Cisco Application :: NME-WAE-502-K9 Doesn't Want To Boot
Dec 16, 2012I have added a new NME-WAE-502-K9 in one of our remote Cisco 2811 routers. This module doesn´t boot, and it seems to be in a loop trying to boot. [code]
View 6 Replies
ADVERTISEMENT
Cisco Firewall :: WS-SVC-FWM-1-K9 Doesn't Boot
May 9, 2011I'm having an issue, with an WS-SVC-FWM-1-K9.
The card doesn't boot properly, it tries to boot, but after a while the 6500 puts it in shutdown.
I've noticed that it has 2 RJ45 ports in the board, I've plugged my console cable, but i only get characters with the default serial configuration.
Any information about the port configurations? Is the port "PC Console" the correct one?
Cisco WAN :: 3825 Failure - Doesn't Seem To Boot
Nov 13, 2011I have a remote customer who is having issues with their 3825 router - since I can't be on site troubleshooting is difficult but so far all that seems to happen when the device is powered on is the "SYS PWR" light goes solid green, and no other lights come on. Fans seem to be operating normally. Console access doesn't appear to be working.
View 2 Replies View RelatedCisco Wireless :: After Upgrade WLC 4402 Doesn't Boot
Jun 10, 2013I wanted to upgrade our three WLC 4402 from software version 5.0.148 to 6.0.202.0. The upgrade on the first controller was working. Unfortunately he lost all the local management users and it's MAC filters, but restoring this was not the problem. After upgrading the second controller.... the device does not boot anymore! The alarm led is RED and I don't know what to do. The only way to get connected to the controller is via the console port. There I can see a "parse error" but I don't know if that is the problem. Please look at the "log" attached. I'm not sure if the red alarm led was there before upgrading the controller software because the device is located to another place. I'm really concerned about upgrading the third controller because it's the most important wlc.
View 3 Replies View RelatedLinksys Cable / DSL :: WAG160N Router Doesn't Appear To Boot
Jan 28, 2013Last night we had some pretty bad lightning and thunder and our Linksys WAG160N appears to have had a bit of a fright.As I was going round unplugging items in case of a hit (this was after a flash or two, relatively nearby), all the lights on the router were off except for the ethernet light (plugged into a Linksys homeplug adaptor). Now the router doesn't appear to boot. When powered on, the power light doesn't flash or anything to indicate booting up, all you get is the ethernet light (if connected) after a few seconds, but no activity. I'm presuming something has been fried or corrupted? I'm not sure if we did have a power spike either through the mains or phone line as all other equipment seems to be fine, but I'm wondering the the homeplug connection might of had something to do with it after reading a few posts from others on the subject.I've held in the reset button while starting and it doesn't appear to have done anything. I will try the 30/30/30 reset tonight.
View 1 Replies View RelatedCisco Switching/Routing :: 3750x Doesn't Boot After Upgrade To Version15
Apr 22, 2013Due to a problem with POE+ i have tried to upgrade the IOS to Version15.0.2SE2, from 12.2.58. unfortunatly the Switch doesn't boot up anymore. It starts to decompress and install the IOS 2 Times, after the Second try it displays "unable to boot" and the switch goes in Bootloader-mode. When i look at the version i See that bootloader is still the old version 12.2.58. It seems that the bootloader doesn't geht upgraded and that's why the Switch can't Boot the new Image.
View 8 Replies View RelatedCisco Switches :: SRW224G4 V1.1 After Power Brake Our Switch Doesn't Boot Anymore
Aug 15, 2012We have small network with 15 Computers all connected to SRW224G4 . After a power brake our switch dosent "boot" anymore. I see all leds working flashing etc but no network acces, no Serial acces. When i try connecting to serial port and "reset" device the screen is blank.
View 1 Replies View RelatedCisco Firewall :: 5500 Blocking Skype Application Doesn't Work With ASA CX
May 12, 2013I'm trying to build different content security scenarios for a potential deployment of ASA5500-X series firewall with CX module and ran into a trivial problem. A simple access policy has been configured to deny Skype. It's as simple as it sounds. To my surprise I don't see that it is being enforced.I have all my pending changes committed, events are now showing with hits, see attached print screens. Tried to start Skype on my PC with the source shown on the print screen it and don't see any effects of this policy.
As a side note, I know for sure that other type of filtering does work, i.e. I have configured a deny filter for gambling URL category and it seems to work nicely.
Cisco Application :: ACE20 - Config Application In Progress Message
Dec 3, 2012Everytime I make a config change to one of the contexts on our ACE20, I get this message: Config Application in Progress. This command is queued to the system
If I run show download info, I get:
context : context1
Interface Download-status
--------------------------------------------------------------
187 In Progress
199 Pending
Regex download optimization status : Couldn't get status[TNRPC Timed out]
It eventually seems to complete, but it takes a very, very long time. We are running Version A2(3.5) [build 3.0(0)A2(3.5)].
Cisco Application :: Application Slowness Through ACE 4710
Mar 27, 2013Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies View RelatedCisco :: Application Layer Service The Same As Application Layer Software?
Apr 3, 2012I am taking an introduction class to CCNA and we are focusing on the Application Layer,and I'm having some difficulty in understanding what is an Application Layer Service. Is the Application Layer Service the same as Application Layer Software?
View 3 Replies View RelatedHow To Boot PC From LAN
Sep 23, 2011I Want To Boot PC From LAN.
View 2 Replies View RelatedCisco :: 6500 VSS - NAM Does Not Boot
Jun 21, 2011We have got a big problem with our NAM (WS-SVC-NAM-1) - it does not boot. We have got a second one and in an other chassis. I changed the chassis, and RAM and Flash from the other one. RAM and Flash are ok.
We checked the disc (hardware) with an Ontrack-tool -it is OK.
environment: 6500 VSS
sh logging:
Jun 17 13:18:24: SW1_SP: Switch 1 Physical Slot 7 - Module Type LINE_CARD inserted
sm(cygnus_oir_bay slot7), running yes, state wait_til_online
Last transition recorded: (offline)-> empty (remove)-> empty_clr_persist (remove)-> empty (insert)-> may_be_occupied (timer)-> occupied (known)-> can_power_on (yes_power)-> powered_on (real_power_on)-> check_power_on (timer)-> check_power_on (power_on_ok)-> wait_til_online
Cisco WAN :: 1812 Usb IOS Boot?
Sep 29, 2011is it possible to boot the image from a usb stick on a 1812? if so, what are the requirements?
View 14 Replies View RelatedCisco WAN :: 2621 - IOS Boot
Aug 22, 2012I've got a Cisco 2621 with this IOS image in flash: c2600-i-mz.120-7.bin (the only IOS in flash). When I power up the router, the following errors occur:
open: file "n" not found
open(): Open Error = -1
loadprog: error - fileopen
boot: cannot load "flash:n"
I have to press "Ctr l" and "break" to enter Roman, there i can use the boot command to start the IOS. Configuration register is set to 0x2102, all running config should be factory default.
What I have to do to boot the IOS directly when i power up my router (without entering Roman mode...)?
I Want To Boot My Network
Feb 13, 2011want to boot my network how can i do that?
View 1 Replies View RelatedHow To Boot From Another Computer's DVD ROM Via LAN
Apr 2, 2013I have a netbook, so it have not dvd drive. I haved usb flash drive, but now it not work. I want to install windows on my netbook, but i cant as there are no dvd drive and flash drive.But i have a PC computer, which have dvd drive.I want to know, that is it possible to boot my PC's dvd rom and install windows on my netbook.
View 14 Replies View RelatedCisco :: Boot From Tftp Failing?
Aug 5, 2011I've got a fully working 877w that I'm trying to get to boot from tftp, but I just can't seem to get that going.I have a tftp server running and can copy images back and forth without any trouble.I have this in my config:boot-start-markerboot system tftp c870-advipservicesk9-mz.124-24.T2.bin 192.168.1.200boot-end-markerDuring the boot process I get an error message that says there is a missing or illegal ip but I really don't see how that can be as my tftp server is 192.168.1.200 just like my config says.
