Cisco WAN :: 1841 Boot Failure
May 18, 2011
we have a problem with a Cisco 1841 router while booting. The router is loading the image from the CF card but gets stucked at this point:
This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be foundURL
View 1 Replies
ADVERTISEMENT
Nov 13, 2011
I have a remote customer who is having issues with their 3825 router - since I can't be on site troubleshooting is difficult but so far all that seems to happen when the device is powered on is the "SYS PWR" light goes solid green, and no other lights come on. Fans seem to be operating normally. Console access doesn't appear to be working.
View 2 Replies
View Related
Sep 14, 2011
i'm trying to re-image an asc se 1113 with a recovery cd but i keep getting a disk error complaining of an invalid destination drive
View 1 Replies
View Related
Dec 20, 2012
I have 7604 router with FWSM module in module 3.First of all the FWSM CF has been damaged, not physically. I bought the new same compact flash (size, partnumber, etc.). Downloaded the software 3.2 for FWSM, and ASDM from Cisco website. I realized that the procedure of creating new CF for FWSM is quite diffucult: creating 1-5 partitions, where 1 - is MP, and 4th - application partition. According to cisco documentation - the default boot partition is the 4th, so I partitioned from 7604 the CF into 4 partitions (partition disk1: <1-4> maximum) and copied the software and ASDM to the 4th partition (disk1:3:). Removed the CF from the router and put it into the FWSM module.
View 1 Replies
View Related
Feb 12, 2011
I've tried to upgrade firmware through chrome, but chrome abruptly shut down during upgrade.Since that, I have not even loggin set-up menu which should be shown up putting 192.168.0.1 to make it back. Amber light is just blinking on Power lamp.
View 2 Replies
View Related
Feb 24, 2012
I have a problem with 1841 router - It wont't boot up and there is a message
Correcting primary nv_flash
View 2 Replies
View Related
Jul 4, 2011
Getting message, cannot open "flash:" on 1841 evdo router, how do I reinstall flash? I am currently consoled into the router, the prompt is coming up as rommon 1>
View 1 Replies
View Related
Oct 17, 2012
I have a 2851 and a 1841 both serving as hub routers in a GRE multipoint configuration. They are both receiving buffer misses and failures on startup. I will post the output of show buffers below:
LAB-HUB-RTR#show buffers
Buffer elements:
607 in free list (500 max allowed)
9071 hits, 0 misses, 618 created
Public buffer pools:
Small buffers, 104 bytes (total 71, permanent 50, peak 71 @ 00:11:33):
68 in free list (20 min, 150 max allowed)
7083 hits, 74 misses, 0 trims, 21 created
55 failures (0 no memory)
[code]....
I have tried increasing the small/medium buffers initial size and permanent size, however there is no change. The buffer failures for small and medium buffers are always around this many every boot.I have also changed the IOS versions between 12.4.24(T4) to 15.1 with no luck in stopping the failures.
View 1 Replies
View Related
Jan 12, 2013
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies
View Related
Jan 10, 2012
I know that CW Common Services 3.3 does not work with pre-defined roles on ACS AAA. So I followed these forums and enabled non-ACS AAA and selected TACACS+. I have a single rule that is matching in my ACS (after looking at the audit trail):
Authentication Details
Status:
Passed
[Code]....
As you may have noticed even though it is matching an access service that allows Priv15. That doesn't seem to be passing through as you can see on top I am only receiving Priv 1. What can I do to properly pass through the access service profile?
View 2 Replies
View Related
Sep 23, 2011
I Want To Boot PC From LAN.
View 2 Replies
View Related
Jun 21, 2011
We have got a big problem with our NAM (WS-SVC-NAM-1) - it does not boot. We have got a second one and in an other chassis. I changed the chassis, and RAM and Flash from the other one. RAM and Flash are ok.
We checked the disc (hardware) with an Ontrack-tool -it is OK.
environment: 6500 VSS
sh logging:
Jun 17 13:18:24: SW1_SP: Switch 1 Physical Slot 7 - Module Type LINE_CARD inserted
sm(cygnus_oir_bay slot7), running yes, state wait_til_online
Last transition recorded: (offline)-> empty (remove)-> empty_clr_persist (remove)-> empty (insert)-> may_be_occupied (timer)-> occupied (known)-> can_power_on (yes_power)-> powered_on (real_power_on)-> check_power_on (timer)-> check_power_on (power_on_ok)-> wait_til_online
View 2 Replies
View Related
Sep 29, 2011
is it possible to boot the image from a usb stick on a 1812? if so, what are the requirements?
View 14 Replies
View Related
Aug 22, 2012
I've got a Cisco 2621 with this IOS image in flash: c2600-i-mz.120-7.bin (the only IOS in flash). When I power up the router, the following errors occur:
open: file "n" not found
open(): Open Error = -1
loadprog: error - fileopen
boot: cannot load "flash:n"
I have to press "Ctr l" and "break" to enter Roman, there i can use the boot command to start the IOS. Configuration register is set to 0x2102, all running config should be factory default.
What I have to do to boot the IOS directly when i power up my router (without entering Roman mode...)?
View 4 Replies
View Related
Jul 16, 2011
In our company we are using Ciscoworks LMS3.0.( DFM 3.0.1, RME 4.1.1.) In DFM, every day at 8:00 PM we receive alarm authorization failure on Core switch ( source is cisco works server IP).
