Cisco :: LMS 4.0 Interface Utilization / Monitoring?
Jul 18, 2011
LMS is not reporting on all of my interfaces, utilization in particular. As an example, I have 1 location that is connected via DMVPN tunnels, when I run a utilization report, it only comes back with information for 1 interface, a random interface, port FA 1/7 on the switch module. If it was all of the switchports it might make more sense.
In DFM device detail the interfaces are being managed.
In the Link Utilization Poller, only 1 interface is listed (FA 1/7).
View 2 Replies
ADVERTISEMENT
Sep 8, 2011
We have a Cisco ASA 5520 supporting multiple VPNs - both remote-access and Lan-to-Lan. We would like to monitor the bandwidth utilization of the IPSec Lan-to-Lan tunnels.
View 3 Replies
View Related
Sep 17, 2012
On LMS 3.2 there was a way to disable the monitoring of Device Interfaces.Examples are ISDN30 Channels, which go up and down during calls. I could disable the channel monitor on the relevant device and only monitor the Circuit as this is the main device to monitor.I can not find the same option in 4.2.2
View 2 Replies
View Related
Dec 8, 2010
I have a Cisco 1184 with Hwic 1-t (IOS 12.4(15)T12 ). i want monitoring average load of my HDSL. How to can i monitoring my bandwith in upload and in download for WAN interface ?
View 3 Replies
View Related
Mar 2, 2013
Interface Utilization report displays the interface utilization data for each device polled for the Interface Utilization template. The information is presented using the percentage specifier.
For eg its displayed % (Rx Max%,Rx Avg%,RxMin%,
Tx Max%,Tx Avg%,TxMin%)
I wants report should have the data(interface utilization In Bytes of data)Can we display the data instead of the percentage?
View 0 Replies
View Related
Jan 13, 2013
I have a cisco 1841, Im trying to write an app which will get the Interface Utilization on my 2 atm interfaces and fast eth 0/0 interface.
I’ve been reading up and have got as far as downloading the codeplex snmp library project. I’m using the snmpget app to get details off my 1841 successfully, but I now need to know the OID for interface utilization and how to define which interface to get.
View 1 Replies
View Related
Jun 24, 2012
I have one question regarding switch sg300-10. How can i check current interface utilization in bits/second? If I use show int counters I can only see number of unicast, broadcast and multicast packets....plus total packets. But there is no info regarding input and output rate for particular interface (like in original IOS when using show interface command).
View 3 Replies
View Related
Oct 30, 2011
I have a problem with System-defined Link Port Interface Utilization Poller. When I generate Interface Utilization Report, this one just displays few Interfaces (see the figure in my attachment). I checked the default poller for interface utilization and recognize that it just associate with few Interface (same as in Interface Utilization Report) instead all. I need to display the utilization of all interfaces in my report
Is Link Port Interface Utilization wrong or Is it necessary to creat user-defined poller that associate with all interfaces of devices?
View 1 Replies
View Related
Aug 3, 2011
I'm using a stack of four SGE2000P switches for a PoE video camera system. I've got the cameras in a VLAN and everything's working fine.
I'm wondering, though, is there a way to find out what data rate the stack interfaces are working at (since it's going over cable infrastructure we put in ourselves), and also what percentage of that bandwidth is being used? I don't see anyway to get to those interfaces from the main page, and I wasn't able to find a way to do any sort of percentage thing even on a regular interface.
View 2 Replies
View Related
Dec 19, 2011
The other day 3rd party supplier ran some stats on our Gigabit link between 2 Cisco catalyst 3750Gs.now the graphs produced showed only a Maximum output of about 100Mbps ( 5 minute intervals) yet when I do a show interface it shows a lot more always 150Mbps and more. So I did my own Perl script doing an "sh interface" every minute and then graphed it, and the results were a lot different to the MRTG results.Questions: I know MRTG uses SNMP to get the traffic is there a bug in the SNMP, what OID does it use?does the "sh interface" give the correct results?
