Cisco Wireless :: 5500 - Image Loading On Access Point?
May 20, 2012
I have a new WLC 5500 series which i upgraded to a newer version. We got brand new AP's 1242 from Cisco. My ex-colleague had said that we can pre-image the AP's using the controller, so the new AP's get the image directly from the Controllers.
I have the following devices with me for this: A WLC 5500, 1242 AP ( 12 No.'s) and a 2960 switch. I tried to create dhcp pool in wlc so the ap get the ip and gets the image . However, i cant see the ap appearing in wireless tab.
The WLC & AP will be connected to this same switch.
What configuration needs to be done on the WLC & the Switch so that the 1242 AP's when connected physically to the ports on the switch will get the image from the WLC.
View 7 Replies
ADVERTISEMENT
Jun 4, 2013
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.
View 11 Replies
View Related
Jan 28, 2013
I've looked through the documentation for loading the autonomous image on a 1552E WAP that has the lightweight image on it. All the documentation I can find mentions using the "archive" command at the command line. It doesn't appear to like the archive command.
I've seen in the documentation that it also mentions the software is loadable through the controller, but I can't figure out how to do that.
I currently have the 1552E connected to my 5508 controllers running 7.3 software. how to load this autonomous image on to the 1552E? I'm planning on using it to do site surveys with the 1552E.
View 7 Replies
View Related
Jul 25, 2011
i just bought a 5508 wireless controller that was delivered yesterday .I powered it on yesterday and was able to make basic configurations of management interface ,time and zone settings.I was also able to get to the GUi and console after the configs and it was alright. When I got in this morning it ran for about 2 hours and all of a sudden starts shutting down after every % minutes and comes back again.
View 7 Replies
View Related
Sep 18, 2011
I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is 7.0.116.0 (default) 7.0.98.218 (active) so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its 7.0.116.0 (default)(active) 7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting.
View 1 Replies
View Related
Jun 15, 2012
i have cisco CAP 3602e series access point to work with 5500 series controller with code 7.0i did not find VCI option 60 for this type of APs to configure DHCP. How I can let these APs will join the controller, i mean through which process DNS discovery methode and what about if i need to configure option 60 and 43 in dhcp for ap joining process to controllers.
View 4 Replies
View Related
Apr 30, 2012
We have recently been given this unusual task. The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition. Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?
View 2 Replies
View Related
Oct 23, 2012
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
View 1 Replies
View Related
Aug 23, 2011
I've a problem with a router 2811:
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
[Code]......
View 14 Replies
View Related
Sep 13, 2011
download an autonomous image for Cisco Access point 1242 ?
View 1 Replies
View Related
Jun 9, 2013
how to replace an image in webauth-bundle on WLC 5500?When I run "show custom-web webauth-bundle", I do see the files:
aup.html
login.html
yourlogo.jpg
But, the size of yourlogo.jpg is too big and need to replace with a smaller one.I have tried (with the appropiate IP and filename):
transfer download mode tftp
transfer download datatype image
transfer download serverip tftp-server-ip-addres
transfer download filename {filename.jpg | filename.gif | filename.png}
but, it does not work.
View 5 Replies
View Related
Jun 22, 2012
I have 5500 controller with firmware 7.0 installed from the factory. Due to some reasons, I understood that other existing wireless infrastructure runs on firmware 6.0, and hance i need to downgrade the 5500 series to 6.0 . During the bootup, i could see there is another image called backup recovery image, which is running on version 6.0. How can i reboot controller to use the older image , which is from backup recovery image. I couldnt find it in the configuration guide.
View 4 Replies
View Related
Apr 3, 2012
We are now using image 8.0(4) for my ASA 5510. Later on, I would like to upgrade the image to 8.4(3).May I have to know what difference for those images, what should I take care of the script?
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
May 22, 2012
I have a WRT54G with updated firmware. Today I saved my configuration to a config.bin file. When I tried loading the file, the admin screen went blank. Now I am no longer able to access either the internet or the router's admin page. Is a hard reset my only option?
View 6 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jan 30, 2013
I have a Cisco aironet 3502i access point which I am using with a 5500 Wireless Controller. I was configuring the AP for flexconnect and accidentally enabled PPPoE authentication - but never set configured login details for PPPoE. Now when the AP boots up it tries to use PPPoE but fails - it never even looks for an IP address. I have no way to get the AP connected to the controller again.I tried logging into the AP via console, the AP gives me output but I never get a login, even when I hold down the Mode button during startup.I also tried holding the Mode button and waiting for the AP to boot with its default IP (10.0.0.1) and connecting to the AP via telnet, but I was unable to connect or even ping with my PC on the same network configured as 10.0.0.2.What can I do to set this AP back to defaults, to become a normal DHCP client, and reconnect to the wireless controller where I can reconfigure it?
View 9 Replies
View Related
Aug 8, 2012
In the ISE documentation is states that under a Guest_Activity report you must have guest access logging enabled on the NAD in the ISE network. My question is where do I enable guest access logging in the WLC that is our NAD?
View 1 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Mar 5, 2013
I use the Service port connected to the managementVLAN to manage the WLCs. When configuring HA with AP SSO, I lost HTTPS connectivity to the WLC, telnet still works fine.I researched the deployment guide and it states:
- When AP SSO is enabled, there is no SNMP/GUI access on the service port for both the WLCs in the HA setup.Why is remote access disabled using GUI when using HA, and how can I keep management of my WLC using HTTPS and an address in the ManagementVLAN.
View 10 Replies
View Related
Sep 22, 2012
I'm trying to upload a new software image (~86mb) from my PC to the WiSM2 controller on a 6513 chassis.
Midway through the transfer, the transfer stopped and I got this error on the log:
*TransferTask: Jan 01 00:28:33.124: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4508 Error FTP file Transfer [ftp_get], <28>, No space left on device.
How to access the memory on the wism to delete the old boot image?
View 1 Replies
View Related
Nov 1, 2012
Got a bit of a quandary with joining new access points to our 5500 series W LAN Controller. It looks like the LAP is initially able to see the W LAN controller, but after that things go sideways. The LAP is pulling a valid IP address from DHCP, and the W LAN Controller is able to ping it.
In the controller's AP Join Statistics we get this:
Last AP Message Decryption Failure
Last AP Connection Failure -Timed out while waiting for ECHO repsonse from the AP
Last AP Disconnect Reason
[code]...
View 7 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
Apr 6, 2011
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies
View Related
