Cisco Wireless :: Password Recovery LAN Controller 4402?
Jul 20, 2008how to password recovery Wireless LAN Controller 4402
View 3 Replies
ADVERTISEMENT
Cisco WAN :: Recovery Password 2801 With No Service Of Recovery
May 1, 2012i need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies View RelatedCisco Wireless :: 5500 How To Reboot Controller To Use Backup Recovery Image
Jun 22, 2012I have 5500 controller with firmware 7.0 installed from the factory. Due to some reasons, I understood that other existing wireless infrastructure runs on firmware 6.0, and hance i need to downgrade the 5500 series to 6.0 . During the bootup, i could see there is another image called backup recovery image, which is running on version 6.0. How can i reboot controller to use the older image , which is from backup recovery image. I couldnt find it in the configuration guide.
View 4 Replies View RelatedCisco Wireless :: Connecting WET200 To Wi-Fi Controller 4402
Jun 30, 2010We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?
View 4 Replies View RelatedCisco Wireless :: 5508 And 4402 Controller Anchoring?
Mar 11, 2012I am running 5508 wireless controllers. I pass along another agency's WLAN across my wireless network that is anchored to their older 4402 controller.
I wish to run the new 3600 series APs and am planning on migrating to NCS and the new 7.2 code.
I know that the older 4400 series controllers will not handle the newer 7.1 or 7.2 code. However, i still wish to maintain this anchor relatiosnhip with the older 4402 controller. I need to know if this will work or not.
Cisco Wireless :: AP LAP1142N Can't Join Controller - 4402
Apr 11, 20121) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
Cisco Wireless :: Replace 4402 With 5508 Controller
Oct 6, 2012I'd like to replace my 4402 Wireless controller with a new 5508. I have migrated the exact configuration from my 4404 controller to the 5508 and they are both running the same version of code. I'm worried that if I replace the 4402 with the 5508 controller, the Access Points will not rejoin to the new controller or they will join but will have lost their configuration e.g. AP Name/location etc etc. AP models registered to the existing controller are 1131, 1142 and 3502. I am also using Cisco WCS.
As long as the new controller has the exact same configuration, is it possible to replace the 4404 with the 5508? Will the existing Access Points join the new controller? Is there any other configuration required? I have read about doing this using mobility groups however would rather not if possible.
Cisco :: Wireless Controller 4402 - Printing Setting Via Wi-Fi?
Oct 16, 2012I have a wireless printer on an internal wireless network. I have a laptop connected wirelessly on the same internal network. When both devices are connected to the same network I cannot connect to the printer. If I change my laptop over to the guest wireless or to a wired lan, I can see the printer. I vendor stated that within the 4402 wireless controller there is a setting to allow wifi to wifi connections on the same internal network. I am trying to figure out what that setting is called and where I might look for the setting within the wireless controller.
View 1 Replies View RelatedCisco Wireless :: LAN Controller 4402-12K9 Upgrade To 25 APs
Jan 27, 2013I have a 4402-12-k9 controller and I need to upgrade to 25 APs Can I buy a 12 or 25 license upgrade to this controller?
View 7 Replies View RelatedCisco Wireless :: 4402 And 5508 Controller Installation
Oct 30, 2012My client has on cisco 4402 controller running with 48 AP on this. Client requires to add another 25 AP but licence on the current controller is not supported client bought another controller 5508 with 25 AP.
I have been tasked to installe 5508 with conjestion of 4402. I have make the software version on both of them as below
AIR-CT5500-K9-7-0-235-3.aes
AIR-WLC4400-K9-7-0-235-3.aes
To match the same IOS version on both the controller. I have following challenges with me.
- 5508 will registered 25 AP while .. 4408 will continue with 48 AP.
- 5508 is going to be in DC and it will be directly connected to firewall as default gateway for guest SSID. 4402 is going to be on another building.
- How can I make sure that Users connected to AP registered with 4402 will have the same deafult gateway as 5508. Thre is no layer 2 connectivity between this two controllers.
- There is no romaing going to happen between this two controller as both are two different locations and user will leave one location will disconnect and it joines bak when it reach to another controller.
- Is there any way to configure 5508 as master and 4402 as slave kind of connections?
