Cisco Wireless :: Connecting WET200 To Wi-Fi Controller 4402
Jun 30, 2010
We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?
I'm having a problem with a cisco bridge WET200 we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge but the equipment is not communicating with the gateway, with nothing!WLC always appears the following error:
WiSM-slot9-1) >debug client XX:XX:XX:XX:XX:XX (WiSM-slot9-1) >*apfReceiveTask: May 23 12:03:27.953: XX:XX:XX:XX:XX:XX Deleting mobile on AP XX:XX:XX:XX:XX:XX(0) *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Adding mobile on LWAPP AP XX:XX:XX:XX:XX:XX(0) *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Association received from mobile on AP XX:XX:XX:XX:XX:XX *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX 0.0.0.0 START (0) Changing ACL 'Guest' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393) *apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Applying site-specific IPv6 override for station XX:XX:XX:XX:XX:XX - vapId 5, site 'default-group', interface
[code]....
i have test command config network ip-mac-binding disable but It does not connect....when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured?
I'm having a problem with a cisco bridge WET200.we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge [code] but the equipment is not communicating with the gateway, with nothing!
when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured
I've just purchased 2 WET200 wireless bridges for our organisation, with the intention of using them to create a wireless bridge between 2 buildings.I've followed this guide here: url...and I'm unable to configure any kind of security other than WEP. More disconcertingly, the foot of that guide states:WET200 only supports WEP for the Wireless Security."Surely this can't be the case? All the marketing blurb states clearly that the WET200 supports WPA2, and I would have thought WPA2 was a given for any wireless product sold today, especially a business grade product. Have I misunderstood what this device can do?
I am running 5508 wireless controllers. I pass along another agency's WLAN across my wireless network that is anchored to their older 4402 controller.
I wish to run the new 3600 series APs and am planning on migrating to NCS and the new 7.2 code.
I know that the older 4400 series controllers will not handle the newer 7.1 or 7.2 code. However, i still wish to maintain this anchor relatiosnhip with the older 4402 controller. I need to know if this will work or not.
1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set ?= DEFAULT_ROUTER=10.0.0.1 Default_router=10.9.99.1 ENABLE_BREAK=yes
I'd like to replace my 4402 Wireless controller with a new 5508. I have migrated the exact configuration from my 4404 controller to the 5508 and they are both running the same version of code. I'm worried that if I replace the 4402 with the 5508 controller, the Access Points will not rejoin to the new controller or they will join but will have lost their configuration e.g. AP Name/location etc etc. AP models registered to the existing controller are 1131, 1142 and 3502. I am also using Cisco WCS.
As long as the new controller has the exact same configuration, is it possible to replace the 4404 with the 5508? Will the existing Access Points join the new controller? Is there any other configuration required? I have read about doing this using mobility groups however would rather not if possible.
I have a wireless printer on an internal wireless network. I have a laptop connected wirelessly on the same internal network. When both devices are connected to the same network I cannot connect to the printer. If I change my laptop over to the guest wireless or to a wired lan, I can see the printer. I vendor stated that within the 4402 wireless controller there is a setting to allow wifi to wifi connections on the same internal network. I am trying to figure out what that setting is called and where I might look for the setting within the wireless controller.
My client has on cisco 4402 controller running with 48 AP on this. Client requires to add another 25 AP but licence on the current controller is not supported client bought another controller 5508 with 25 AP.
I have been tasked to installe 5508 with conjestion of 4402. I have make the software version on both of them as below
To match the same IOS version on both the controller. I have following challenges with me.
- 5508 will registered 25 AP while .. 4408 will continue with 48 AP. - 5508 is going to be in DC and it will be directly connected to firewall as default gateway for guest SSID. 4402 is going to be on another building. - How can I make sure that Users connected to AP registered with 4402 will have the same deafult gateway as 5508. Thre is no layer 2 connectivity between this two controllers. - There is no romaing going to happen between this two controller as both are two different locations and user will leave one location will disconnect and it joines bak when it reach to another controller. - Is there any way to configure 5508 as master and 4402 as slave kind of connections?
