Cisco :: Can't Access WLC 5500 - Incomplete MAC
Mar 18, 2013
I have a 3750X set up with a number of VLANs and have connected a WLC5500 to this. I've assigned the port on the switch to the correct VLAN, given the WLC a management address on that VLAN and it has the correct gateway. I can ping to this gateway from other devices, but not from the WLC and can't ping or browse to the management address of the WLC (I can browse to it when plugged directly into the SP).
When checking the switch arp table, it shows the IP entry of the WLC as INCOMPLETE yet show cdp nei detail shows the device on the correct IP and all the device details. I have changed the port on the switch, the port on the WLC, the cable and the GBIC, cleared the arp and rebooted all devices and it hasn't made any difference. On the switch, I tried assigning the burned-in MAC to that IP statically but it didn't work - does each port have an individual MAC?
View 3 Replies
ADVERTISEMENT
Jun 4, 2013
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
View 11 Replies
View Related
May 11, 2011
I have a wave spot controller. That is connected to my PC(Fedora 14). In Shell I'm < arp -n > then I'm getting "Incomplete" in the place of Hardware Address.
View 1 Replies
View Related
Jun 20, 2011
providing the GPL sources for the DIR-615 rev.C firmware. However, it is incomplete!The bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link.
View 5 Replies
View Related
Dec 26, 2011
I plugged an IP device into a 2960 Catalyst switch. The port is up, but there is no MAC address learned on it:
TNSWAGCS01002(config-if)#do sh mac add int fa0/16
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
TNSWAGCS01002(config-if)#
TNSWAGCS01002(config-if)#do sh int fa0/16
FastEthernet0/16 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0064.40ee.f510 (bia 0064.40ee.f510)
Description: --- STC ---
[code]....
I read that it may be a L1/L2 issue. We tried with another ethernet cable. We also tried with another IP device of the same model. That did not solve the issue.
View 2 Replies
View Related
Sep 21, 2011
've used every version of ie up to 7 with no real problems, but I figured it had to be the browser, so I switched to Firefox. No improvement!Problems:When downloading (WinXP PC) online, suddenly all zips and apps (even Flash Player for browser) started showing "incomplete" or as it's called "Corrupt" files. One or two or maybe more small files would be left out. When finished downloading, it would say it completed the right mb's, but when unzipping or trying to install, there would be files missing. Tried "Repair" in WinRAR, no luck.
View 7 Replies
View Related
May 18, 2011
I recently purchased the Magnavox MBP5130/F7 Blue-Ray player. I have been trying to get the player to connect to my wireless network so that I can stream Netflix, etc. I am using a Linksys router. The device "sees" the wireless network (it displays the name) but I seem to get the error that the Wireless Router settings are incomplete - use advance settings to complete setup. In advance settings it fails - it is not possible to connect to the DNS server. Please confirm the internet connection or DNS address setting. IP Address 192.168.0.102;
View 14 Replies
View Related
Mar 23, 2013
I've just discovered that my wireless router is not secure (WRT54GS v5). In trying to set up the propoer security, the set up screen appears as incomplete (after entering 192.168.1.1). It only shows 3 tabs at the top - Basic Setup, MAC Address Clone, and Advanced Routing. No tab to deal with the settings. I have tried resetting the router and plug/unplug several times. Triued entering thru IE and Firefox.Is there another way to set up the security on my router or at least get the proper screen?
View 4 Replies
View Related
Sep 24, 2011
my researvation table is incomplete. Below I show ipconfig that shows wired & wireless NICs assigned ip addresses by the E3200 router but the DHCP table only shows one.
I need to reserve the ip address of the wired address but can't get at it.
View 2 Replies
View Related
Oct 20, 2012
is it possible to restrict the Remote Access VPN to ASA based on the Source Public IP , if so how ?
here I am not talking about the VPN-Filter under group-policy . I Want to restrict the access from specified source IP ( Public IP)
View 1 Replies
View Related
Jan 30, 2013
I have a Cisco aironet 3502i access point which I am using with a 5500 Wireless Controller. I was configuring the AP for flexconnect and accidentally enabled PPPoE authentication - but never set configured login details for PPPoE. Now when the AP boots up it tries to use PPPoE but fails - it never even looks for an IP address. I have no way to get the AP connected to the controller again.I tried logging into the AP via console, the AP gives me output but I never get a login, even when I hold down the Mode button during startup.I also tried holding the Mode button and waiting for the AP to boot with its default IP (10.0.0.1) and connecting to the AP via telnet, but I was unable to connect or even ping with my PC on the same network configured as 10.0.0.2.What can I do to set this AP back to defaults, to become a normal DHCP client, and reconnect to the wireless controller where I can reconfigure it?
View 9 Replies
View Related
Oct 11, 2012
I am having the peculiar issue in our ASA5500 firewall (version 8.2(5) ), where the remote access vpn is getting issue, I am unable to ping the internal resource for sometime, however without any modification the problem gets resolves.
During the issue we can see Tx count 0
Username : xxxxxx Index : 3147
Assigned IP : 172.17.254.24 Public IP : 14.99.x.x
Protocol : IKE IPsec
License : IPsec
Encryption : 3DES AES128 Hashing : SHA1
Bytes Tx : 0 Bytes Rx : 8764
Group Policy : EMP-VPN Tunnel Group : EMP-VPN
Login Time : 15:07:51 IST Fri Oct 12 2012
Duration : 0h:06m:34s
Inactivity : 0h:00m:00s
NAC Result : Unknown
VLAN Mapping : N/A VLAN : none
View 2 Replies
View Related
Aug 8, 2012
In the ISE documentation is states that under a Guest_Activity report you must have guest access logging enabled on the NAD in the ISE network. My question is where do I enable guest access logging in the WLC that is our NAD?
View 1 Replies
View Related
Feb 16, 2011
My web server sits behind an ASA 5500.When I access the web site from outside, it works fine. When I try and access it from the server itself, I get"Internet Explorer cannot display the webpage" error. I can access other web sites, such as Yahoo.com, Google.com, etc. I have rules setup to restrict/enable incoming traffic, but I don't have any rules setup to "loop back".
View 18 Replies
View Related
Jun 6, 2013
I am going to deploy Cisco ISE with WLC 5500. I have two kinds of users one for which I want to deploy just open access Wi-Fi network, without working with Cisco ISE and Second group of Users for which I want to deploy Cisco ISE services like advanced authentication, posture and profiling. For both users I have just one WLC. Is there any problem to just deploy two SSID one for open access (without Cisco ISE) and second Secure with Cisco ISE ?
View 5 Replies
View Related
Mar 9, 2011
administrator wants to manage ASA 5500 using inside interface.{telnet or ssh].Allowed telnet and ssh in ASA 5500 but unable to get access from administrator PC..Is there a way to do it without enabling NAT on the ASA? Will a specific rule on ASA allow adminstrator to access ASA 5500 inside interface via ssh or telnet?
View 2 Replies
View Related
May 20, 2012
I have a new WLC 5500 series which i upgraded to a newer version. We got brand new AP's 1242 from Cisco. My ex-colleague had said that we can pre-image the AP's using the controller, so the new AP's get the image directly from the Controllers.
I have the following devices with me for this: A WLC 5500, 1242 AP ( 12 No.'s) and a 2960 switch. I tried to create dhcp pool in wlc so the ap get the ip and gets the image . However, i cant see the ap appearing in wireless tab.
The WLC & AP will be connected to this same switch.
What configuration needs to be done on the WLC & the Switch so that the 1242 AP's when connected physically to the ports on the switch will get the image from the WLC.
View 7 Replies
View Related
Mar 5, 2013
I use the Service port connected to the managementVLAN to manage the WLCs. When configuring HA with AP SSO, I lost HTTPS connectivity to the WLC, telnet still works fine.I researched the deployment guide and it states:
- When AP SSO is enabled, there is no SNMP/GUI access on the service port for both the WLCs in the HA setup.Why is remote access disabled using GUI when using HA, and how can I keep management of my WLC using HTTPS and an address in the ManagementVLAN.
View 10 Replies
View Related
Oct 20, 2012
Is it possible to restrict the Remote Access VPN to ASA based on the Source Public IP , if so how ? here I am not talking about the VPN-Filter under group-policy . I Want to restrict the access from specified source IP (Public IP)
View 1 Replies
View Related
Oct 20, 2010
One of my Clients just aquired a CISCO ASA firewall, and they would like to restrict internet access, that is they want to block internet for Junior employees while managemnet remains connected, Looking at the situation, The ASA serves as the gateway,I tried an Access list like below for one pc to test if it works but instead everyone just went off, may be i misfired somehwere.
Access-list 110 deny tcp any host 192.168.20.100 eq wwwAccess-list 110 deny tcp any host 192.168.20.100 eq 443Access-list 110 permit tcp any any eq wwwAccess-list 110 permit tcp any any eq 443access-group 110 in interface inside
View 11 Replies
View Related
Nov 1, 2012
Got a bit of a quandary with joining new access points to our 5500 series W LAN Controller. It looks like the LAP is initially able to see the W LAN controller, but after that things go sideways. The LAP is pulling a valid IP address from DHCP, and the W LAN Controller is able to ping it.