Cisco Wireless :: Set Aironet 1232AG-A-K9 As Repeater While Using 4402 Controller
Oct 8, 2012Is it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller? I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using. I have some omni antennas and a yagi directional that I was planning on using.Everything I am reading talks about configuring the AP while in automous mode, not while running the lightweight image.
View 2 Replies View RelatedCisco Wireless :: AP 1131 AG Do Not Associate To Controller 5508 Or 4402
Apr 18, 2013I have 10 Access-Point model 1131 AG are new AP.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
Cisco Wireless :: How To Modify RADIUS Servers On 4402 Controller
Jul 20, 2010I have several controllers, including a 4402 running 6.0.188.0 software and I need to modify the Radius servers that it uses. Currently I have three servers listed;
1 - 10.246.194.16
2 - 10.200.31.78
3 - 10.247.50.56
I would like to delete server 1 which is being retired and replace it with a new server 1. I suspect, once i get servwe 1 deleted, the server 1 option would become available when I create a new server. I went into the controller and disabled server one, but every time I try and delete it, I get the "Server in use either on a specific WLAN or Mesh Radius Server Configuration" error. I can't find anywhere this server is still in service and being used, either by a WLAN or a Mesh. I've tried several different variances to modify this. What I hope to avoid is the need to reset the controller. I have a total of seven controllers that I need to make this modification to, and It will be ugly if I have to reboot these units. Hospital mission critical stuff.
Cisco Wireless :: Unable To Upgrade Lan Controller 4402 Firmware
Mar 1, 2012I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
Cisco Wireless :: 4402 Controller - Client Reauthenticates Occasionally
Mar 15, 2013I have 3 WLC 4402 controller connected to an ACS Server and Cisco 1252G AP. Previously the wireless networks works fine but for two weeks now most of the clients experiencing reauthentication frequently, Some experience it every 5 mins even if they are browsing or idle and not moving. I've check the session time out settings in the wlc and it was configured for 30 mins as default. I have around 900 student clients connecting every day.
View 4 Replies View RelatedCisco Wireless :: Internal DHCP Server On 4402 Controller
Apr 8, 2008I am trying to setup a guest vlan. I set up an interface for the guest vlan on my 4402 controller. I assigned the guest vlan interface an IP of 192.168.2.10 with a 24 bit subnet mask.
This vlan will go to my DMZ where there is no DHCP server so I need to setup the internal DHCP server. I created a new scope but I'm having trouble with what to put in the Network field for the DHCP scope. The pool addresses are 192.168.2.100-200. with a 24 bit subnet mask.
Every time I try to apply the configuration I get an "error in setting DHCP scope network and netmask".
I've tried using:
192.168.2.10
192.168.2.255
192.168.2.254
as entries for the Network setting but no go. The docs say to enter the IP address used by the management interface with subnet mask applied.
I was assuming they meant the interface for the guest vlan.
Cisco Wireless :: How To Use Mac Filtering With Wildcards On 4402 Wlan Controller
Aug 3, 2011we use wlc 4402 (Software Version 7.0.98.0) and want to allow only several wlan nic vendors to connect to a wlan ssid.According to this, is it possible to configure MAC Filtering with wildcards, e.g. aa:bb:cc:* ?
View 1 Replies View RelatedCisco Wireless :: Software Version Upgrade For 4402 LAN Controller
Jun 5, 2012We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
What is the latest version to upgrade the WLC?
Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?
Cisco Wireless :: 4402 - Controller Crashed With Reaper Reset
Jan 17, 2012We have upgraded to latest IOS but observed this box is hitting a bug which was resolved in the earlier releases but not seen in 4402.
Is this related to hardware issue or a software bug only.
