I've been having some problems with the Monitor Clients menu on a WCS 7.0 server, for instance if I go there and display the detected clients on the last 24 hours I get a different set of clients than if I go and generate a report of unique clients for the last day on the report menu. Is this normal?, shouldn't both reports get the data from the same place and give the same result?.
View 4 Repliesis any way to get information about clients connected to an AP WAP200?
View 2 Replies View RelatedSuddenly after more than a year of running fine, my wap seems to be giving all clients a bad DNS suffix which of course breaks DNS resolution internally (no problem with internet resolution). I assume it's a wap problem since all of my wired clients receive the correct suffix. I'm using a RVS4000 router if that makes any difference.
View 2 Replies View RelatedI have installed an SR520 with wireless for a client. They have asked if there is an easy way for them to monitor who is connected to the wireless at any given point in time. They are not capable of using the IOS command line.
View 1 Replies View RelatedI have a network setup as live-ssid. It is using the Interface for VLAN 14. All APs under the default-group AP Group obviously allows clients to DHCP an address from VLAN 14. This is working fine.
I created a new AP Group called 3rd Floor. This has the live-ssid setup, but instead of using the Interface for VLAN 14 it is setup for the Interface for VLAN 50. I have all the APs on this floor moved to the 3rd Floor AP Group.
The problem is that 95% of the clients on 3rd Floor are still picking up DHCP addresses from VLAN 14. I checked and all the clients are connected to the APs on the 3rd Floor. Only 4 Clients are getting an address from VLAN 50.
I'm not sure if something is configured wrong or not since some devices pick up the new VLAN and the rest don't. I've manually reboot the APs on the 3rd floor to see if that would fix it.
I have a Cisco 870 integrated service router and 3 Cisco Aeronet 1180 Access Points.I have configured the router to act as a DHCP server. with all four /26 subnets in a seperate address pool.the first one is for the routers wireless interface and works fine.but the other 3 are for each of the wireless access points, that are used for internet access, but have to operate independently (i.e. the clients on each must not be able to access anything other than the devices associated with that access point and the internet.
The problem I are having is that the router doesnt distribute DHCP information via the access points so the clients on all the access points are not recieving any internet connection at all, but are connecting to the access points, and the LED for the access points suggest that they are connected t the router, the router accnowledges their existence but is not transmitting through the fast ethernet switch ports. but is communicating with a wired printer that is associated with the wireless vlan.
Each access point is on its own vlan, and the switchport access vlan command has been used. only the five static addresses have been excluded from the address pool. the router, the three access points and the printer adresses are static. the printer is working despite being the only device on the /24 network all other addresses are on the /26 networks. this to my knowledge shouldent work but it does, which is handy because the printer software doent support subnetting.The simulation I have ran say that only the printer shouldent work, but its the access points that are not working how they should. I have studied the configuration of the router and access points, and came up empty on why they are not recieving DHCP information.
I are not even able to telnet to them, despite having an address setup. I have not set up a routing protool on the router due to it being the only router. I have checked the interfaces fa0 to fa3 and they are line up protocol up, the wireless is line up protcol up, the vlans are line up protocol down, except the one asociated with the wireless which is line up protocol up (I believe the protocol only goes up when a device is connected to it).
In my wireless table of who is connected to the wireless network there are 3 different mac addresses displaying when there is only two computers in the house(its not an outsider, it only shows when the other PC turns on), 2 of them have the same computer name but are connected at different IP addresses(192.168.1.101,192.168.1.102). Side Note:[The 2 PCs in the house were bought at the same time and the mac addresses are similar, but the third is different] Now that i have installed ubuntu i can really see what's going on with my ports, i notice that the mac address, that is not similar to my PC and the 'other pc', is poking around at my ports whenever the 'other PC' is turned on.
View 2 Replies View RelatedI moved 1242 access point to my new buliding which i have 5508 wlc and 3500 acess point are working. i connected 1242 ap in network it got registered and download new ios and downlaoded the configuration and working fine. But i open the WLC tha 1242 ap are not visible in ap list.
View 3 Replies View RelatedSo whenever i plug in my computers with an ethernet cord to my router i get an older, different ssid name displayed in local area connections instead of the one being displayed on the wireless network. For one computer it displays the old ssid name 3011, with a 2 right next to it (i think thats because i had another router with the same name), i changed the ssid twice, but when i plug it into the computer it still displays 3011 2. The other computer displays the first newer ssid but not the official one listed on the wireless network. Either way neither of my computers display the name i have as the ssid when plugged into the router with a cord. do i need to do something else so the names match? i reset the router and updated the firmware before writing this, it didnt do anything. i have windows 7 business for both machines.
