I have a Cisco SW ( 3560 ) with one Trunk link to my router ( 7606 ), Trunk link is fully utilized so i need to add 2nd Trunk.Shall all move some customers from old trunk to 2nd one and create a new subterface for them ?I am think if i can create bundle and add subinterfaces under this bundle ?Add two GE ports to be memeber of this bundle ?
View 5 RepliesWe have purchased 3 no CISCO SF300-48P (Access Switches) with the interest of setting up a new laboratory consisting of 120 desktops. We currently have a CISCO 4507R (Core Switch) and a CISCO 3560 (Distribution Switch) for the campus wide network. Our network is developed with various VLANS to support Internet and Intranet facilities. The new lab need to be incorporated in to the Campus wide network with a new VLAN ID. But problem is while trunking the CISCO 3560 (Distribution switch) to the CISCO SF300-48P (Access Switch) communication does not happen. While, surfing the internet and various doc's say that SF300 uses GVRP instead of dot1q trunking.
View 4 Replies View RelatedI need to create a trunk between a Cisco 3560 and a Juniper EX4200I am perfectly happy with the the Cisco side and want to only allow 1 vlan across the trunk, which I was going to configure on the 3560 side. Any experience on trunking to a Juniper Ex4200.Looking at the Juniper side it looks like I just set the port as a L2 uplink.
View 3 Replies View RelatedA client of ours has installed an SG300-24P switch and would like to setup a LAG between the SG300 and the 3560 switch we manage for them. They would like the LAG to also pass the voice and two data VLANs currently in use; 5, 10, and 100 respectively. I configured the two ports as an Etherchannel with trunking on the logical port, but no luck. I reconfigured as follows:
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode active
end
[code]....
I see no output when I do show lacp nei. At this point the client is looking to use for the configurations to use as he does not know how to setup the SG300 and it is a switch I have never dealt with. I have found some configurations that I believe would allow a single VLAN across, but nothing I believe will allow the LAG to pass all the VLAN's.
if i have this config:
switch port mode trunk
trunk aloved vlan 50
will travel over this trunk untagged packets? For eg the V LAN 1 is by default native V LAN without tag. If i have created a bog ring with catalyst 3560x switches with no spanning tree on V LAN 1 can be the case of this config a loop ???
I am using upper config on interfaces that are connected the switches together in ring.
Other interfaces on switch have this config:
int range 0/1-4
switchport mode acc
switchport acc vlan1
int range 0/5-24
switchport mode acc
switchport acc vlan50
I am using vlan1 just for local switching without connection to internet! I am asking just because i have this king of messages in logs:
%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on GigabitEthernet1/0/27 (1), with SW3560x_BR8874 GigabitEthernet1/0/19 (50).
GI 1/0/27 and GI 1/0/19 have this config:
switchport mode trunk
trunk aloved vlan 50
We have 7 3560's in 7 different locations connected to our providor for wan access. Our provider has given us a copper cable at each point and we have connected it directly to our 3560 switch at each location. Each port is configured the same way at each location. Each switch is running eigrp.All of the switch ports on each switch are configured as a trunk and vlan 299 had the ip address for the eigrp connection: [code] This setup is working as each switch see's all of the other switches as an eigrp neighbor. We have also made sure that the switch at our head office has spanning tree priority for vlan 299.
So the problem is, if there is a change in the topology at one of the locations it usually causes one or more of the other connections to go down for some reason. We just cannot pinpoint what is causing this change. There are no log's or anything other than an eigrp hold time expired message.?
I have a pair of 3560's configured with dot1q trunks between them carrying a number of VLANs.
Once deployed there will be a requirement for these physical trunks to be disconnected from time to time. Knowing that this is inevitable I am trying to minimise the period of time for the trunks to recover once the physical connectivity is reinstated.
All of the VLANs on the switches are configured for Spanning Tree Rapid PVST. Current time for the trunks/VLANs to come up is around the 4 second mark.
I need to implement the shaping VLAN only on the trunk link between the 6500 and 3560. [code]
View 8 Replies View RelatedAny way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
I recently was asked to turn a routed link between our HQ and our DR Site into a trunked link to allow us to span our main Server VLAN up to the DR Site.I was informed by the ISP that owns the 100Mb Leased Line between the sites that the link was configured to pass dot1q traffic and I should just have to configure my links at either end as trunks to get the link to come up.
There is a Cisco 3560 at either end with Layer 3 routing enabled (obviously as this was a routed link previously).So, I scheduled an outage and configured either end as a trunk links as follows and repointed any routes from the /30 routed addresses to the management addresses of the switches on either side:
***For info VLAN 15 is the DR Site and VLAN 11 is the Server range at our HQ and was available on the connected switch***
interface FastEthernet0/24
switchport trunk encapsulation dot1q
switchport trunk native vlan 15
switchport trunk allowed vlan 11,15
switchport mode trunk
[code].....
Is it possible to use Port Security mechanism between two switch (3750 or 3560) ports while trunk has been configured? If it's not possible, is there any other way to ensure that no other Switch can be connected other then the one switch which has been configured/placed by a network engineer?
