On LMS 3.2 there was a way to disable the monitoring of Device Interfaces.Examples are ISDN30 Channels, which go up and down during calls. I could disable the channel monitor on the relevant device and only monitor the Circuit as this is the main device to monitor.I can not find the same option in 4.2.2
View 2 RepliesWhat are considered the best practices for monitoring ASA's--specifically the 5510 with Sec+ License.
My current monitoring application keeps reporting issues with outbound interface buffers being too high, but there are not any performance issues and I believe the thresholds are just set absurdly low.
LMS is not reporting on all of my interfaces, utilization in particular. As an example, I have 1 location that is connected via DMVPN tunnels, when I run a utilization report, it only comes back with information for 1 interface, a random interface, port FA 1/7 on the switch module. If it was all of the switchports it might make more sense.
In DFM device detail the interfaces are being managed.
In the Link Utilization Poller, only 1 interface is listed (FA 1/7).
I have a Cisco 1184 with Hwic 1-t (IOS 12.4(15)T12 ). i want monitoring average load of my HDSL. How to can i monitoring my bandwith in upload and in download for WAN interface ?
View 3 Replies View RelatedI'm trying to get started on setting up my first Transparent ASA.I understand an ASA in Transparent Mode can now have an ip address with Bridge Groups or some such mechanism. I'm looking for examples of how to set that up and other information below. Is the ip address associated with the device or is it interface specific? Will I be able to SSH with that ip address setup? Can I use ASDM if the Transparent ASA has an ip address? This 5512X has an IPS. Any one who has setup an IPS on this platform knows it has some very particular requirments in order to communicate with the outside world. I need examples of how to do that with a Transparent ASA.How is NAT setup differently (if at all) on a Transparent ASA?Are ACLs done any differently?
View 3 Replies View Relatedhow to configure vlan tag on routed layer 3 interface in cisco 3945 device?
View 2 Replies View RelatedWe are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedMy BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies View RelatedThe problem: I need to track a bus from city to city in real time.I'm thinking of a gps device without screen or apps, it only sends the current location to a server. Is this possible? What device can be useful?
View 1 Replies View RelatedI have installed DCNM 6.2(1) on red hat 5.5 64bit and installed 4 evaluation (advanced) licenses on dcnm server:
DCNM-LAN-N3K-K9-EVAL
DCNM-LAN-N5K-K9-EVAL
DCNM-SAN-N5K-K9-EVAL
DCNM-SAN-M91-K9-EVAL
Licenses are activated on a total of 31 devices (nexus 5000 and 3000 series), data is being monitored, graphics are drawn. However under the Web user interface of DCNM, under Health, Virtual Port Channels (vPC) no data is shown. Performance, vPC is also empty. No vPC errors/notifications are displayed. The installed advanced-eval licenses should support all the bells and whistles (including vPC), but still- no monitoring is done about vPC-s. vPC-s are up and active. network is discovered and monitored via snmp v2c only. could this be limiting vPC discovery- needing snmpv3/ssh access?
is there a way in LMS 4.0 to generate a notification when a VPN tunnel drops on an ASA 5500?
View 1 Replies View RelatedWe are running LMS 3.2 with IPM 4.2 installed....and we are looking to do IPSLA monitoring on a couple of our Cisco ASR's with IOS-XE code installed.
I looked at the IPSLA feature mapping and it only talks about supported IOS code....do we need to upgrade our current IPM module to a current version?
if there is a MIB for monitoring temperature on a Cisco 800?
View 2 Replies View Relatedi have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View RelatedI have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
Does any know why the ASA will monitor physical interfaces by default, but monitoring of logical interfaces is disabled by default? Or better yet, is anybody doing a monitor-interface for a subint without issue? I'd imagine it isn't enabled by default for a reason.
View 2 Replies View RelatedI have a question regarding netflow and NAT. I have read some documentation (on ASR1000) regarding monitoring NAT process on Cisco ASR1000 that can be done using netflow version 9 (the term was called netflow event logging a.k.a NEL). The problem is, I have not found the netflow collector that can do that. I have queried several software such as manage engine "Netflow Analyzer" and Lancope, but they said their software can not do that.
View 11 Replies View RelatedI am trying to setup VPN monitoring for a srp527w Cisco.This is my first attempt at this so "easy to understand" instructions would be a great, i have done some searching and its difficult to decipher relevant and irrelevant information based on my limited exposure to this technology.
View 1 Replies View RelatedVPN Tunnels Monitoring on ASA5510 with IOS 7.0 (Monitoring through Nagios Server).I want to use Nagios to monitor each of the S2S Tunnels built on ASA 5510. I can use the icmp on Nagios by adding Nagios host in IPSEC network of each tunnel but in that case the change needs to be done at other end of Tunnel as well.
