Cisco Wireless :: 5500 How To Reboot Controller To Use Backup Recovery Image
Jun 22, 2012
I have 5500 controller with firmware 7.0 installed from the factory. Due to some reasons, I understood that other existing wireless infrastructure runs on firmware 6.0, and hance i need to downgrade the 5500 series to 6.0 . During the bootup, i could see there is another image called backup recovery image, which is running on version 6.0. How can i reboot controller to use the older image , which is from backup recovery image. I couldnt find it in the configuration guide.
View 4 Replies
ADVERTISEMENT
Oct 23, 2012
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
View 1 Replies
View Related
Mar 18, 2012
I have an Aironet 1231G that I'm trying to recover an image on. I'm following the cisco directions of reloading the AP image file from an active TFTP server (which is myPC). My PC has a static ip address of 10.0.0.2 with the TFTP server running. I've verfied that the TFTP server works by upgrading a switch IOS.The issue I'm encountering is the 1231G does not see the TFTP server correctly. url...
View 2 Replies
View Related
Mar 31, 2013
We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies
View Related
May 20, 2012
I have a new WLC 5500 series which i upgraded to a newer version. We got brand new AP's 1242 from Cisco. My ex-colleague had said that we can pre-image the AP's using the controller, so the new AP's get the image directly from the Controllers.
I have the following devices with me for this: A WLC 5500, 1242 AP ( 12 No.'s) and a 2960 switch. I tried to create dhcp pool in wlc so the ap get the ip and gets the image . However, i cant see the ap appearing in wireless tab.
The WLC & AP will be connected to this same switch.
What configuration needs to be done on the WLC & the Switch so that the 1242 AP's when connected physically to the ports on the switch will get the image from the WLC.
View 7 Replies
View Related
Jun 9, 2013
how to replace an image in webauth-bundle on WLC 5500?When I run "show custom-web webauth-bundle", I do see the files:
aup.html
login.html
yourlogo.jpg
But, the size of yourlogo.jpg is too big and need to replace with a smaller one.I have tried (with the appropiate IP and filename):
transfer download mode tftp
transfer download datatype image
transfer download serverip tftp-server-ip-addres
transfer download filename {filename.jpg | filename.gif | filename.png}
but, it does not work.
View 5 Replies
View Related
Jul 20, 2008
how to password recovery Wireless LAN Controller 4402
View 3 Replies
View Related
Jun 3, 2012
The customer forgot the password for the ASA SSM-20 ips module installed in ASA 5520 Fw.show module in customer FW shows it up state. I brought it to our office teat bed. here it show
ASA1# sh module
Mod Card Type Model Serial No.
--- -------------------------------------------- ------------------ -----------
0 ASA 5520 Adaptive Security Appliance ASA5520-K8 JMX1022K03A
1 ASA 5500 Series Security Services Module-20 ASA-SSM-20 JAB101003C2
Mod MAC Address Range Hw Version Fw Version Sw Version
[code]....*-
what to do with this module in my test bed.I have to take it back to the customer site to use it in their ASA itself to troubleshoot.There it the status is up and i did use all the hw-module option but no use. The version is 5.0. This module is more than 5 years old and so far no one upgrade the image. ASA 5520 running 8.2.5.
View 8 Replies
View Related
Apr 3, 2012
We are now using image 8.0(4) for my ASA 5510. Later on, I would like to upgrade the image to 8.4(3).May I have to know what difference for those images, what should I take care of the script?
View 1 Replies
View Related
Oct 31, 2011
Before nearly four years we have purchased 4 Cisco ASA 5500 Device for our organization.Out of these four device currently two are active in field and other two we kept as a spare.Now, in one active device we are facing very rare and strange issue.
The device automatically soft reboot once in nearly 60 days and we do not have any pre or post symptoms of this incident only server logs providing us this information.The device itself located in very controlled environment in a data center where physical tampering or temperature waviness is not possible.
We also asked one Cisco Expert from data center but still issue is not solved.Before two month, using remote syslog service we also started log redirection to a server so that when such incident occurs we have something to analyze but it is worthless log has nothing to tell us.
My questions are
1. "It is a hardware fault or software issue?"
2. "Is it possible with Cisco 5500 that automatically it reboots due to some internal hardware/software issue, if yes how we can trap or monitor it?
[code]...
View 3 Replies
View Related
Aug 27, 2011
I have two 5500-controllers and one WCS-server. Now I will have to move the WCS-server to another subnet and change the IP, but it will keep the name.Will that effect the connection between the controllers and the WCS?Do I have the change anything in the configuration on the controllers or the WCS-server?
View 3 Replies
View Related
May 27, 2012
I am working on a project that will involve 5500 controllers managing 1260 series N rate A/Ps. There may be a requirement for MESH but my previous experience using Motorola 802.11a radios is that random, intermittent radio detections resulted in the MESH network having to keep re-forming resulting in less than 100% availability.
What's peoples experience in the UK is 802.11a outdoors?
Ideally i would prefer to use 2.4GHz and repeater access points for those areas not serviced with data connection but I cant find any info' so far on how whether the 5500 controller is able to manage repeater access points.
View 2 Replies
View Related
Jul 2, 2012
While configuring a 5500 wireless controller, i came across this option of DHCP proxy under Advanced tab of Controller Option.It asks for the dhcp option 82 remote id format & the dhcp timeout.
1. What is the significance of this & when do we use it?
2. Also, under each wlan ssid that we create, there is an option of dhcp address required under the advanced tab. Do we need to use this option, if we are defining a normal dhcp pool in our controller for that ssid.
View 3 Replies
View Related
Jul 15, 2012
Is it possible to regain the PSK from the security tab from a 5500 controller in clear text?I need to check the current used password without resetting it, but I fail to find the password in the configuration (CLI & web interface)Obviously I do have admin access to my controller.
View 2 Replies
View Related
Jul 5, 2011
The Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
View 1 Replies
View Related
Apr 18, 2013
I need to know the command to take the Backup and Restore of IOS Image of 6513 through tftp server.
View 6 Replies
View Related
Jun 15, 2012
i have cisco CAP 3602e series access point to work with 5500 series controller with code 7.0i did not find VCI option 60 for this type of APs to configure DHCP. How I can let these APs will join the controller, i mean through which process DNS discovery methode and what about if i need to configure option 60 and 43 in dhcp for ap joining process to controllers.
View 4 Replies
View Related
Nov 4, 2012
I need to take the backup of configuration file for WLAN Controller 4420, I tried all the possibilities given in the documentation but the backup fails, I have main confusion with the file name to be backedup, i am not able to findout the configuration filename any where even when i use CLI?
View 1 Replies
View Related
Jun 7, 2011
in one of the sites, the client has an exisiting 4402 controller which he moved to the DMZ in order to set it as an anchor & he purchased two new 5508 controllers to control the corporate APs. I configured all the parameters needed for the guest anchoring & then I tested the connection but there was an issue. (all the controllers are running the same firmware version)after testing the setup, the guest users could get an IP from the internal DHCP of the anchor controller (in DMZ), but then they cannot reach the internet or anything outside the anchor controller.Cisco confirmed that the 4400 is fully compatible with the 5500 to work in an anchor-foreign secnario as long as they are running the same firmware version. yet, when I temporarily used one of the 5500 controller in the DMZ as an anchor & I applied the exact same configurations on it as the 4400, it worked perfectly without any issues.
note: on the anchor controller (4400), the management & AP-manager interfaces reside on the same subnet & the wireless guest SSID is also mapped to the management interface. (may be this setup is causing the issue) but on the 5500 it is working just fine?
View 2 Replies
View Related
Nov 20, 2012
Having an issue with my WLC 5500 and client connectivity. This just started today. Clients will connect for a short period of time and then drop off. WLC appears fine with the exception of a bunch of trap errors. I've rebooted the WLC but this did not clear the issue.
View 3 Replies
View Related
Jun 19, 2012
I am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
View 6 Replies
View Related
Feb 16, 2013
We have inherited a 5508 controller running 7.0 code and WCS running 7.0 code. This site did not have a backup controller. So we have installed a wism as a backup controller. The problem is no one can seem to remember the pre shared keys for the wlans on the primary controller. Can I use WCS to duplicate the wlans to the secondary controller and have the psk copied?
View 3 Replies
View Related
May 1, 2012
i need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies
View Related
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Aug 12, 2012
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies
View Related
Jun 2, 2013
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies
View Related
Dec 6, 2012
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
View 1 Replies
View Related
Apr 26, 2012
MSE can not boot.MSE show error log. [code] How to recovery MSE 3310,I find in documents not show method recovery. Any solution recovery MSE 3310
View 2 Replies
View Related
Jun 19, 2012
Where is the link to download recovery IOS for AP1130AG.
View 4 Replies
View Related
Jul 9, 2012
I have upgraded my new WLC to version 7.0.98.218. I noticed the N/A for the Field recovery version. On my old 4402 it is called the Emergency Image Version, and it is 5.2.157.0
How do i get a recovery version on the WLC?
View 2 Replies
View Related
Mar 14, 2013
My questions is in relation to disaster recovery, for wireless. We have our main data center, in the US, with two 5508 controllers. We have a DR location, in Europe, with two 5508 controller. We're upgrading our 5508's to the 7.4 code, so that we can take advantage of the RP port for our controllers. With that said, is there a way to make the US and Europe controllers redundant?
If there's a disaster, in the US, would the AP licensing, and AP's attach to the European controllers? Our AP's are set up with HA. I'm more concerned about the licensing flipping over to the DR controllers. I've tried researching this topic, and can't really find anything on it.
View 4 Replies
View Related
Feb 4, 2012
I did a System Recovery after my computer had the virus that redirected me to a pop ups and different websites every time. After System Recovery I no longer have internet connection on the computer I used. All the other devices and computer can access my router but not the computer that I've used System Recovery on. I looked at Device Manager and all of my Networking Devices are working properly. I even looked at Wireless Zero Configuration and the Startup type is Automatic and the Service Status is Started.I go into Network Connections and my USB Adapter has an red X on it. I right clicked properties and looked at wireless networks and the preferred networks is grayed out[CODE]
View 3 Replies
View Related
