Cisco 870 / Aeronet 1180 - DHCP Information Not Being Sent To Access Point Clients

Oct 3, 2011

I have a Cisco 870 integrated service router and 3 Cisco Aeronet 1180 Access Points.I have configured the router to act as a DHCP server. with all four /26 subnets in a seperate address pool.the first one is for the routers wireless interface and works fine.but the other 3 are for each of the wireless access points, that are used for internet access, but have to operate independently (i.e. the clients on each must not be able to access anything other than the devices associated with that access point and the internet.

The problem I are having is that the router doesnt distribute DHCP information via the access points so the clients on all the access points are not recieving any internet connection at all, but are connecting to the access points, and the LED for the access points suggest that they are connected t the router, the router accnowledges their existence but is not transmitting through the fast ethernet switch ports. but is communicating with a wired printer that is associated with the wireless vlan.

Each access point is on its own vlan, and the switchport access vlan command has been used. only the five static addresses have been excluded from the address pool. the router, the three access points and the printer adresses are static. the printer is working despite being the only device on the /24 network all other addresses are on the /26 networks. this to my knowledge shouldent work but it does, which is handy because the printer software doent support subnetting.The simulation I have ran say that only the printer shouldent work, but its the access points that are not working how they should. I have studied the configuration of the router and access points, and came up empty on why they are not recieving DHCP information.

I are not even able to telnet to them, despite having an address setup. I have not set up a routing protool on the router due to it being the only router. I have checked the interfaces fa0 to fa3 and they are line up protocol up, the wireless is line up protcol up, the vlans are line up protocol down, except the one asociated with the wireless which is line up protocol up (I believe the protocol only goes up when a device is connected to it).

View 9 Replies


ADVERTISEMENT

Cisco :: Information For Connecting Access Point To WLC 4402

Nov 15, 2011

I need Some information for Connecting  my New Access point ( Cisco AIRLAP 1242AG) with WLC(4402) ControllerIn our network set up we have two WLC(4402) we needs to Connect this New Accesspoint To one of our WLC,My Access point is brand New. I need to Know what all i have to do inorder to connect this AP to the controller (from Acesspoint perspective & WLC perspective),I need to Know  what I need to do in AP to connect to the Controller,Do i need to Assign Static IP Address forAP or after connecting to the switch it automatically gets ip from DHCP and regsiter with controller??

View 38 Replies View Related

Cisco Wireless :: 1130 Information For Guest Wi-Fi For Stand Alone Access Point

Feb 14, 2012

We have an Cisco Aironet 1130AG access point which is deployed as Stand Alone Access point, connected to Cisco 2960 Switch.Now we want to configure an Guest Wifi Access for  guest users , for accessing internet ,Is it possible to configure Guest wifi for stand alone access point,( Bcoz i created in WCS, i am not sure about stand alone), i read  in articles like create new vlan for Guest account & assign it like that , but not clear.

View 7 Replies View Related

Most Wireless Clients Associate To One Access Point?

Feb 23, 2011

most of my wireless clients are associating to one ap when there are ap's closer. do i have some setting configured wrong on my controllers?

View 1 Replies View Related

Linksys Access Point :: Where I Can See Clients Associated To A WAP200E

Nov 7, 2011

Because of a connection problem, I would like to know where I can see the clients associated to a WAP200E AP and the signal level of each client.

View 1 Replies View Related

Cisco :: AP1240 / Clients Cannot Connect To Access Point

Apr 9, 2013

I have a AP1240 Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1), and want to configuration WPA2 without using Radius.But my clients can not connecto to AP. On AP always display messages "%DOT11-7-AUTH_FAILED: Station 0026.6609.e55d Authentication failed"
 
Here is my configuration:
 
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname AC1P1F08

[code]......

View 10 Replies View Related

Cisco Wireless :: WAP321 - Clients Connected To Single Access Point?

Oct 15, 2012

How many wireless clients can connect to a single WAP321 Access Point?            

View 2 Replies View Related

Cisco Wireless :: 1142 - Maximum Recommended Clients Per Access Point?

Jan 24, 2013

We are about to upgrade our training facilities wireless and i have a few questions regarding the number of active clients we should target our design for.
 
We would be using 1142 and 3502I access points. I was thinking that  based on the belo we'd be able to support around 30-40 clients per AP.
 
Protocol
Type of web use
Amount of bandwidth allocated per device

[Code]....

View 4 Replies View Related

Cisco :: Use Access Point 1242 To Do Clients Location Using WLC 5008 / NCS 1.1 / MSE3310

Dec 2, 2012

Can I use the access point 1242 to do clients location using WLC 5008, NCS 1.1 and MSE3310?On this moment I doesn´t need of CleanAir features. I want just to do location for clients and rogue aps.