View 6 Replies
View Related
Feb 13, 2011
want to boot my network how can i do that?
View 1 Replies
View Related
Apr 2, 2013
I have a netbook, so it have not dvd drive. I haved usb flash drive, but now it not work. I want to install windows on my netbook, but i cant as there are no dvd drive and flash drive.But i have a PC computer, which have dvd drive.I want to know, that is it possible to boot my PC's dvd rom and install windows on my netbook.
View 14 Replies
View Related
Aug 5, 2011
I've got a fully working 877w that I'm trying to get to boot from tftp, but I just can't seem to get that going.I have a tftp server running and can copy images back and forth without any trouble.I have this in my config:boot-start-markerboot system tftp c870-advipservicesk9-mz.124-24.T2.bin 192.168.1.200boot-end-markerDuring the boot process I get an error message that says there is a missing or illegal ip but I really don't see how that can be as my tftp server is 192.168.1.200 just like my config says.
View 16 Replies
View Related
Jun 5, 2013
I have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
View 2 Replies
View Related
Apr 20, 2010
I have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
View 4 Replies
View Related
May 9, 2011
I'm having an issue, with an WS-SVC-FWM-1-K9.
The card doesn't boot properly, it tries to boot, but after a while the 6500 puts it in shutdown.
I've noticed that it has 2 RJ45 ports in the board, I've plugged my console cable, but i only get characters with the default serial configuration.
Any information about the port configurations? Is the port "PC Console" the correct one?
View 3 Replies
View Related
Jul 29, 2010
My ASA5505 is not boot up. I did upload ios from rommon mode with tftp and tftpdnld.It is uploaded successfully after reboot it stopped at cisco logo sing.
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
I deleted old ios and upload new but look same.
View 16 Replies
View Related
May 31, 2012
My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
View 3 Replies
View Related
Feb 7, 2013
I have two 877's that have both reset with the following messages on boot, and dir of flash and lost+found/It appears that there is a IOS on the flash? but rommon doesn't know where it is. I tried to "set" with no luck as set is read.
I have noticed that the IOS is 0 size. [code]
View 2 Replies
View Related
Dec 16, 2012
I have added a new NME-WAE-502-K9 in one of our remote Cisco 2811 routers. This module doesn´t boot, and it seems to be in a loop trying to boot. [code]
View 6 Replies
View Related
Feb 6, 2012
I need Cisco router 2800 series boot ios image from network(tftp), when flash is corrupted or router doesn't see it, so it is impossible ? Command, i used boot system tftp: ios.bin but this does not work.
View 9 Replies
View Related
Dec 11, 2012
I purchased several 1921 routers and the last two I setup get the following error during bootup:
%SYS-6-READ_BOOTFILE_FAIL: tftp://255.255.255.255/1:aaa1386.bin No usable interfaces.
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
%MAINBOARD_GE-3-SHUTDOWN: FPA PKT pool holding 512 particles.boot of "1:aaa1386.
bin" using boot helper "usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" failed
error returned: No usable interfaces
loadprog: error - on file open
boot: cannot load "1:aaa1386.bin"
The router moves on and eventually comes up fine and is operational. What this error is an if I can get rid of it?
View 5 Replies
View Related
Dec 27, 2011
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
View 2 Replies
View Related
Feb 22, 2012
how to upgrade a Cisco Pix 525 boot rom from 4.0 to 4.3. Is it a physical chip or software upgrade? Is it needed to upgrade to latest IOS on Cisco Pix 525 to 8.0. Where can I find more information on it?
View 1 Replies
View Related
Jan 27, 2013
Whenever I try to open multiple sites, I will get a DNS lookup failure. Whenever I torrent something, websites give me a DNS lookup failure. Watch Youtube and open anoter site, DNS lookup failure. It seems that when I try to use too much internet I crash something... which doesn't make any sense because this problem has only come up recently. The only thing that I can think of is that I was messing around with the DNS to be able to connect to the American Netflix (I'm Canadian). I was using a site called "ZenOK" I believe, which gives you a server to connect to, and then a week later tells you it's no longer free (which they didn't mention in the signup)... so I removed the DNS number in my internet protocols, but I still get American Netflix.
View 14 Replies
View Related
Jan 1, 2013
I have a following question. I configured different authentication passwords in Master and slave VRRP setup.
View 2 Replies
View Related
Jul 12, 2011
we cant create EoX and PSIRT reports For Job-Log please see attached 1007.1.log.Patch lms40x-win-CSCto46927-0 has been installed already.CCO-Credentials + Proxy-settings in LMS must be oK, because we are able to auto download device packages for instance.
View 4 Replies
View Related
Nov 23, 2011
We have several unknown devices within our inventory. When running an inventory report the message I get back is "No Credentials available".
For inventory checks is it just SNMP that is used or is it the standard credentials that are needed ?
I am planning to edit the credentials for the single device manually to see if this makes a difference. Our integration is with ACS and we have a machine account with admin priveleges.
Device Verification for the device states "Device Not reachable" for SNMP and SSH. There are no drops on any of our firewalls but snmpwalk does work from the command prompt from the LMS server.
Are there any further checks I can make for these 2 messages:
* "No Credentials available". * "Device Not reachable"
View 2 Replies
View Related