View 2 Replies
View Related
May 19, 2013
i noticed the "output drops" increasing in interface gi 1/0/1 in my switch 2960-S although the utilization of my interface is between 20% and 50 %
SW__A#sh interfaces gigabitEthernet 1/0/1
GigabitEthernet1/0/1 is up, line protocol is up (connected)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 93/255, rxload 3/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
[code]....
what is the cause of this issue ?
View 20 Replies
View Related
May 12, 2013
I have installed DCNM 6.2(1) on red hat 5.5 64bit and installed 4 evaluation (advanced) licenses on dcnm server:
DCNM-LAN-N3K-K9-EVAL
DCNM-LAN-N5K-K9-EVAL
DCNM-SAN-N5K-K9-EVAL
DCNM-SAN-M91-K9-EVAL
Licenses are activated on a total of 31 devices (nexus 5000 and 3000 series), data is being monitored, graphics are drawn. However under the Web user interface of DCNM, under Health, Virtual Port Channels (vPC) no data is shown. Performance, vPC is also empty. No vPC errors/notifications are displayed. The installed advanced-eval licenses should support all the bells and whistles (including vPC), but still- no monitoring is done about vPC-s. vPC-s are up and active. network is discovered and monitored via snmp v2c only. could this be limiting vPC discovery- needing snmpv3/ssh access?
View 1 Replies
View Related
Apr 11, 2011
is there a way in LMS 4.0 to generate a notification when a VPN tunnel drops on an ASA 5500?
View 1 Replies
View Related
Oct 26, 2011
We are running LMS 3.2 with IPM 4.2 installed....and we are looking to do IPSLA monitoring on a couple of our Cisco ASR's with IOS-XE code installed.
I looked at the IPSLA feature mapping and it only talks about supported IOS code....do we need to upgrade our current IPM module to a current version?
View 0 Replies
View Related
Sep 17, 2012
if there is a MIB for monitoring temperature on a Cisco 800?
View 2 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
May 12, 2011
Does any know why the ASA will monitor physical interfaces by default, but monitoring of logical interfaces is disabled by default? Or better yet, is anybody doing a monitor-interface for a subint without issue? I'd imagine it isn't enabled by default for a reason.
View 2 Replies
View Related
Feb 7, 2010
I have a question regarding netflow and NAT. I have read some documentation (on ASR1000) regarding monitoring NAT process on Cisco ASR1000 that can be done using netflow version 9 (the term was called netflow event logging a.k.a NEL). The problem is, I have not found the netflow collector that can do that. I have queried several software such as manage engine "Netflow Analyzer" and Lancope, but they said their software can not do that.
View 11 Replies
View Related
Feb 9, 2012
I am trying to setup VPN monitoring for a srp527w Cisco.This is my first attempt at this so "easy to understand" instructions would be a great, i have done some searching and its difficult to decipher relevant and irrelevant information based on my limited exposure to this technology.
View 1 Replies
View Related
Jul 8, 2012
VPN Tunnels Monitoring on ASA5510 with IOS 7.0 (Monitoring through Nagios Server).I want to use Nagios to monitor each of the S2S Tunnels built on ASA 5510. I can use the icmp on Nagios by adding Nagios host in IPSEC network of each tunnel but in that case the change needs to be done at other end of Tunnel as well.
View 2 Replies
View Related
Jan 16, 2012
I am proposing the Cisco Prime LMS 4.1 (i.e LMS-4.1-500-K9); Do I need to add the HUM license for monitoring or does that come inbuilt?
View 1 Replies
View Related
Nov 7, 2010
We have around 20 VPN tunnel via Cisco Router 2821 (Intranet) and around 30 VPN tunnel via Cisco ASA (Internet) with 3rd Parties/Vendors.I wanna know if there is any monitoring tools from Cisco or any others providers who can give me information/trend report about VPN tunnel Up/Down time, Volumns of Traffic, Protocols etc.
View 2 Replies
View Related
Sep 25, 2011
Is there a way I can generate bandwidth reports on Cisco PIX 535 ?