View 4 Replies View RelatedI have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedWe are using LMS 4.0 with license of 100 Users. We are managing 12 devices till now. But from last two days I am trying to add a device ( i.e. 2811 router) and after adding the device in DCR (Inventry> Device Administration>Add/Import/ Manage Devices) it displays message i.e. devie added succesfully. But this added device is not displayed in Inventry> Device Administration>Add/Import/ Manage Devices.
observation :
1. In managed device list router 2811 is reflecting in Device Type Groups, but not in all devices.
2. New added device is reflecting in Known device list if we generate a report for know device ( under path Reports>Invenrty>Management Status>Known Device List).
I have my device configured, and it has an IP, subnet, etc.I currently have it connected with serial port to my laptop and used PutTy to get into it,
However, despite it having an IP, I cannot use the web browser with it! This is driving me mad. I want to use the web browser and not the CLI for everything. it has a BVI1 IP as well as an Ethernet address.
this message is flashing again and again after 2 sec
IP-EIGRP(default-ip-routing-table:1) neighbour XYZ is not on common subnet for serial0/0 ?
I lost my internet connection icon in windows 7. When connected, the network notification and icon appears at the taskbar and displays how many bar signal the network has and it was working even earlier this afternoon here. I just used my wired connection for a short time and as i stopped using it then i discovered the wireless connection bar signal is lost, all for me to see a ' Round Star' in the bar side of my internet icon. Am connected to the internet but i can't my connection signal and i tried to restore my computer but after i do that i get a dialog say 'The system restore did not completely succesfully because an anti-virus is running on this computer and has prevented it from changing the settings, turn off anti-virus ans try again' but i have no anti-virus program on my PC.
View 5 Replies View RelatedI have a desktop and bought a wireless adapter to hook up to my apartment complex's wireless network through cox. We have had no connection issues for several weeks.Randomly, both IE and Firefox stopped displaying webpages. Firefox displays the message "The connection to the server was reset while the page was loading."Our apartment complex has tech support, so I called him and we went over so many things. The issue, as he says, is that when I do an ipconfig /release, I SHOULD be showing, under my wireless adapter, the ivp4 address as 0.0.0.0. When I do the release, it shows no ivp4 address, period. It shows I have, and am connected to, the internet and the connection. My apartment complex has 5 different wireless connections I can try, and all result in the same problem. I am able to ping google, yahoo, etc, but when I try to ping my apartment complex's wireless connection (their router) it fails.
Uninstalling and reinstalling the wireless adapter and software, system restore, reinstalling windows, restarting the WAN service under services.smc, unchecking ivp6 under my wireless adapter properties. I have tried disabling McAfee and Windows Firewall. I have no idea what else I can do.I also should note that I have 2 computers of the exact same model, and both present this same exact problem when I connect the wireless adapter to it, so it leads me to believe it is something to do either with the adapter or something with the connection from the adapter to the router. (I can connect to the wireless connection but not to the router itself to login to my complex's internet agreement page.)I have Windows 7 32-bit. I was in the process of signing up for Netflix when this happened, and did not download anything.
I have 2 cat3524xl's and a 3550. I recently did something to the IOS that makes the switch not display any output to the console port. Not sure what I did but even doing the reset as instructed in the Cisco docs by holding the mode button foe 2 seconds after boot. I get the flashing green light but still no output. All POST tests pass according to lights so I tried different cables and all baud rates with no change. I hoocked switches back up in lab and can see them in CDP neibors but do not know how to access them from there as they have no IP assigned to them. Remember this is two of them with exact same issue.
View 2 Replies View RelatedI am running LMS 4.1 and have an issue with Inventory: I have a stack of four 3750 switches, but only two of them are showing up in CiscoView. If I right-click - Topology - Device Report ; I see all four switches. The switches are standard 3750 switches and should be included in the Device Packages for CiscoView
Also if I go Reports - Detailed Device ; I see the same two devices show up under Module Information. However when I go to Reports - Device Attributes ; I see all four devices correctly displayed.
I have tried and deleted and added the stack in CiscoPrime, but with same result.