View 4 Replies View RelatedWe have setup a pair of Nexus 5596 L3 switches with 2 x 10Gbps LACP links between them to act as the vpc peer link. We also have another 2 x 10Gbps LACP links between the 5596 switches to carry non VPC VLANs, this is required to provide EIGRP routing between the switches and an upstream router.I have read that it is possible to setup the vpc keep-alive link over an SVI instead of the management interfaces. Is it ok to run the keep-alive SVI over the second LACP non VPC VLAN trunk or is it recommened to keep this seperate?
View 0 Replies View RelatedI have 2 hosts, 1 plugged in fa 0/21 in VLAN 101 and another in fa 0/22 in VLAN 101 on our L2 Cisco 2960. If I try and transfer files from either host the gig 0/1 trunk port on the 2960 leading tot he 3750 fa 0/1 port hits 100mb (using a real time bandwidth monitor tool), but why? This VLAN is on the same switch, why does it go one way up the trunk to the L3 3750 switch? The L3 3750 is the VTP server and the 2960 is a client. I would of thought the traffic stays local. The 2 hosts don't even have a gateway set.To sum up the typology the 2960 and 3750 are trunked using a single cable. The 3750 hangs of a ASA firewall using SVIs.Here is whatthe traffic looks like when copying a file between hosts (2gb file).
3750 L3 Switch (VTP Server)
interface FastEthernet1/0/4
description Trunk to Cisco 2960 Gig 0/1
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
[code]....
I have 2 Cisco 6509 switches linked together via single Fibre as a trunk.I want to change this to a port channel where I will add another 3 fibre ports to the port channel but what order do I do this to minimise any disruption.
1-Configure PortChannel and add the 3 new ports, this will bring up the Port Channel but what effect will this have on traffic currently going over the single Trunk link? Will spanning tree go mad, how will switches react?
2-Convert existing Trunk link to Portchannel then add in new ports to PortChannel, I guess in doing this there will be a small hit on traffic as it changes to a port channel.
I am struggling with a CE520 and its smartports stuff.I have configured the following vlans :
1- data
100 - phones
I need to bring those vlans (both of them) to a Cisco 800 router. The port of the 800 router is already configured as trunk and accepts vlan 1 and 100.The cisco 800 has both vlan 1 and 100 configured with 2 ips on different subnets, and ip routing is enable (to route between two vlans). Also, no access lists are configured.I have configured one port in the switch as role "router" and connected to the router. The other ports are all configured as phone-desktop (phone vlan 100 desktop vlan 1).If I connect a phone and manually configure an ip (the phone gets automatically vlan 100), and try to ping the phone from the router, it doesnt respond. Alse vlan 100 is protocol down.I am guessing what s the right configuration as the link between the switch and the router should be a trunk link for 1 and 100 vlans, but it looks like is transporting only vlan 1.Also changing the port role to "other" when you can specify the native vlan and another vlan, the switch doesnt accept vlan 100 as additional vlan on that link.
Cisco 4506-E port configuration
WESTERN-4506-01#show int g4/47
GigabitEthernet4/47 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 0022.554c.01fe (
fe)
Description: Trunk to 425
[code]....
Cisco 3750 Configuration
interface FastEthernet1/0/1description 425Linkswitchport trunk encapsulation dot1qswitchport trunk native vlan 30switchport trunk allowed vlan 30,35switchport mode trunkswitchport nonegotiateswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitystorm-control broadcast level pps 300storm-control multicast level pps 300storm-control action trapmacro description cisco-desktopmac access-group AuthorizedHosts in
I have mac address' populated. I can see the device in layout on CNA with the proper name however cannot ping it.
4506 is 10.30.30.1
3750 is 10.30.30.2
I need to set QOS in our new network. We have connected 2 cities together with 700Mbit leased line. On each side we have Catalyst 2960S switches and between them is TRUNK for VLAN 10 and Vlan 20.Vlan 10 is for IPTV (fixed 400 Mb/s for CATV)Vlan 20 is for Internet (rest).Sometimes is happening that Vlan 20 takes more than 400 Mb/s for a few seconds and in this situation we have problems with CATV.Is there any way to make a guaranteed bandwidth 410 Mb/s for CAT - VLAN 10 on this swithces?
View 2 Replies View RelatedI have a couple 3750 switches that I am trying to run VTP Version 3 on.one as primary and the other as "server" which implies secondary from my research. [code]Additionally, running a show VTP devices yields a "No VTP3 devices found" on both devices. Despite ensuring that the domainname and password match.I have a patch cable from Gi1/0/1 on switch one runnning to Gi1/0/1 which from what I read is acceptable on GigE.