In the controller's AP Join Statistics we get this:
Last AP Message Decryption Failure
Last AP Connection Failure -Timed out while waiting for ECHO repsonse from the AP
Last AP Disconnect Reason
[code]...
View 7 Replies
View Related
Jun 15, 2012
i have cisco CAP 3602e series access point to work with 5500 series controller with code 7.0i did not find VCI option 60 for this type of APs to configure DHCP. How I can let these APs will join the controller, i mean through which process DNS discovery methode and what about if i need to configure option 60 and 43 in dhcp for ap joining process to controllers.
View 4 Replies
View Related
Apr 30, 2012
We have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
View 2 Replies
View Related
Jan 23, 2012
How to successfully manage to configure ACS 5.1 to accept log in request from a 5500 WLC?
I've managed to get it configured following the follow link [URL], but when I try to log in to the WLC using my ACS credentials I just get the log in screen again. I've checked the ACS logs and it says my username has passed the authentication process and it matches all the rules I've set. The only thing I've noticed is my "Privilege Level" is only 1 but I'm not sure if thats correct for a HTTP log in.
View 21 Replies
View Related
Jun 5, 2011
We have a WLC 5500 apliance, but i have a problem, the APs have a administrative IP in a diferent segment, only conected to WLC the AP have same segment of the management interface, the 5500 don´t have APmanager interface.How configurate the WLC to conected and administrate all AP with different segment IP
Product Version.................................. 6.0.182.0
chasis: AIR-CT5508-K9
View 3 Replies
View Related
Jun 27, 2011
Due to lack of address space, I have to go to NAT for our wireless guest users.Are there any limitation with WLC/NGS when comes to NAT?I have four 5500 WLCs, should I put them in 1 mobility group, at 2 different locations?
View 1 Replies
View Related
May 3, 2011
We have a customer requirement of providing secure connectivity from Remote Office to HQSame time to provide certain level of layer 3 redundancy via secondary link should the primary link fail We are looking at ASA5500 series firewall for both Remote office and HQ.Can this be done?
View 3 Replies
View Related
May 30, 2012
We have a single 4404 that was setup long before I arrived with Guest networks that timeout and other such tweaks. Is there a document somewhere that shows a way to migrate the old settings to a new 5508 that we are purchasing? By the time the 5508 arrives I will have a very small window to setup the unit before a new wing goes live. I need the new unit as we have reached our limit of licensed AP's on the old 4404. It seems like everyone keeps talking about an easy way but no one says how to do it.
I have never setup one of these units before from scratch so I don't know how long it will take.
View 6 Replies
View Related
Feb 10, 2011
I have been trying to conect a Cisco VPN client through an ASA and it makes the connection but doesn't allow any traffic through. The ASA does have a site to site VPN attached to the outside interface.I suppose the first question is it possible to allow VPN client to connect through an ASA 5500 from the inside network when there are Site to Site VPN's already attached to the outside interfaces?If possible then what have I missed. I have tried adding NAT exempt for the traffic between the internal networks and "an IPSEC pass thru Inspect Map".
View 4 Replies
View Related
Nov 15, 2011
We have the ASA firewalls in our environment - two 5510's and one 5520.Our 5510's are currently used in our production environment and the 5520 is our firewall for pre-production and support personnel. My question is about the AnyConnect VPN licenses we have. Currently we have 100 seats for AnyConnect on our production ASA's, but we'd like to see if we can move half of these to the 5520 ASA?
View 1 Replies
View Related
Feb 8, 2011
i have a query regarding the no. of isakmp policy priority creating..when i create a new policy in ASA 5500 firewall, i get the below error...i assume it will support only 20 nos, where as we can use between 1-65535.. can anyone from cisco confirm it...running version is 8.x & VPN Plus license.Policy limit reached. No more than 20 isakmp policies can be configured.”
View 2 Replies
View Related
Aug 13, 2012
i have to open ports for vedio conferencing in my Firewall configuration ,
View 1 Replies
View Related
May 11, 2011
we are looking forward to monitoring the cpu, environment variables and the memory of a wireless lan controller via snmp. but we are not able to find in the mibs the right oid to manage this.can the exact oid be given in order to monitor these three elements on a cisco WLC 5500 series.
View 1 Replies
View Related