View 2 Replies View RelatedI am proposing the Cisco Prime LMS 4.1 (i.e LMS-4.1-500-K9); Do I need to add the HUM license for monitoring or does that come inbuilt?
View 1 Replies View RelatedWe have around 20 VPN tunnel via Cisco Router 2821 (Intranet) and around 30 VPN tunnel via Cisco ASA (Internet) with 3rd Parties/Vendors.I wanna know if there is any monitoring tools from Cisco or any others providers who can give me information/trend report about VPN tunnel Up/Down time, Volumns of Traffic, Protocols etc.
View 2 Replies View RelatedIs there a way I can generate bandwidth reports on Cisco PIX 535 ?
View 1 Replies View Relatedwe are looking forward to monitoring the cpu, environment variables and the memory of a wireless lan controller via snmp. but we are not able to find in the mibs the right oid to manage this.can the exact oid be given in order to monitor these three elements on a cisco WLC 5500 series.
View 1 Replies View RelatedOn the ASA5520 we would like to create a report that gives us trending over 6 monthes for the amount of people logged in via the SSL VPN and for how long. Is there a way to do this on the ASA5520? Does it have this ability? Could I do this in SolarWinds? My boss mentioned a software package that Cisco has that will show a history - is this correct?
View 1 Replies View RelatedHow to configure SLA monitoring in 3560 switch. I have 2 DSL links terminating in switch and want to do WAN failover. I know how to do in ASA and router. I found IP SLA and track commands on switch but don't know exactly how to use them.
View 2 Replies View RelatedHave a problem coming my way with regards monitoring 3g data usage on an 887 router. The router will carry two links - x1 primary over the serial port and x1 secondary failover link utilizing 3g.
The 3g sim has an allowance of 1Gb per month (traffic has been baselined and this seems sufficient - not by me though).I have a requirement to monitor the 3g link and trigger an alert at say the 60% mark (600Mb). Whatever mechanism is used to count the data also has to reset to 0 at the beginning of every month as data stats will be included in monthly reports.
Second conundrum, I also have to somehow split out the data usage stats to show my customers usage as well as my own. My own being management traffic (mainly snmp and icmp) and present this in the monthly report.
#1 - Does the 887 have some form of 3g accounting capability either via gui or cli that can fulfil my requirements above?
#2 - With splitting the data usage stats, could this be achieved using netflow and if it was possible, could i only have my flows sent down the Primary link (obviously only when it is active) and if the box fails to 3g have netflow just count the data until the Primary kicks in again.If no built in features can give me what i want i my go down the eem scripting route burt this is a last resort.
how to configure ip sla monitoring on asa ver 7.0 (6) ?
View 4 Replies View RelatedHow to confirm the PAT limit on the ACE-20s. I initially read it as 1 million (the NAT limit), however I have since read that for PAT, its 4 million as it uses the connection record information and not xlate.
I've always wondered why the xlate line under 'show resource usage' is zero. If PAT does use the connection record then this would explain why, however its confusing as when running a 'show xlate' command you do see all the current PAT entries.
We're currently running on ACS 5.2.0.26.9 with 2 appliances (one primary and one secondary).Today, I wanted to get some reports from the Monitoring and Reports tool. At beginning, it seemed impossible to generate them. Later, I decided to reload first primary and then secondary. As soon as I've done it, I got an email alert telling me that it failed parsing NAD.
Cisco Secure ACS - Alarm Notification
Severity: Critical
Alarm Name
System Alarm [Collector]
Cause/Trigger
[code]....
I don't really find where I can find the Collector log...Anyway now when I generate a 30 days report, I only get data up to 23.03.2012. Nothing recent !
Is it possible to set up a WAN interface on a FastEthernet interface of a Cisco 877 Adsl Router ?Due to my ISP, i've to use an external VDSL modem and must connect it to my cisco 877 router (and leave it's adsl interface unused).But i don't know how to set up a wan port, other than the adsl interface itself (dialer0), on my cisco.
View 7 Replies View RelatedWe are having Cisco ASA 5540 having Cisco Adaptive Security Appliance Software Version 8.0(5)23 at certain time of moment daily wer are facing latency and packetdrop wherin when I checked for ASA Interface which gives me " Input Errors" on outside interface ,so can any one tell me what are the causes to get input errors on cisco asa outisde interface.
View 2 Replies View RelatedWe've had problems with our internet router losing connection to the internet. All traffic stops, a reboot resolves the problem. The router only has a public IP and it's connect through a dummy switch to the ASA as shown. I want to be able to monitor netflow or something and wondered if I could add a static route to the 10.x.x.x network and then add the netflow commands. Here is kind of how it looks, I simplified it some by removing unnecessary devices
View 2 Replies View RelatedI live in a shared flat. And all 20 rooms are connected to this switch I believe. Is there any method to prevent the landlord/tech guy monitoring our internet activity (e.g. bandwidith activity, websites we looked at, etc.
View 5 Replies View Related