CSCtg94715
CSCtk83586
CSCso90721
Error! Software watchdog on task dot11b expired! Reaper Reset: Task "dot11b" missed software watchdogError! Software watchdog on task apfMsConnTask_0 expired! Reaper Reset: Task "apfMsConnTask_0" missed software watchdogError! Software watchdog on task apfReceiveTask expired! Reaper Reset: Task "apfReceiveTask" missed software watchdogError! Software watchdog on task radiusTransportThread expired! Reaper Reset: Task "radiusTransportThread" missed software watchdogError! Software watchdog on task ccxL2RoamTask expired! Reaper Reset: Task "ccxL2RoamTask" missed software watchdogError! Software watchdog on task dot1xMsgTask expired! Reaper Reset: Task "dot1xMsgTask" missed software watchdogError! Software watchdog on task spamReceiveTask expired! Reaper Reset: Task "spamReceiveTask" missed software watchdogError! Software watchdog on task dtlArpTask expired! Reaper Reset: Task "dtlArpTask" missed software watchdogReaper is kickin' into high gear Task dtlArpTask is consuming 0% CPU! (0% user, 0% system) Frame 0: 0x10004708: sighup_handler+84
************************************************************
* Start Cisco Crash Handler Serv *
************************************************************
Sys Name: HJ_Wireless_Controller
Model: AIR-WLC4402-50-K9
[code].....
Cisco Wireless :: 4402 Guest Anchor Controller 5508 Software 7.2
Nov 6, 2012We currently have all of our foreign AP controllers on software version 7.0.116. This consists of a mixture of 4400 and 5508 WLC's. Our guest anchor is a 4402 on version 7.0.116. We are replacing the guest anchor with a 5508. We are also upgrading our 5508 wireless controllers to version 7.2 to support the 3600 series AP's. My question is what is the recommeded code that the anchor controller should be on? Should it also be upgraded to 7.2? If we upgrade the anchor controller to version 7.2, will this affect anchoring to 4400 series foreign controllers still on7.0.116?
View 9 Replies View RelatedCisco Wireless :: 4402 WLC Management / Local Controller Versus Cloud
Feb 26, 2013We are currently looking to upgrade (re-design) our wireless network at our college. Any experience going from a local, controller-based wireless network to a cloud-based controller? If so, what have you found the pros and cons to be?
If you thought about going to a “cloud solution”, what stopped you?
We are currently running wireless at our 3 primary campus locations, and looking to add it to our 3 satellite locations. We use 4402 WLCs at our primary locations with a mix of 1140 and 1240 APs.
Cisco Wireless :: 4402 Access Points Without Wireless LAN Controller
May 8, 2012I have cisco 4402 Wireless LAN Controller with Cisco Access Point (AIR-LAP1252G-E-K9), everything is running smoothly.How come i use my Access Points without Wireless LAN Controller, is there any possibility then which AP model would be suitable?
View 2 Replies View RelatedCisco :: ACS 5.1 Password Recovery Procedure
Oct 20, 2011where I can find a CLI password recovery procedure for the administrator account?
View 1 Replies View RelatedCisco Firewall :: PIX 501 Password Recovery
Nov 18, 2011I have problem recovering my cisco 501 pix password. I followed instructions on this pageurl... but it seems its not working. I cant ping my TFTP Server on my pc. I tryed to disable firewall on my pc, i did a fresh install Windows but still i cant ping my TFTP Server on my PC.
View 8 Replies View RelatedCisco Firewall :: PIX 525 Password Recovery?
Dec 13, 2011As I make a password recovery to a Cisco PIX 525 Version 6.3(3)?
View 1 Replies View RelatedCisco :: AIR-LOC2710-L-K9 Password Recovery?
Jun 1, 2011I just bought one of these in and it was in production and I have no way of getting a hold of the login information. Is there a way to wipe these to factory defaults? I have been looking everywhere with no such luck.
View 2 Replies View RelatedCisco WAN :: Password Recovery For 3548 Xl?
May 6, 2011I am a student pursuing a CCNA certification currently. I recently came across a lot of 3548 xl switches. They power up fine, post with out problem and load flash. The problem I am running into is that the console is password protected. I have found the password recovery procedure for this switch, but it requires the use of the mode button. I have tried this process several times and the flash file is loaded with the startup config file. How do I perform a password recovery on a switch with a broken mode button?
View 1 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.0.021 CLI Password Recovery
Apr 10, 2012how to recover ACS 5.0.021 CLI password.I dont have 5.0.021 cd with me can i use 5.2 cd to recover the same ?
View 1 Replies View RelatedCisco WAN :: 2960 - Password Recovery
Mar 12, 2012To configure my Cisco, I use the console cable but as I have no serial port on my PC, I use a USB to serial cable which I plug the console. I had lost this USB cable -> serial but I found another one. So I started to configure my Cisco by copying from an existing config. I found out that a prior the converter is defective and copy the wrong config.
