we are looking forward to monitoring the cpu, environment variables and the memory of a wireless lan controller via snmp. but we are not able to find in the mibs the right oid to manage this.can the exact oid be given in order to monitor these three elements on a cisco WLC 5500 series.
View 1 RepliesI have an ASA 5500 Firewall. I need to figure out how to log all events using Port 25 to determine if there are any rogue devices on our network. I was trying to figure out how to do this via the Real-Time Monitoring (filter) but have had no success.
View 1 Replies View RelatedI have installed DCNM 6.2(1) on red hat 5.5 64bit and installed 4 evaluation (advanced) licenses on dcnm server:
DCNM-LAN-N3K-K9-EVAL
DCNM-LAN-N5K-K9-EVAL
DCNM-SAN-N5K-K9-EVAL
DCNM-SAN-M91-K9-EVAL
Licenses are activated on a total of 31 devices (nexus 5000 and 3000 series), data is being monitored, graphics are drawn. However under the Web user interface of DCNM, under Health, Virtual Port Channels (vPC) no data is shown. Performance, vPC is also empty. No vPC errors/notifications are displayed. The installed advanced-eval licenses should support all the bells and whistles (including vPC), but still- no monitoring is done about vPC-s. vPC-s are up and active. network is discovered and monitored via snmp v2c only. could this be limiting vPC discovery- needing snmpv3/ssh access?
is there a way in LMS 4.0 to generate a notification when a VPN tunnel drops on an ASA 5500?
View 1 Replies View RelatedWe are running LMS 3.2 with IPM 4.2 installed....and we are looking to do IPSLA monitoring on a couple of our Cisco ASR's with IOS-XE code installed.
I looked at the IPSLA feature mapping and it only talks about supported IOS code....do we need to upgrade our current IPM module to a current version?
if there is a MIB for monitoring temperature on a Cisco 800?
View 2 Replies View RelatedDoes any know why the ASA will monitor physical interfaces by default, but monitoring of logical interfaces is disabled by default? Or better yet, is anybody doing a monitor-interface for a subint without issue? I'd imagine it isn't enabled by default for a reason.
View 2 Replies View RelatedI have a question regarding netflow and NAT. I have read some documentation (on ASR1000) regarding monitoring NAT process on Cisco ASR1000 that can be done using netflow version 9 (the term was called netflow event logging a.k.a NEL). The problem is, I have not found the netflow collector that can do that. I have queried several software such as manage engine "Netflow Analyzer" and Lancope, but they said their software can not do that.
View 11 Replies View RelatedI am trying to setup VPN monitoring for a srp527w Cisco.This is my first attempt at this so "easy to understand" instructions would be a great, i have done some searching and its difficult to decipher relevant and irrelevant information based on my limited exposure to this technology.
View 1 Replies View RelatedVPN Tunnels Monitoring on ASA5510 with IOS 7.0 (Monitoring through Nagios Server).I want to use Nagios to monitor each of the S2S Tunnels built on ASA 5510. I can use the icmp on Nagios by adding Nagios host in IPSEC network of each tunnel but in that case the change needs to be done at other end of Tunnel as well.
View 2 Replies View RelatedI am proposing the Cisco Prime LMS 4.1 (i.e LMS-4.1-500-K9); Do I need to add the HUM license for monitoring or does that come inbuilt?
View 1 Replies View RelatedWe have around 20 VPN tunnel via Cisco Router 2821 (Intranet) and around 30 VPN tunnel via Cisco ASA (Internet) with 3rd Parties/Vendors.I wanna know if there is any monitoring tools from Cisco or any others providers who can give me information/trend report about VPN tunnel Up/Down time, Volumns of Traffic, Protocols etc.
View 2 Replies View RelatedIs there a way I can generate bandwidth reports on Cisco PIX 535 ?
View 1 Replies View RelatedOn the ASA5520 we would like to create a report that gives us trending over 6 monthes for the amount of people logged in via the SSL VPN and for how long. Is there a way to do this on the ASA5520? Does it have this ability? Could I do this in SolarWinds? My boss mentioned a software package that Cisco has that will show a history - is this correct?
View 1 Replies View RelatedHow to configure SLA monitoring in 3560 switch. I have 2 DSL links terminating in switch and want to do WAN failover. I know how to do in ASA and router. I found IP SLA and track commands on switch but don't know exactly how to use them.
View 2 Replies View RelatedHave a problem coming my way with regards monitoring 3g data usage on an 887 router. The router will carry two links - x1 primary over the serial port and x1 secondary failover link utilizing 3g.
The 3g sim has an allowance of 1Gb per month (traffic has been baselined and this seems sufficient - not by me though).I have a requirement to monitor the 3g link and trigger an alert at say the 60% mark (600Mb). Whatever mechanism is used to count the data also has to reset to 0 at the beginning of every month as data stats will be included in monthly reports.
Second conundrum, I also have to somehow split out the data usage stats to show my customers usage as well as my own. My own being management traffic (mainly snmp and icmp) and present this in the monthly report.
#1 - Does the 887 have some form of 3g accounting capability either via gui or cli that can fulfil my requirements above?
#2 - With splitting the data usage stats, could this be achieved using netflow and if it was possible, could i only have my flows sent down the Primary link (obviously only when it is active) and if the box fails to 3g have netflow just count the data until the Primary kicks in again.If no built in features can give me what i want i my go down the eem scripting route burt this is a last resort.