Is it possible to set an Aironet 1232AG-A-K9 as a repeater while still using a 4402 controller? I have some wireless security cameras in our parking lots that I need to extend wireless to and I have a handful of 1232 points that I am not using. I have some omni antennas and a yagi directional that I was planning on using.Everything I am reading talks about configuring the AP while in automous mode, not while running the lightweight image.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
I have several controllers, including a 4402 running 6.0.188.0 software and I need to modify the Radius servers that it uses. Currently I have three servers listed;
I would like to delete server 1 which is being retired and replace it with a new server 1. I suspect, once i get servwe 1 deleted, the server 1 option would become available when I create a new server. I went into the controller and disabled server one, but every time I try and delete it, I get the "Server in use either on a specific WLAN or Mesh Radius Server Configuration" error. I can't find anywhere this server is still in service and being used, either by a WLAN or a Mesh. I've tried several different variances to modify this. What I hope to avoid is the need to reset the controller. I have a total of seven controllers that I need to make this modification to, and It will be ugly if I have to reboot these units. Hospital mission critical stuff.
I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
I have 3 WLC 4402 controller connected to an ACS Server and Cisco 1252G AP. Previously the wireless networks works fine but for two weeks now most of the clients experiencing reauthentication frequently, Some experience it every 5 mins even if they are browsing or idle and not moving. I've check the session time out settings in the wlc and it was configured for 30 mins as default. I have around 900 student clients connecting every day.
I am trying to setup a guest vlan. I set up an interface for the guest vlan on my 4402 controller. I assigned the guest vlan interface an IP of 192.168.2.10 with a 24 bit subnet mask.
This vlan will go to my DMZ where there is no DHCP server so I need to setup the internal DHCP server. I created a new scope but I'm having trouble with what to put in the Network field for the DHCP scope. The pool addresses are 192.168.2.100-200. with a 24 bit subnet mask.
Every time I try to apply the configuration I get an "error in setting DHCP scope network and netmask".
I've tried using:
192.168.2.10 192.168.2.255 192.168.2.254
as entries for the Network setting but no go. The docs say to enter the IP address used by the management interface with subnet mask applied.
I was assuming they meant the interface for the guest vlan.
we use wlc 4402 (Software Version 7.0.98.0) and want to allow only several wlan nic vendors to connect to a wlan ssid.According to this, is it possible to configure MAC Filtering with wildcards, e.g. aa:bb:cc:* ?
We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
What is the latest version to upgrade the WLC?
Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?
We currently have all of our foreign AP controllers on software version 7.0.116. This consists of a mixture of 4400 and 5508 WLC's. Our guest anchor is a 4402 on version 7.0.116. We are replacing the guest anchor with a 5508. We are also upgrading our 5508 wireless controllers to version 7.2 to support the 3600 series AP's. My question is what is the recommeded code that the anchor controller should be on? Should it also be upgraded to 7.2? If we upgrade the anchor controller to version 7.2, will this affect anchoring to 4400 series foreign controllers still on7.0.116?
We are currently looking to upgrade (re-design) our wireless network at our college. Any experience going from a local, controller-based wireless network to a cloud-based controller? If so, what have you found the pros and cons to be?
If you thought about going to a “cloud solution”, what stopped you?
We are currently running wireless at our 3 primary campus locations, and looking to add it to our 3 satellite locations. We use 4402 WLCs at our primary locations with a mix of 1140 and 1240 APs.
I have cisco 4402 Wireless LAN Controller with Cisco Access Point (AIR-LAP1252G-E-K9), everything is running smoothly.How come i use my Access Points without Wireless LAN Controller, is there any possibility then which AP model would be suitable?
We have a controlled setup comprising of a 4402 WLC in our Data Centre and 1242AG LWAPs in our branches.The Wireless works well with a mixture of locally switched (h-reap) and centrally switched WLANs.I have a problem where Android devices don't seem to function as they should.I have been using an Android phone (HTC Desire, currently running 2.3.4 OS, but has been a persistant issue since 2.1) and it connects to my home wireless (and others) fine, but when connecting to the Wireless LAN at the office, it connects fine and gets assigned an IP address, but NO data flows. None, like there is no connection at all. I have just been using it on 3G. I figured it might have just been an issue with the hardware, so didn't bother too much.I have just purchase a new tablet (ASUS Transformer, Currently running 3.1 OS) and this does the same thing.I have tried publishing a new WLAN and have tried all types of encryption and authentication al the way down to open and still, no data flow. I have tried statically setting the IP details and still nothing.Interestingly, When I attended the last Cisco Live conference in Melbourne this year, I had my phone and it displayed the same behaviour on the Cisco supplied wireless, BUT, there was a second IPv6 enabled, when connected to that everything worked fine.