I had copied the enable secret password and it badly copied! No luck, I made a copy run start. Therefore more accessible to Cisco! When I start the Cisco, I see what activated "the Mechanism password-recovery is enabled". so I followed the procedure Cisco
I go flash_init: OK but when I type "load_helper" Unknown command it say to me .... I'm stuck!
The model is my Cisco: Cisco WS-C2960G-24TS-S
SW Version 12.2(55)SE3
Sw image C2960S-UNIVERSALK9-M
Cisco WAN :: 877 - No Password Recovery / IOS Lost
Oct 2, 2011I have a couple of 877s which have "no service password recovery" set and something has happened to the flash or the IOS has been lost for one reason or another.
When trying to boot the routers, they all display similar to this, which then repeats:
[code]....
Or words to the effect of there being no IOS at all, unable to boot, but the result is the same, it just loops and there's nothing I can do to break the sequence!
I've tried taking the flash from a working 877 and replacing the card but this doesn't work and unfortunately, putting the once working strataflash card back in the working 877, it gets the same problem!
Cisco VPN :: Pix 515E Password Recovery
Jun 26, 2011I have a cisco 515e pix but where I bought it from did not get the machine back to default. I boot it up and get to the user prompt, type enable and it asks for a username and then a password. I am new to this and am have no problems with router and switch password recoverys but when I look at the cisco documentation it is a bit overwhelming and I am not quite sure what it is that they want me to do to fix this. I have downloaded all the password recovery software loads and have the one I need for 6.x which is what the box is running I am just not sure what it is that I need to do. Can I use that recovery software from directly from my pc using a tftp server?
View 1 Replies View RelatedCisco :: Setting Up NPS With 4402 Wlan Controller?
Jul 4, 2011I am currently running a Cisco 4402 Lan controller, I have a Wlan that is running unsecured and i wanted to add a simple web policy log in, so i set up an NPS server on a local DC. I have the two talking . when i go to login at the web login page I get the Error Login Error. When i look at the NPS logs it says: "Network Policy Server granted full access to a user because the host met the defined health policy" . So it has to be in my Cisco set up somewhere seems pretty simple
View 2 Replies View RelatedCisco :: 4402 WLAN Controller - New Clients Not Getting IP?
Jan 14, 2013Recently (within the past 2 months) I've been having some issues with my 4402 wLAN controller.
The issue is thus:
1) New wireless clients (those without exsisting DHCP leases) are unable to properly connect to our wireless network.
2) Those same systems (and other systems) have no issue getting online via a wired connection (where available).
3) Devices like iPad, tablets, laptops partially connect but do not get a valid IP address.
Our config:
1) DHCP is handled by a seperate server (NOT the 4402 - it's DHCP setting is disabled)
2) Our wLan is not on a seperate network than our wired LAN
3) Wireless devices attempting to connect include iPads and laptops mostly.
4) We're a school with about 300 systems (primarily Windows XP machines).
5) 25 access points controlled by the 4402 (our only wLAN controller)
Important Notes:
1) No configuration changes have been made to DHCP or the 4402 device in a couple years.
2) 4402 Software Version = 4.0.217.0
The problem first showed up a bit over a month ago. I first thought the issue was DHCP server related , so I started there and didn't find any obvious issues. I did restart the DHCP server (which at that point had an uptime of somewhere over 700 days).
I then also checked the web interface of the 4402 to see what it was reporting. I noticed a somthing:A) As shown in the "WLAN_Issue_EDIT.png" the client count on the controller is showing 628 current clients. We don't have many devices in our entire campus.
I rebooted the controller after hours and that seemed to allievete the issue. Since then, the current client count hasn't ever gone above 60.
Now today I'm having the same issue regarding new clients getting IP addresses. The client count isn't real high on the WLAN controller and I don't see any other obvious issues. I'm torn between this being a DHCP issue or the controller issue (or a combination of the two).
The reason I don't think it's directly DHCP related is that all wired clients seem to be getting address fine.Plus, I've set my tablet device to a static address and it still cannot connect via wifi.
**Update** I've now rebooted the controller and the problem persists (at least on the nearby iPad - Will confirm other devices shortly).