View 2 Replies View RelatedI have connected a 2 TP trunk between 6509 and nx 7000, as shown above. I am trying to have speed 1000 on both sides.If I set speed 1000 on 6509 Trunk disconnect. How to force speed 1000? [code]
View 4 Replies View RelatedI have client who has two distant offices with 3750 L3 as core (do all vlan routing for local office) and multiple L2 access switches with multiple VLAN’s connected to it. First 3750 is hub also connected to internet, second 3750 is spoke and acting as a router on stick. We have eigrp configured on both side ISP provided client 100Mbps link as a trunk with two vlan; vlan10 for voice and vlan20 for data. We assigned two small subnets to these vlans 10.15.17.0/29 and 10.15.17.9/29. Hub addresses are 10.15.17.1 and 10.15.17.9 respectively. How to force voice over VLAN10 and data via vlan20, but still do some load balancing? How to setup default route on second (router on stick) switch?
View 1 Replies View RelatedI have a Cisco 2970 port 24 configured as a trunk port to handle all 11 vlans. This switch is also plugged into a couple other Cisco switches all is good on that side.
Here comes the ODD ball of the bunch. Since our wondeful execs wont let us buy anymore Cisco switches till our numbers get better they gave me this pos Netgear GSM7224. I know this isnt a Cisco product but someone out these has been thru this before.
We bough an Cisco 2911 router, and as i see the "ip sla monitor" command is not supported. Which license/IOS upgrade should i buy the fullfill this. And i cant add a trunkport to the iunterface even cant add a vlan to interface. How do i a trunkport on the cisco 2911 router. ANd how can i do a vlan on a interface on the router.
View 2 Replies View RelatedI have a test switch (Cisco 3550) that I want to set up with 6 Vlans and 2 trunk ports. I want to be able to access a virtual server conected to the trunk ports from the switch ports. Ports Fa0/1 to 8 are in a vlan port fa0/9 to 16 another vlan etc. Ports Fa0/47 and 48 are the trunk ports. This is a lab environment so the the switch is the only device being used.
View 4 Replies View RelatedI've previously used trunkports and vlans between my ASA and accesspoints, connected directly. Now I want to put a 2960S-24PS-L bewteen. Where should i define the vlans (in the switch or in th ASA?) and what ports to put in trunk mode? (the ones on the switch or the one between the switch and the ASA?)
View 1 Replies View RelatedI need to configure a pvlan trunk on DELL enclosure with Cisco Blade Switch, to permit pvlan and a normal Vlan.But, when I want to enter "Trunk" on private vlan mode, I can´t, because only has "host" and "prominiscous" mode. [code]
View 3 Replies View Relatedcan i have 4 links from an ESX server to 6500 , each link represents a trunk link carries each the same 2 VLAN , 100 and 101 , keep port-channel out of the picture , does it work well?
View 12 Replies View RelatedWe have Cisco 4948 switches running in production. We want to moniter the trunk link through SNMP.If trunk link fails SNMP need to send notification to server.
View 1 Replies View RelatedI have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihomed (Broadcom) on the other side an it is supposed to be on this vlan with one of it's network interfaces. We had a pwer outage and now it cannot communicate on this vlan. However, everything else on the vlan can reach all the other nodes accept this server in the front of my building. All the devices in the same room are linked to the same switch which has one port (fa0/17) on vlan0010 and can ping eachother just fine. The server is hooked to port 24 on my server room switch and Gigabit port one goes to a fiber converter all the way to the back. It then gets converted from fiber to cat5e again and links into the switch (2960) in the backroom.
View 5 Replies View RelatedNeed to limit the amount of bandwidth a specific VLAN can use on a 802.1q trunk port. Situation is that we have a pair of Catalyst 4506 switches which have 802.1q trunk ports into a Checkpoint Firewall, this in turn is connected to a managed WAN router (to which I can't apply a QoS policy).If the 4506 was routing the traffic it would be easy to setup a class-map to match the IP traffic and then QoS the traffic, but the VLAN in question is trunked directly into the firewall (no L3/IP presence on the 4506 next hop for all clients on this VLAN is the firewall).What I need to do is restrict any traffic from this specific VLAN to 10Mbps on the uplink to the Checkpoint Firewall so it cannot impact the onward WAN.
View 1 Replies View RelatedI understand that jumbo frames need to be enabled end-to-end. I have two ESX hosts connected at each site. I want to enable jumbo frames for those ports, but what if not all host on the ESX are using jumbo frames, will I have drops and connection failures? So if i have two sites, each with a 6509 connected via a trunk and need to enable jumbo frames for a vlan between the sites how do I accomplish this?If I enable jumbo frames on the trunk link how does that impact other traffic between the sites?
View 3 Replies View RelatedI've been having a debate with a colleague about QOS COS values. My colleague says I need to use COS values across layer 2 trunk links between access layer switches and core switches. My argument is if phones are marking packets with DSCP values I don't need to be concerned with Cos.The reason I ask is we're implementing a new phone system, the ip phones will mark RTP traffic wih dscp value EF and Call signaling with DSCP value of CS3. If my understanding is correct I can trust the dscp values of the phones. We are using Cisco 4507 switches which I believe automatically trust dscp values so I would just need a class-map to match the dscp values and apply the output policy map on the egress interfaces as follows? [code]
View 3 Replies View Relateda number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies View Related