Cisco :: Information For Connecting Access Point To WLC 4402
Nov 15, 2011
I need Some information for Connecting my New Access point ( Cisco AIRLAP 1242AG) with WLC(4402) ControllerIn our network set up we have two WLC(4402) we needs to Connect this New Accesspoint To one of our WLC,My Access point is brand New. I need to Know what all i have to do inorder to connect this AP to the controller (from Acesspoint perspective & WLC perspective),I need to Know what I need to do in AP to connect to the Controller,Do i need to Assign Static IP Address forAP or after connecting to the switch it automatically gets ip from DHCP and regsiter with controller??
View 38 Replies
ADVERTISEMENT
Oct 3, 2011
I have a Cisco 870 integrated service router and 3 Cisco Aeronet 1180 Access Points.I have configured the router to act as a DHCP server. with all four /26 subnets in a seperate address pool.the first one is for the routers wireless interface and works fine.but the other 3 are for each of the wireless access points, that are used for internet access, but have to operate independently (i.e. the clients on each must not be able to access anything other than the devices associated with that access point and the internet.
The problem I are having is that the router doesnt distribute DHCP information via the access points so the clients on all the access points are not recieving any internet connection at all, but are connecting to the access points, and the LED for the access points suggest that they are connected t the router, the router accnowledges their existence but is not transmitting through the fast ethernet switch ports. but is communicating with a wired printer that is associated with the wireless vlan.
Each access point is on its own vlan, and the switchport access vlan command has been used. only the five static addresses have been excluded from the address pool. the router, the three access points and the printer adresses are static. the printer is working despite being the only device on the /24 network all other addresses are on the /26 networks. this to my knowledge shouldent work but it does, which is handy because the printer software doent support subnetting.The simulation I have ran say that only the printer shouldent work, but its the access points that are not working how they should. I have studied the configuration of the router and access points, and came up empty on why they are not recieving DHCP information.
I are not even able to telnet to them, despite having an address setup. I have not set up a routing protool on the router due to it being the only router. I have checked the interfaces fa0 to fa3 and they are line up protocol up, the wireless is line up protcol up, the vlans are line up protocol down, except the one asociated with the wireless which is line up protocol up (I believe the protocol only goes up when a device is connected to it).
View 9 Replies
View Related
Feb 14, 2012
We have an Cisco Aironet 1130AG access point which is deployed as Stand Alone Access point, connected to Cisco 2960 Switch.Now we want to configure an Guest Wifi Access for guest users , for accessing internet ,Is it possible to configure Guest wifi for stand alone access point,( Bcoz i created in WCS, i am not sure about stand alone), i read in articles like create new vlan for Guest account & assign it like that , but not clear.
View 7 Replies
View Related
Oct 13, 2011
We are expanding our wireless infrastructure by adding further access points AIR-AP1242AG-E-K9.We use four WLC 4402 running version 6.0.188.0 as a fail over pair.What is the maximum limit the WLC can handle ?What is the recommended limit one WLC can handle ?We can divide the load on the controllers but in case of a failover one WLC will manage all access points.
View 4 Replies
View Related
Mar 13, 2012
need an access point configured in the user minimum because I was looking and some had up to 49 LAP connections at the same time. I have a WLC 4402 VERSION 7.0.98
View 1 Replies
View Related
Apr 4, 2012
Does the Cisco 1262N Lightweight Access Point (AP) work's with Wireless LAN Controller 4402?
View 1 Replies
View Related
Oct 21, 2012
I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None
View 3 Replies
View Related
Aug 22, 2011
I have a Cisco 2811 router with C288nm-advsecuruityk9-mz.151-4-4.M.bin IOS version.The router has two LAN interface FE 0/0 and FE 0/1.The router have too, two interfaces ADSL ATM0.0.0 and ATM 0.0.1, both are connect to internet..I need the next configuration.The interface FE 0/0 is directly connect to a Switch A.The interface FE 0/1 is directly connect to a Access Point Cisco.The Access Point and the Switch is not connecting between.The subnet of Switch A and AP are different (Switch A 192.168.180.0/24 and AP 192.168.181.0/24)The devices in the switch A have dynamic IP address, the router must be a DHCP pool to assign theses IP.The device in the AP have dynamic IP address, the router must be a DHCP pool to assign theses IP.I created two DHCP pools in the router, one for the subnet 192.168.180.0 and other for 192.168.181.0, but the devices of FE 0/0 assign IP of 192.168.180.0 or 192.168.181. 0, but not only in the 192.168.180.0.
View 5 Replies
View Related
Jan 25, 2012
I have two locations separated by less than 300 meters. In each zone I have an Access Point and in only one zone (let's call it Zone B), I have two IP Cameras. The idea is to connect these two cameras to my AP located at Zone B, and then, send this signal to my other AP to get this cameras in a LCD. First of all, I want to know in which mode should the APs be connected, I mean, in which "Operation Mode". I have three options:
-AP Client Router
-AP Router
-AP
And if I choose AP mode:
-AP:
+ Access Point
+ Client
+ WDS Bridge
+ Repeater
PD: The APs Model: TL-WA5210G
View 14 Replies
View Related
Mar 21, 2011
My home network currently has a Linksys router (essentially acting as a wireless access point) in a distant part of the house connected to my main router, a Netgear WNR2000, and this configuration is working fine.
I want to replace the main router with a new D-Link DIR-655 (better parental controls). When I swap in the new router and get the cables plugged in in the same manner as they are in the Netgear router, computers connecting wirelessly to the Linksys router can no longer access the Internet.
The Netgear router is set up with an IP address of 192.168.4.1. The Linksys is 192.168.2.1, and the D-Link is at the default 192.168.0.1.
View 1 Replies
View Related
Sep 19, 2009
I use a Cisco 871W router for my office in home -- I have Wifi working and want to add my new Blu-Ray player to the network -- I bought a WAP54G to use as a wireless bridge assuming i woudl just connect the WAP to the BLU-Ray with a ethernet cord. The instructions for installation of the WAP include connecting it to my router for the set up but the installation disk says it is not recognizing the WAP. I use Brighthouse for my ISP and the connection sequence is BH Modem to teh Cisco 871W -- the 871W directly connects to my CPU and to a Net gear FS105 fast network Switch -- the swicth connects to my VOIP phone , HP printer and external HD back-up system -- there is an open port onthe FS105 and two open LAN ports on the 871W.
I tried to install the WAP but connecting it to both the router and the swtich without luck. Is the WAP what I need to connect the Blu-Ray --- am i missing something in the set up?
View 3 Replies
View Related
Apr 30, 2007
I have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???
View 2 Replies
View Related
Aug 25, 2012
I have internet over LAN with Motorola SB5102 broadband modem. Is it possible to share this internet on Edimax EW-7416APn V2 access point?
View 1 Replies
View Related
Dec 20, 2012
Just bought a new router and repeater for a wifi hotspot i am currently running.. I thought i was havng problems with the repeater after i change from router to a server, (and i'm now using a router in bridge mode) so the server is managing all the dhcp.. etc, Hence, the router is Running as an access point. The server which is a Hotspot Server does the rest. For some reason, repeaters, do connect to the access point apparently, but when connecting the client to the repeater (instead of access point) I can't get internet access. although i do get access to the repeater setup.and access point setup too.. or if that is the fact that repeaters must be connected to a router, not access point? should I use it as a WDS? or AP-wds? I have a Cisco Lynksys e1200 router (which i'm using as access point) and an Encore ENXWI-1AN45 3 in one range extender?
View 2 Replies
View Related
Jan 24, 2013
I have a 2wire wireless router and I would like to connect the e1000 in another room as a AP(access point).
View 2 Replies
View Related
Mar 1, 2011
I have just had built a custom system and I purchased a new Canon Pixma 5220. I have the printer recognizing the access point, but it will not connect to the access point.
View 1 Replies
View Related
Aug 10, 2012
I am having trouble connecting the Amped Wireless AP600EX access point to my WRSV4400n. As soon as I plug the range extender into the router, instead of it receiving an IP address, it crashes the router. I have updated the router firmware to 2.021. I have checked the box in the WDS menu to "allow wireles signal to be repeated". I will check with Amped, but are there any known issues between this router and the Amped Wireless family of range extenders?
View 1 Replies
View Related
Dec 5, 2011
I have a E2500 router and 3 WAP610N access points. Users are having a difficult time connecting to the AP's. The client device just sits there trying to obtain an IP and then times out. If they get within range of the actual wireless router, then connect instantly. Is there a setting to increase that will allow longer time trying to obtain an IP?
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap. See diagram below. Not sure if this has some impact?
View 4 Replies
View Related
Mar 4, 2013
I am having trouble connecting my device to certain WiFi networks. We work with hotels and we have a handful of devices that are just not able to connect to their network. Te device works fine in my office. When I get to the Setup page and do a site survey, it'll get to 100% and then display a "page can't be found" as oppose to showing me that it has been connected. We had the MAC address cleared in their network and still no luck. Firmware has also been updated.
View 7 Replies
View Related
Nov 8, 2006
,I was having problems connecting to a network that is TKIP secured with a WMP11 Wireless PC card. I'm wondering if this is possible.
View 9 Replies
View Related
Jul 15, 2012
Not able to register AP Point < Air-Cap35021-E-K9 > on 4402 WLC running IOS (AIR-WLC4400-K9-7-0-235-0 ) Other AP already registered on the WLC are AIR-LAP1242AG-E-K9 & AIR-LAP1131AG-E-K9.
View 13 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Jun 30, 2010
We Have a WLC-4402 controller with LWAPPs and different VLANs and SSIDs. I've configured a Linksys WET200 to associate to one of the SSIDs.On the WLC I can see, that the WET200 is associated to one Wlan.Then I connect one computer with a static IP address and works fine.But when I connect a second one, everythiing goes down. It does not connect.I can only connect one computer to the WET200.Do I need other seetings on the WLC to allow pass traffic through the WET200?
View 4 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Mar 16, 2013
configuration of a 1310 that will be a root access point and connected to wlc 4402. The AP will be implemented as autonomous and not lightweight.
View 3 Replies
View Related
Jun 18, 2011
We have a controlled setup comprising of a 4402 WLC in our Data Centre and 1242AG LWAPs in our branches.The Wireless works well with a mixture of locally switched (h-reap) and centrally switched WLANs.I have a problem where Android devices don't seem to function as they should.I have been using an Android phone (HTC Desire, currently running 2.3.4 OS, but has been a persistant issue since 2.1) and it connects to my home wireless (and others) fine, but when connecting to the Wireless LAN at the office, it connects fine and gets assigned an IP address, but NO data flows. None, like there is no connection at all. I have just been using it on 3G. I figured it might have just been an issue with the hardware, so didn't bother too much.I have just purchase a new tablet (ASUS Transformer, Currently running 3.1 OS) and this does the same thing.I have tried publishing a new WLAN and have tried all types of encryption and authentication al the way down to open and still, no data flow. I have tried statically setting the IP details and still nothing.Interestingly, When I attended the last Cisco Live conference in Melbourne this year, I had my phone and it displayed the same behaviour on the Cisco supplied wireless, BUT, there was a second IPv6 enabled, when connected to that everything worked fine.
View 2 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