View 2 Replies View Related

Cisco Wireless :: Any Way To Get Information About Clients Connected To AP WAP200

Mar 16, 2013

is any way to get information about clients connected to an AP WAP200?

View 2 Replies View Related

Cisco Wireless :: WCS 7.0 - Monitor Clients Displaying Wrong Information?

Jan 30, 2011

I've been having some problems with the Monitor Clients menu on a WCS 7.0 server, for instance if I go there and display the detected clients on the last 24 hours I get a different set of clients than if I go and generate a report of unique clients for the last day on the report menu. Is this normal?, shouldn't both reports get the data from the same place and give the same result?.

View 4 Replies View Related

Cisco Wireless :: DHCP On 1131 Access Point

Jul 21, 2012

I have a static IP given to me by the service provider, and I need to make the Access point as a DHCP server to provide me IPs inside my LAN.I have created a DHCP pool in the AP. But do I have to NAT the public IP onto the private DHCP range ? This setup is possible.

View 12 Replies View Related

Cisco Wireless :: Setting Up 1142 Access Point With DHCP

Aug 10, 2011

I am setting up an autonomous 1142 Access Point. The intended goal is to get it accessible though 2 SSIDs:Private: VLAN3 (our internal data VLAN)Guest: VLAN98 (our DMZ/Segregated VLAN)At present, our VLAN3/internal users get DHCP addresses from x2 Windows DHCP servers. Eventually, the DMZ VLAN connections will get their IP addresses from a switch in our DMZ VLAN.At the moment, I am able to authenticate with the Access Point through the VLAN 3 SSID but never get an IP address. I have posted the switch port config below as well as the Access Point config.

View 2 Replies View Related

Linksys Access Point :: WAP610N - Way To Connect On DHCP?

Dec 9, 2011

I've some strange things with my WAP610.I connect it to my lan, my DHCP server assign an IP, that's normal way..I lookup for this IP, and fill in the address field in my IE (firefox or safari I've tried all of them).... the AP ask me password and user... I fill in the password field... and get into config...

So I think it could be a bug with static IP... I'll try on the wireless security... select "manual"... change nothing (leave default value) click save... wait a while... connect on the DHCP ip, return to the wireless page... and lost a lot of time since nothing is saved.

View 7 Replies View Related

Linksys Access Point :: No IP Via DHCP And No Internet Connection On WAP300N

Mar 17, 2013

To extend my wired ethernet I have purchased a WAP300N access point and connected it according to the instructions. I can see the AP from a wireless client and connect, but no IP number is provided to the client. The AP is connected to a router which has a DHCP server via wired connection (though a switch). The AP does it self get an IP number from the router but does not pass through DHCP requests from the clients.Occasionally an IP number is provided, but then there is no route to the LAN or the WAN on the other side of the AP.I have tried a whole lot of things to make it work (and been in the internet chat for two hours with a Linksys supporter, who could not make it work either).I have tried to set the IP number in the AP to static.I have tried to remove security (has to be WPA2 eventually, but for the sake of testing it has been removed)I have tried to factory resetI have tried to reinstall the firmware (the same version as the factory installed)etc.

View 4 Replies View Related

Linksys Access Point :: WAP610N Unable To Provide Dhcp

Oct 16, 2010

I set up my internet access by adsl modem as gateway, then RV042 as load balancer and dhcp server, security by MAC address restriction and static IP assignment. WAP 610N used as access point.works great for first few weeks, then somehow I can't access the network.I've been using linksys on my SOHO network, no problem before (RV042+WAP54g)

View 9 Replies View Related

Cisco Wireless :: 2500 / 5500 - Wireless Access Point Identification By Clients

Apr 30, 2012

We have recently been given this unusual task.  The setup is a series of CAP3502P access points, and a wireless controller (either 2500 Series or 5500 Series), as well as other standard network infrastructure.
 
In this network, the client (mobile/wireless) devices must be able to detect when they change what access point they are communicating through, while also requiring a seamless transition.  Ie, if the client device is communicating via access point A, and displaying the application menus for A, when the user walks to the area services by access point B, it must detect that sot he application can display menus for B, without the user having to select "B".
 
Is there a way for the client device to detect which access point it is using and provide that to an application? Or alternatively a way for a host service residing on a server to get that information from the wireless controller?

View 2 Replies View Related

Cisco Firewall :: Get DHCP Information From ASA5505 Using SNMP?

Feb 13, 2013

I have a ASA5505 with version 8.4(3) that it's working as a DHCP server and I would like to get information about IPs availables (or assignated) on theirs pools via SNMP but I can't find the MIB or OID that I need.
 
What MIB that I need?

View 1 Replies View Related

Cisco Wireless :: Can Access Point AP541N Connect To Wireless Clients

Aug 10, 2010

Can the access point AP541N connect to wireless clients with 802.11g/a simultaneously?