On LMS 3.2 there was a way to disable the monitoring of Device Interfaces.Examples are ISDN30 Channels, which go up and down during calls. I could disable the channel monitor on the relevant device and only monitor the Circuit as this is the main device to monitor.I can not find the same option in 4.2.2
View 2 Replies View Relatedhow to configure ip sla monitoring on asa ver 7.0 (6) ?
View 4 Replies View RelatedHow to confirm the PAT limit on the ACE-20s. I initially read it as 1 million (the NAT limit), however I have since read that for PAT, its 4 million as it uses the connection record information and not xlate.
I've always wondered why the xlate line under 'show resource usage' is zero. If PAT does use the connection record then this would explain why, however its confusing as when running a 'show xlate' command you do see all the current PAT entries.
LMS is not reporting on all of my interfaces, utilization in particular. As an example, I have 1 location that is connected via DMVPN tunnels, when I run a utilization report, it only comes back with information for 1 interface, a random interface, port FA 1/7 on the switch module. If it was all of the switchports it might make more sense.
In DFM device detail the interfaces are being managed.
In the Link Utilization Poller, only 1 interface is listed (FA 1/7).
We're currently running on ACS 5.2.0.26.9 with 2 appliances (one primary and one secondary).Today, I wanted to get some reports from the Monitoring and Reports tool. At beginning, it seemed impossible to generate them. Later, I decided to reload first primary and then secondary. As soon as I've done it, I got an email alert telling me that it failed parsing NAD.
Cisco Secure ACS - Alarm Notification
Severity: Critical
Alarm Name
System Alarm [Collector]
Cause/Trigger
[code]....
I don't really find where I can find the Collector log...Anyway now when I generate a 30 days report, I only get data up to 23.03.2012. Nothing recent !
We've had problems with our internet router losing connection to the internet. All traffic stops, a reboot resolves the problem. The router only has a public IP and it's connect through a dummy switch to the ASA as shown. I want to be able to monitor netflow or something and wondered if I could add a static route to the 10.x.x.x network and then add the netflow commands. Here is kind of how it looks, I simplified it some by removing unnecessary devices
View 2 Replies View RelatedI live in a shared flat. And all 20 rooms are connected to this switch I believe. Is there any method to prevent the landlord/tech guy monitoring our internet activity (e.g. bandwidith activity, websites we looked at, etc.
View 5 Replies View RelatedI need A network diagram for 50 PCs with Network monitoring
View 3 Replies View RelatedI have a questions about protecting my network. My parent's have rented out my room, since I'm going to college, and I was wondering if there was a way to monitor the traffic that is going on in my network. Once the guy moved in, the wireless connection speed drastically decreased. I was barely able to sure the internet on my laptop. I currently have about 8 devices connected to my network. I am running a wired connection for my desktop so I don't feel any lag, but everything else runs on wifi.
View 1 Replies View RelatedI was wondering if there is a way to monitor the total bandwidth available at any given time? My ISP claims and is charging me for a certain amount of bandwidth but I suspect that during the day I am getting much less.
I would like to track available bandwidth continuously (or every 5, 10, 15 minutes) and log that data so I can show them the results. I'm on a Mac 10.7 but can use Windows XP also.
We have a L3 core switch with multiple VLANs setup. Is there a way to place an IPS so as to monitor the traffic passing between, lets say, VLANS 1-3 and VLANs 4-10?
View 3 Replies View Related"how to monitoring VPN Login Session?" I want to the history of VPN User login to my VPN. How could I know?Which software can made me easy to monitoring and store those log in my SNMP Server? How to do that?
View 1 Replies View RelatedWe currently have a few 5505s installed at client sites which are connected via s2s ipsec VPN to our datacenter's 5510. We are using Nagios to monitor the local data center and remote client infrastructure (over the VPNs) which has been working well.
We would like to also monitor the remote 5505s using SNMP over the s2s tunnels but it doesn't seem to be working, the connection is timing out. We've configured the remote 5505s with the same snmp statement we used on the 5510 (snmp-server host inside <remote datacenter IP> poll community ***** version 2c) yet the Nagios SNMP check cannot connect to the remote 5505s. We've also tried the command using 'outside' without any luck, not sure how to get SNMP to route over the VPN.
I have a Cisco 2821 and ASA 5510 as a VPN Router in my network.Our remote users are using Cisco VPN Client 5.0.07 and I need to monitor them on a server and keep their Connection Info to generate some reports for my manager.
View 1 Replies View RelatedI want to setup BB to monitor snmptraps with failure. The BB log shows can't connect to all switch ports 161, and I even can't telnet to XXX_17f 161 for example. My switches are Cisco C3550, C2950, ASA etc.
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX_17f on port 161
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX_9f on port 161
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX on port 161
how can I monitor and prioritise traffic on a ASR 1002? Currently we have allowed another organization to use our 1GB link and we would like to monitor what sort of traffic flows through it and want to prioritise the traffic depending on the applications.
View 1 Replies View RelatedI am trying to poll the 5 minute average CPU utilization of my Cisco Aironet 1252 (IOS version 12.4(25d)JA) using SNMP OID .1.3.6.1.4.1.9.2.1.58.0.However for some reason I am not getting any response back from the aironet. Note I am able to retrive the memory utilization without a problem.
View 1 Replies View Related