private vlan mapping on the SVI;
2. Primary vlan and association, and isolated vlan on Distribution (6504 VSS) and Access Layer (5010/2148)
3. All Vlans are trunked between switches
4. Private vlan isolated trunk and host mappings on the port-channel interface to the host (P780).
I haven't had any luck. What I am seeing is as soon as I configure the Primary vlan on the Nexus 5010 (v5.2) (vlan y | private-vlan primary), this vlan (y) does not forward on any trunk on the Nexus 5010 switch, even without any other private vlan configuration. I believe this may be the cause to most of the issues I am having. Has any one else experienced this behaviour. Also, I haven't had a lot of experience with Private Vlans so I might be missing some fundamentals with this configuration.
View 3 Replies
View Related
Mar 7, 2012
I am looking into the possibility of using private vlan's for some dmz implementations however I do have what may be some very rudimentary questions. It seems straightforward how to configure the primary/secondary vlan configuration as well as associating them. However in my case I would be looking to configure the PVLAN on a 6500-vss platform acting as the router while all of the hosts which I would desire to have in the isolated vlan would be spread out across a number of older Cisco switches which only support "protected port" setup or Procurve switches all of which I do not have budget to replace with something newer. So in my scenario I would have a 6500 connected by trunk to multiple switches which only support a protected port setup such as a Procurve (top of rack) or a Cisco 2950. As the Procurve or 2950 would not support Private VLAN setup, do I then just configure the secondary vlan to be allowed across the trunk from the 6500, configure that vlan on the Procurve or 2950 (as vtp will not foward the info for the secondary vlan) and assign that vlan to the host port as well as setting it as a protected port and this will communicate just fine across the trunk to the router as well as stopping the protected port in top of rack switch 1 from being able to communicate to a protected port in top of rack 2,3,etc? If the above scenario is what needs to be done, do I just use a regular trunk or do I have to use a PVLAN trunk?
View 2 Replies
View Related
Oct 31, 2012
I want to prioritize egress voice traffic across a trunk terminated on an F1 module, N7K-F132XP-15. I am unsure about the setup; according to the "show interface capabilities" F1 interfaces support 8 egress queues, while the Nexus QoS documentation provides configuration referencing 4 queues. In addition, I am not clear about the relevance of network-qos on F1 queueing setup.
View 1 Replies
View Related
Mar 5, 2012
I have a Cisco 2960 48-port switch. I enter "sh vlan" and it lists all the VLAN's. One of the VLAN's listed is "10" with the name "EPIC". What is the quickest way to find out what ports, if any, are assigned to this VLAN?
View 2 Replies
View Related
Feb 19, 2013
In our network environment, we have a 2960 switch sitting behind our router. Off of this we have a lot of external connections, like our external DNS, firewall, and VPN concentrators. I've configured a VLAN other than the default, moved everything into it and then shut VLAN 1. In this hardening guide it says that your native VLAN should be something other than the user VLAN, but if I am not using any trunk links, wouldn't I not really have a native VLAN? I attempted to make the link to our firewall a trunk link and then set the native VLAN to something else.
View 5 Replies
View Related
Feb 25, 2013
New to Cisco and want to know if I can segment a port. I have two v lans. I have one internet connection at the opposite end of the building. Can the port the internet is connected to serve both V lans?
View 6 Replies
View Related
Apr 16, 2013
Is there a way to block lan to lan traffic (except lan to gateway/gateway to lan traffic of course) on a Cisco 2960?
View 9 Replies
View Related
Feb 12, 2012
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
View 6 Replies
View Related
Mar 13, 2013
I have 2960 cisco switch. I want to configure private vlan. But it is not getting configured in cisco 2960. Is there any other way to configure that in switch.
View 1 Replies
View Related
Aug 6, 2012
I have two questions for a Cisco 2960 (WS-C2960-24TC-L)
1. I am working to setup a few Cisco 2960 switches for HP iLO access to our servers. We are going to segregate the iLO network (VLAN 40) from the data network (VLAN 10) by using a different VLAN. All of the HP servers will be configured with static addresses. My question is, how do I set all the ports to VLAN 40 so that untagged devices will automatically go onto VLAN 40? I don't want to have to configure the VLAN on each iLO port on the server. I tried to set the port to: "switchport trunk native vlan 40", but that didn't work.
2. Also, how do you access the web GUI for these switches? I get a login box, but putting in the enable password doesn't work. I have the following commands in the config: [code]
View 9 Replies
View Related
Jun 6, 2013
we have inserted into a network with VTP a Cisco Switch 2960-S, not knowing that had installed IOS LAN lite.Now I discovered that it can handle up to 64 vlan. In the network there are currently configured 62 VLAN: what happens when we exceeded the max number (64) of VLAN for that switch?
View 6 Replies
View Related