View 1 Replies
View Related
May 11, 2011
we are looking forward to monitoring the cpu, environment variables and the memory of a wireless lan controller via snmp. but we are not able to find in the mibs the right oid to manage this.can the exact oid be given in order to monitor these three elements on a cisco WLC 5500 series.
View 1 Replies
View Related
Sep 12, 2012
On the ASA5520 we would like to create a report that gives us trending over 6 monthes for the amount of people logged in via the SSL VPN and for how long. Is there a way to do this on the ASA5520? Does it have this ability? Could I do this in SolarWinds? My boss mentioned a software package that Cisco has that will show a history - is this correct?
View 1 Replies
View Related
Jun 26, 2011
How to configure SLA monitoring in 3560 switch. I have 2 DSL links terminating in switch and want to do WAN failover. I know how to do in ASA and router. I found IP SLA and track commands on switch but don't know exactly how to use them.
View 2 Replies
View Related
Oct 28, 2012
Have a problem coming my way with regards monitoring 3g data usage on an 887 router. The router will carry two links - x1 primary over the serial port and x1 secondary failover link utilizing 3g.
The 3g sim has an allowance of 1Gb per month (traffic has been baselined and this seems sufficient - not by me though).I have a requirement to monitor the 3g link and trigger an alert at say the 60% mark (600Mb). Whatever mechanism is used to count the data also has to reset to 0 at the beginning of every month as data stats will be included in monthly reports.
Second conundrum, I also have to somehow split out the data usage stats to show my customers usage as well as my own. My own being management traffic (mainly snmp and icmp) and present this in the monthly report.
#1 - Does the 887 have some form of 3g accounting capability either via gui or cli that can fulfil my requirements above?
#2 - With splitting the data usage stats, could this be achieved using netflow and if it was possible, could i only have my flows sent down the Primary link (obviously only when it is active) and if the box fails to 3g have netflow just count the data until the Primary kicks in again.If no built in features can give me what i want i my go down the eem scripting route burt this is a last resort.
View 2 Replies
View Related
Dec 20, 2011
how to configure ip sla monitoring on asa ver 7.0 (6) ?
View 4 Replies
View Related
Dec 14, 2011
How to confirm the PAT limit on the ACE-20s. I initially read it as 1 million (the NAT limit), however I have since read that for PAT, its 4 million as it uses the connection record information and not xlate.
I've always wondered why the xlate line under 'show resource usage' is zero. If PAT does use the connection record then this would explain why, however its confusing as when running a 'show xlate' command you do see all the current PAT entries.
View 5 Replies
View Related
Apr 3, 2012
We're currently running on ACS 5.2.0.26.9 with 2 appliances (one primary and one secondary).Today, I wanted to get some reports from the Monitoring and Reports tool. At beginning, it seemed impossible to generate them. Later, I decided to reload first primary and then secondary. As soon as I've done it, I got an email alert telling me that it failed parsing NAD.
Cisco Secure ACS - Alarm Notification
Severity: Critical
Alarm Name
System Alarm [Collector]
Cause/Trigger
[code]....
I don't really find where I can find the Collector log...Anyway now when I generate a 30 days report, I only get data up to 23.03.2012. Nothing recent !
View 7 Replies
View Related
Apr 9, 2011
Is it possible to set up a WAN interface on a FastEthernet interface of a Cisco 877 Adsl Router ?Due to my ISP, i've to use an external VDSL modem and must connect it to my cisco 877 router (and leave it's adsl interface unused).But i don't know how to set up a wan port, other than the adsl interface itself (dialer0), on my cisco.
View 7 Replies
View Related
May 28, 2013
We are having Cisco ASA 5540 having Cisco Adaptive Security Appliance Software Version 8.0(5)23 at certain time of moment daily wer are facing latency and packetdrop wherin when I checked for ASA Interface which gives me " Input Errors" on outside interface ,so can any one tell me what are the causes to get input errors on cisco asa outisde interface.
View 2 Replies
View Related