I am currently running a Cisco 4402 Lan controller, I have a Wlan that is running unsecured and i wanted to add a simple web policy log in, so i set up an NPS server on a local DC. I have the two talking . when i go to login at the web login page I get the Error Login Error. When i look at the NPS logs it says: "Network Policy Server granted full access to a user because the host met the defined health policy" . So it has to be in my Cisco set up somewhere seems pretty simple
Recently (within the past 2 months) I've been having some issues with my 4402 wLAN controller.
The issue is thus:
1) New wireless clients (those without exsisting DHCP leases) are unable to properly connect to our wireless network.
2) Those same systems (and other systems) have no issue getting online via a wired connection (where available).
3) Devices like iPad, tablets, laptops partially connect but do not get a valid IP address.
Our config:
1) DHCP is handled by a seperate server (NOT the 4402 - it's DHCP setting is disabled)
2) Our wLan is not on a seperate network than our wired LAN
3) Wireless devices attempting to connect include iPads and laptops mostly.
4) We're a school with about 300 systems (primarily Windows XP machines).
5) 25 access points controlled by the 4402 (our only wLAN controller)
Important Notes:
1) No configuration changes have been made to DHCP or the 4402 device in a couple years.
2) 4402 Software Version = 4.0.217.0
The problem first showed up a bit over a month ago. I first thought the issue was DHCP server related , so I started there and didn't find any obvious issues. I did restart the DHCP server (which at that point had an uptime of somewhere over 700 days).
I then also checked the web interface of the 4402 to see what it was reporting. I noticed a somthing:A) As shown in the "WLAN_Issue_EDIT.png" the client count on the controller is showing 628 current clients. We don't have many devices in our entire campus.
I rebooted the controller after hours and that seemed to allievete the issue. Since then, the current client count hasn't ever gone above 60.
Now today I'm having the same issue regarding new clients getting IP addresses. The client count isn't real high on the WLAN controller and I don't see any other obvious issues. I'm torn between this being a DHCP issue or the controller issue (or a combination of the two).
The reason I don't think it's directly DHCP related is that all wired clients seem to be getting address fine.Plus, I've set my tablet device to a static address and it still cannot connect via wifi.
**Update** I've now rebooted the controller and the problem persists (at least on the nearby iPad - Will confirm other devices shortly).
I am enabling our wireless controllers to use 802.1x authentication for our wireless clients. Both computer and user are provided with certificate from CA server.I have 9 APs and 2 controllers installed in my infrastucture, one of the controllers is working fine with setting specified above but the other one is not.Both has same configuration and both seems identical with same model and IOS.
I have a Cisco 4402 Wireless LAN Controller and 4 x AIR-LAP1131AG-A-K9 access points.We run a combination of [WPA +WPA2]Auth(802.1x) as well as [WPA2]Auth(PSK), most people have their own login credentials...The primary client devices are MacBooks and iPhones, with some Windows and other mobile manufacturer being the minority.
The Issue I have one user (using a recent MacBook Air, latest OS, using Auth(802.1X) ), that keeps getting disconnected for no apparent reason, the user account has been setup exactly the same as every other user and his laptop doesn't have this issue when connected to other WiFi networks.It's worth noting: I noticed this particular user has a lot of "Decrypt Failed" (currently 213) associated with his MAC address, no other user on our network has a single "Decrypt Failed" associated with their MAC...
I have 2 4402 WLC running 7.x.x.x code. I also have some 1510 Mesh- L WAPs that require an old version of code. I need 4.1.192.22M for those. Is it possible to bring up a 3rd controller running this old code with the other 2 4402's running modern code? What will break? I know that anchoring and mobility might get messed up. What are the other caveats?
I need Some information for Connecting my New Access point ( Cisco AIRLAP 1242AG) with WLC(4402) ControllerIn our network set up we have two WLC(4402) we needs to Connect this New Accesspoint To one of our WLC,My Access point is brand New. I need to Know what all i have to do inorder to connect this AP to the controller (from Acesspoint perspective & WLC perspective),I need to Know what I need to do in AP to connect to the Controller,Do i need to Assign Static IP Address forAP or after connecting to the switch it automatically gets ip from DHCP and regsiter with controller??
I am trying to connect a Zodiac iAqualink wireless pool equipment controller to my home network (WRT54G) without success. This is a 802.11b device. My router is set to mixed mode. What I have tried:
1. Set it up as suggested in the instructions: WEP2 security, double checked SSID and password 2. Set it up without wireless security 3. Changed channels 4. Set mode to 802.11b
In all cases the LED on the iAqualink that is supposed to indicate that it is connected to the network illuminates properly, but I can never find the device using EasyLink Advisor.