View 1 Replies View Related

Cisco Switching/Routing :: 881w-gn-a-k9 Access Point Not Serving DHCP Addresses

Jan 27, 2013

i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?

version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption

[code]....

View 13 Replies View Related

Cisco Wireless :: Configuring DHCP Reply-agent On 1142N Access Point

Feb 27, 2012

configuring DHCP on access point, i have cisco 1142N access point, in my network.. working in autonomous mode, i have assigned a static ip to access point with default gateway.. from AP i'm able to reach internet and user connecting to access point are not able to get ip.. i have DHCP server in my network. how to make access point to fetch ip from my dhcp server and assign the saem to client.

View 10 Replies View Related

Linksys Access Point :: WAP610N - WLAN Printer Network / DHCP Server?

Oct 27, 2011

I use the WAP610N as an Accesspoint for only an small Mobilephone to WLAN Printer Network.My big Problem is that i have therefore no DHCP Server in this special small WLAN Network.And now i need an own DHCP Server from the Accesspoint side because otherwise i must use static IP Adresses in all Mobilephones to connect with the WLAN Network .In the WAP610 unfortunately there is only the choose between static IP Adress and IP Adress FROM an existing DHCP server .

View 2 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Cisco :: Aeronet 1250 - Radius Authentication For Wi-Fi Users?

May 20, 2013

I have a aeronet 1250 access point and i have a windows 2003  radius server configured to authenticate users. I need to configure the access point for radius authentication .

View 1 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related

Cisco Wireless :: To Connect Aeronet 1200 As A Bridge To A Linksys E1000

Mar 27, 2013

I need to setup my Aironet 1231 to connect some remote computers to a Cisco home wifi unit wirelessly. Here is what I need:

CiscoLinksys E1000 provides my wireless Internet connection in building A ----> Cisco Airnet 1231 is in building B and cat5 cable cannot be run between the buildings. Building B can see building A's wifi signal but only on one side. I need to provide wifi Internet to the entire B building. ---> Cisco 3550 PoE switch ----> another Areonet 1231 ---> Laptops via wifi.

OR

CiscoLinksys E1000 ----> Cisco Airnet 1231 ---> Wifi PC's

Either setup will work. My goal is to provide Internet access to one or more laptops via wifi. How would you set up the Areonet?

As a: Root bridge, Non-root bridge, or a Workgroup bridge?

View 2 Replies View Related

Cisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point

Apr 20, 2012

I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.

View 4 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Cisco Wireless :: 881-W Wi-Fi Clients Not Getting DHCP?

Mar 8, 2009

I'm monkeying around with an 881-W.  Clients can associate and authenticate to ssid 'test', but they cannot get a DHCP address.  Clients plugged into f 0 - 3 get DHCP addresses just fine. 
 
I've looked at a lot of different guides, ran debugs etc.  When wifi clients make DHCP requests the server never gets them.  So there must be some IRB thing going on.

View 5 Replies View Related

Cisco :: Setting Up DHCP For VPN Clients On ASA 5510?

Jun 30, 2011

I'm trying to understand my options for assigning addresses to VPN clients on an ASA 5510. Under the ASDM, I have a field for DHCP servers, radio buttons: none, dhcp link, dhcp subnet, and field: client address pools. Cisco's VPN examples demonstrate setting up a client address pool, which I did, but the VPN client isn't assigned a gateway in the process so it can't connect to anything; I really don't understand the point of this. I'd like to create a DHCP pool on the ASA for VPN clients as this seems to be the standard configuration. However, I don't know where in the ASDM to configure this and how it's applied. The only DHCP options I found involved creating a DHCP server on an interface, which I don't want to do since VPN users aren't on a physical interface, right?

View 6 Replies View Related

Cisco Wireless :: No IPs From 2504WLC DHCP To Wi-Fi Clients

Mar 29, 2012

I have new 2504 WLC + 1041LAP. I configured the first DHCP scope on WLC and the first WLAN. Then I set WLC DHCP server in WLAN properties and tried to connect to WLAN with wireless clients.
 
My wireless clients are able to authenticate on WLAN, but not able to get IPs from DHCP. The only lease that DHCP shows is for 1041LAP.
 
If I set permanent IPs on my wireless clients, they can connect and ping WLC.

View 4 Replies View Related

Cisco :: WLC 4402 With 6.202 Can't Give Dhcp To Clients

Sep 29, 2011

When on the management interface the clients can't get dhcp but the AP's can on the same vlan.   I've tried enabling and disabling dhcp proxy,  and using a remote dhcp server as well as the internal server.   This same config works on the 4402 we're replacing with version 5.2.193 on it.

View 13 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved