how to upgrade a Cisco Pix 525 boot rom from 4.0 to 4.3. Is it a physical chip or software upgrade? Is it needed to upgrade to latest IOS on Cisco Pix 525 to 8.0. Where can I find more information on it?
View 1 Replies i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
I upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
I wanted to upgrade our three WLC 4402 from software version 5.0.148 to 6.0.202.0. The upgrade on the first controller was working. Unfortunately he lost all the local management users and it's MAC filters, but restoring this was not the problem. After upgrading the second controller.... the device does not boot anymore! The alarm led is RED and I don't know what to do. The only way to get connected to the controller is via the console port. There I can see a "parse error" but I don't know if that is the problem. Please look at the "log" attached. I'm not sure if the red alarm led was there before upgrading the controller software because the device is located to another place. I'm really concerned about upgrading the third controller because it's the most important wlc.
View 3 Replies View RelatedAfter performing a firmware upgrade on an SG300-20 switch from ver 1.1.0.73 to 1.2.5.70 the switch now boots up with the following error and resets:
30-Aug-2011 10:47:33 %L1Mngr-F-PARAMTOOLONG: csco-sb parameter %s is too long.
The attached file contains a full output of the console boot process. I have tried loading different versions from the console, but all produce the same error.
I HAD similair problem:[URL](Have ver 1.1) Forgot password. Restored to v1.0.0.86 via telnet Been playing around with telnet AND web based updates Read somewhere else (Web-based ONLY works with IE) (Tried Web-based and keep getting "Copy Failed/Undefined Error" and 0 Bytes transfered) Know to upgrade "Boot" first, then "Software Image" THEN reboot
Tried telnet (not through web-based startup) Can get to "lcli" (by Ctrl+Z twice)Retyped Username and Password:
At "console#" tried typing "copy tftp:///srw2024_16_boot-101.rfb boot" didn't work : "Must be valid URL or reserved keyword"
Where am I going wrong?
How do I upgrade the boot rom version on the 7200 router? I am running IOS Version 12.4(22)T and when I plug in the serial ds3 card in my router it keeps rebooting with a watch dog error ( see below). Also, what version should I upgrade to?
Router#sh verCisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Fri 10-Oct-08 10:10 by prod_rel_team
ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router uptime is 0 minutesSystem returned to ROM by power-onSystem image file is "sup-slot0:/c7200-spservicesk9-mz.124-22.T.bin"
[code]....
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedDue to a problem with POE+ i have tried to upgrade the IOS to Version15.0.2SE2, from 12.2.58. unfortunatly the Switch doesn't boot up anymore. It starts to decompress and install the IOS 2 Times, after the Second try it displays "unable to boot" and the switch goes in Bootloader-mode. When i look at the version i See that bootloader is still the old version 12.2.58. It seems that the bootloader doesn't geht upgraded and that's why the Switch can't Boot the new Image.
View 8 Replies View RelatedI've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies View RelatedI'm having an issue, with an WS-SVC-FWM-1-K9.
The card doesn't boot properly, it tries to boot, but after a while the 6500 puts it in shutdown.
I've noticed that it has 2 RJ45 ports in the board, I've plugged my console cable, but i only get characters with the default serial configuration.
Any information about the port configurations? Is the port "PC Console" the correct one?
My ASA5505 is not boot up. I did upload ios from rommon mode with tftp and tftpdnld.It is uploaded successfully after reboot it stopped at cisco logo sing.
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
I deleted old ios and upload new but look same.
I have a Cisco ASA 5510 with a strange issue. When I power it ON, the following is the status of the front panel LED:
Power is OFF
Status is Amber
Active is Amber
VPN is Green
Flash is OFF
Also nothing comes up on the console. I suspected a Power supply issue and replaced it, but still it doesn't seem to work.I cant open up a TAC as I do not have a Smart Net contract.
When I power on our ASA 5510 it just hangs on "Launching BootLoader...".
I've managed to get into ROMMON before it attempts to launch the bootloader and tried to restore an ASA image but it said disk0: failed to mount.I've copied the console output but am not sure if it is useful to diagnose the problem or not (and is quite long)
I have 7604 router with FWSM module in module 3.First of all the FWSM CF has been damaged, not physically. I bought the new same compact flash (size, partnumber, etc.). Downloaded the software 3.2 for FWSM, and ASDM from Cisco website. I realized that the procedure of creating new CF for FWSM is quite diffucult: creating 1-5 partitions, where 1 - is MP, and 4th - application partition. According to cisco documentation - the default boot partition is the 4th, so I partitioned from 7604 the CF into 4 partitions (partition disk1: <1-4> maximum) and copied the software and ASDM to the 4th partition (disk1:3:). Removed the CF from the router and put it into the FWSM module.
View 1 Replies View RelatedI have an ASA 5505 that I was updating from frimware 8.04 to 8.41. Anyway, I went through the update procedure half-asleep and accidentally deleted the boot image right after I installed it (I used the CLI and put in the command del asa8*.bin then just hit enter a bunch of times, which of course means I deleted the old firmware too).
So now whenever I power up the ASA, I get the "Could not find boot file" error. Is there a guide somewhere that tells me how can upload another boot image to the ASA and set the ASA to boot it from teh ROMMON prompt?
I have a problem getting my ASA 5520 boot properly. I first though of a flash problem and did a flash erase in ROMMON, then it brought error 15 during boot (No images found in / Error 15: File not found). I then TFTPied and image from Rommon, when done loading the image and start booting, the system hangs and nothing else. Attached is the screen I got on my console during boot up. BTW, the system was in the same state before I undertook any of the above actions. I don't have a service contract, so I can't contact TAC.
View 3 Replies View RelatedI'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.
View 2 Replies View RelatedI have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
i have cisco ASA 5510 Firewall using in my network, i have planning to upgrade the Flash memory from 256 mb to 512 mb and the RAM from 256 mb to 1GB.
View 1 Replies View RelatedI have recently gone to upgrade my firewall to version 8.4.4, but afte i upgraded this all the network objects have all got jumpled up, lost there descriptions lost there names and there are some duplicates.
View 1 Replies View RelatedUpgrading from 7.2 to 8.4 cisco ASA rewrite itself commands? Nat for example is different from 8.3/8.4 right?
View 4 Replies View RelatedI am upgrading a active/standby pair of asas 5520's from 8.4.1 to 8.4.5. I am wondering if there is anything i need to be careful of. I do use a lot of Nat policys and i have had issues with 8.4.1 and proxy arp so i hard coded alot of my nat ip's.is there a good procedure? I want toupgrade one and keep one shut down while i test all my applications and connectivity and then bring it back online and upgrade it.
View 3 Replies View RelatedI have never touched a firewall box before but i need to upgrade the IOS on 2 ASAs that are running in production. I am upgrading from 8.2(2) to 8.2 (5). Just to point out, one of the firewalls is having SSM module with it. Below in the end is the "sh inventory" output.I have downloaded the asa825-k8.bin and asdm-645-106.bin files already on my computer. Two queries to clear off:
1. Wanted to know if I need to download any more files. Like some feature licenses or anything else? I did "dir flash: to see what contents it had already and this was it:
28 -rwx 16275456 02:18:46 Nov 07 2010 asa821-k8.bin
129 -rwx 11348300 04:34:32 Nov 07 2010 asdm-621.bin
3 drwx 4096 08:03:46 Jan 01 2003 log
10 drwx 4096 08:04:00 Jan 01 2003 crypto_archive
11 drwx 4096 08:04:32 Jan 01 2003 coredumpinfo
2. How to I take a complete backup like it works in ASDM v6.2 "Tools->Backup configurations". I was reading thru the RN for doing that and what I could understand, it was talking about some "export" thing but it did not make much sense to me.Below is the sh version and sh inventory from both the ASAs?
FW01# sh ver
Cisco Adaptive Security Appliance Software Version 8.2(1)
Device Manager Version 6.2(1)
Compiled on Tue 05-May-09 22:45 by builders
[code]....
I'm upgrading an ASA from 7.2.4 to 8.2.5 due to memory requirements for 8.3. My question is should I upgrade to 8.2.5 or to the interim for 8.2.5. I would prefer not to upgrade to 8.2.5 and then hit the bug for the ASA leaving connections open and then have to upgrade to the interim anyway. But I know that it is advised not to upgrade to interim levels unless you have specific requirements or issues to fix.
View 2 Replies View Relatedwe have ASA 5510 which we need to upgrade from 8.0(3) to 8.2.5. can we directly switch to 8.2.5 from 8.0(3) , if not what all versions we need to go from.
What all point needs to check before that following is show flash output.
97 14635008
Jan 01 2003 14:12:16 asa803-k8.bin 98 4096
May 14 2008 21:22:10 tmp 2 4096
Apr 20 2008 02:21:46 log 6 4096
Apr 20 2008 02:22:16 crypto_archive 99 6851212
[Code] .....
My customer has a rather complex configuration on an ASA 5510 running version 8.2.
They are migrating to new ASA 5515X models which of course only version support 8.6
How can i convert the configuration from 8.2 to 8.6 since the new ASA's do not support the earlier versions?
The X series seems to be a great option for new deployments but what about replacements of existing older models?
I am having ASA5510 firewall which has 1GB RAM currently. I want to upgrade to 2GB. When I opened the box, I can see only 1 slot to insert the RAM. I searched in Cisco website and I got to know that I need to use 2 x 1 GB RAM. So, I need to have 2 slots to do that. But, I am having only 1 slot in the box.
View 5 Replies View RelatedWe have 2 x ASA5520 and I upgraded this to 8.2.2 last year, I see 8.2.5 and now 8.4 is out. If we are having no issues, is it best just to leave it as it is? I can see a couple of features I may find useful in 8.2.5, but 8.4 seems like a huge jump and a risky one too.
View 1 Replies View RelatedIs it possible to upgrade directly from 8.0(4) to 8.2(5) software in 5510. Is there be any workaround in regards to the config.
View 3 Replies View RelatedI'm getting ready to reload an ASA that will be a long drive if it doesn't come back up after this upgrade attempt.
View 9 Replies View RelatedWe are about to upgrade our ASA's from 7.04 to 8.2. Obviously I will be opening a TAC case to assist with the upgrade and I will also be upgrading ASDM software at the same time. These production firewalls are paired with an active --> failover scenario and not active --> active. I had previously engaged cisco regarding the upgrade and they have recommended an upgrade path to ensure success. Also, I have a pair of test ASA's that I've gone through the upgrade process with - documenting the changes in commands and any changes in my config (I didn't notice any).So, the reason for my post is this: What are the gotcha's that you may have run into when upgrading your ASA's?These are fairly high visibility ASA's and any downtime due to the upgrade needs to be mitaged as much as possible.
View 1 Replies View Related