View 16 Replies View RelatedCisco Wireless :: WLC AIR-CT2504-K9 Cannot Boot
Jun 5, 2013I have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
Cisco Wireless :: Cannot Boot WLC 2106
Apr 20, 2010I have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
Cisco Firewall :: ASA 5505 Is Not Boot Up
Jul 29, 2010My ASA5505 is not boot up. I did upload ios from rommon mode with tftp and tftpdnld.It is uploaded successfully after reboot it stopped at cisco logo sing.
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
I deleted old ios and upload new but look same.
Cisco Wireless :: 1131AG AP Not Able To Boot
May 31, 2012My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
Cisco WAN :: 877 No Boot File / But Appears To Have IOS
Feb 7, 2013I have two 877's that have both reset with the following messages on boot, and dir of flash and lost+found/It appears that there is a IOS on the flash? but rommon doesn't know where it is. I tried to "set" with no luck as set is read.
I have noticed that the IOS is 0 size. [code]
Cisco :: 2800 - IOS TFTP Boot
Feb 6, 2012I need Cisco router 2800 series boot ios image from network(tftp), when flash is corrupted or router doesn't see it, so it is impossible ? Command, i used boot system tftp: ios.bin but this does not work.
View 9 Replies View RelatedCisco WAN :: Error On 1921 Boot-up?
Dec 11, 2012I purchased several 1921 routers and the last two I setup get the following error during bootup:
%SYS-6-READ_BOOTFILE_FAIL: tftp://255.255.255.255/1:aaa1386.bin No usable interfaces.
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
%MAINBOARD_GE-3-SHUTDOWN: FPA PKT pool holding 512 particles.boot of "1:aaa1386.
bin" using boot helper "usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" failed
error returned: No usable interfaces
loadprog: error - on file open
boot: cannot load "1:aaa1386.bin"
The router moves on and eventually comes up fine and is operational. What this error is an if I can get rid of it?
Cisco :: 1841 - Router Won't Boot Up
Feb 24, 2012I have a problem with 1841 router - It wont't boot up and there is a message
Correcting primary nv_flash
Cisco WAN :: Error During Boot IOS On ASR1002?
Dec 27, 2011During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
Cisco WAN :: 1841 Boot Failure
May 18, 2011we have a problem with a Cisco 1841 router while booting. The router is loading the image from the CF card but gets stucked at this point:
This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be foundURL
Cisco Firewall :: Upgrade Pix 525 Boot Rom From 4.0 To 4.3?
Feb 22, 2012how to upgrade a Cisco Pix 525 boot rom from 4.0 to 4.3. Is it a physical chip or software upgrade? Is it needed to upgrade to latest IOS on Cisco Pix 525 to 8.0. Where can I find more information on it?
View 1 Replies View RelatedCisco :: Getting DHCP Client Messages On Boot
Apr 25, 2013I have a Cisco ASA 5505 I've configured as a DHCP server. I'm getting DHCP on workstations attached to the appliance, but I'm getting the following message when the appliance loads:DHCP Client: can't enable DHCP Client when DHCP Server/Relay is running on the interface DHCP: Interface 'inside' is currently configured as SERVER and cannot be changed to a CLIENT by a CLIENT featureI'm not trying to configure this thing as a client, so I'm not sure why the system is producing this message.
View 2 Replies View RelatedCisco :: Switch Power Usage On Boot?
Oct 11, 2011I have a customer who is concerned with the power draw on the new switches we're deploying.They only have 20 amp breakers in their closets and fear popping them on switch boot. The customer is under the impression that a switch will pull full power on boot. So a 3560X with an 1100w PSU will draw the full 1100w on startup. Ive never heard this and it doest make much sense to me, but I need to verify.
View 10 Replies View RelatedCisco :: 2621 Router In Boot Loop?
Jul 27, 2011I have a 2621 router, because I want an image of about 21M, I upgraded as follows:
IOS = 32M
RAM = 64M
ROM VERSION = 12.2
However, when I power up my router, it goes into a boot loop, and I see the following messages:
NOT ENOUGH MEMORY IN THE SYSTEM TO RUN THIS IMAGE
***SYSTEM RECEIVED A SOFTWARE FORCED CRASH***
how to overcome this error, and successfully upgrade, so I could load my new image?
Cisco WAN :: C2960 Boot Image After Ios Upgrade
Dec 30, 2011 i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