Why aren't the fa ports that i assign to a voice vlan showing up when i issue show vlan?
View 2 Replies View RelatedWhenever I access a file through HTTP, it seems to require that I completely load the file before it will display.
1) For large images, this will result in the whole thing taking some time to load before displaying in its entirety, unlike the usual progressive rendering.
2) For file downloads, this will result in the file being downloaded only after being cached, appearing only when the whole file has finished downloading, unlike the usual process where it can be seen as a progress bar in the browser's download window (for some reason, FTP downloading seems to work normally)
3) For internet streaming video, this means the video will not display until the whole video has been buffered (i.e. will not play until fully loaded)
1) I am on a home network. Other computers (including my old one) do not exhibit similar problems
2) Using Firefox 9.01
3) Win 7 SP1
4) Realtek PCIe GBE controller
I'm configuring a console server for configuring remote devices. This is working well except for the fact that if a target device is in ROMMON mode, the console server refuses to displays the target device console. It does open the connection but the ROMMON prompt is not shown on the console server . This is essential for this device as we will need to use it to reset passwords remotely and thus need to be able to access ROMMON mode from the console server.
Parts used are a 2951 router and a HWIC-8A serial card. Posted my config below:
[code]
Current configuration : 4389 bytes
!
[Code].....
I've got an issue with SNMP and netflow tools. They are displaying different data for the same (sub)interfaces.I've got metroethernet link which connects root A (Cisco 7606, 12.2(18)SXF8) and root B (Cisco 2811, 12.3(11)TS). MPLS is configured on the link (behind root B there is no more MPLS). I'm attaching root configurations (I've ommited parts of config).Interfaces are:
Root A - gi2/6.2144
Root B - fa0/1
I've configured SNMP and netflow on both devices. I'm using two SNMP tools (CA Spectrum and eHealth) and two netflow tools (CA NetQoS Reporter Analyzer and Fluke Networks NetFlow Tracker) to collect the data. SNMP tools show the same info for defined (sub)interface.Netflow tools also show the same info for defined (sub)interface. I'm attaching reports from one SNMP tool and one netflow tool for the same time period.
1. Looking at SNMP tool, it can be seen quite amount of that data in both in and out direction.
2. Looking at netflow tool, it can be seen quite amount of that data in out direction, while in direction shows small amount of data.
I'm aware that Cisco has difficulties with SNMP counters on subinterfaces. I'm also aware that MPLS netflow has its own difficulties.Root B netflow configuration is quite simple as it has just 2 interfaces to configure netflow on (Fa0/0 and Fa0/1). So I would guess SNMP and netflow data should match, but they don't. When you look at SNMP tool reports for roots A and B, it can be seen that traffic volume is practically mirrored.
I have Windows 7 Home Premium on a Dell Inspiron N5010.
I have had this problem for several weeks, and have searched all over to find a solution (tried them all, but none have fixed it). I have a good wireless internet connection, and sometimes I use ethernet. Despite having such connections, my wireless internet icon doesn't change, as it seems to keep getting stuck on the icon which shows a red x over the ethernet image.
It will show the blue loading ring with the bars as it searches for a wireless connection for a little bit, but then it goes to the same, incorrect icon, even though when I put the cursor over the icon it says "Internet Access".
So far, I've tried deleting the Icon Cache and rebooting, as it was suggested that it could be potentially corrupted, but the internet icon stays the same. I have also tried searching for a driver that could be potentially related to the issue and uninstalling it, but it didn't work. The red x went away for a moment, being replaced by a loading blue ring, but then the red x returned (same icon image).
Is there a specific driver for the icon itself? I know I had to uninstall a driver then reboot to get my battery icon back after it mysteriously disappeared. I also have tried deactivating/reactivating my wireless connection by hitting the button, but it doesn't change.
We have 4 x 4xxx WLCs setup in our Core. I just created an AP group in one of WLC and in theory I should see that AP group in the other 3 x WLCs
For some reason, I do not see that AP group appear in other 3 x WLCs. Very much appreciated if someone could point me to the right information or trouble shooting steps.
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
My testing shows packets just dying in the 5520.
I have run into a major issue with an autonomous Cisco 1142AP. We were in the midst of a firmware upgrade when something went wrong and caused the AP to reboot in an error mode. Basically the unit was flashing Blue, amber, red. We unmounted the unit from the wall, connected to the console, and it would now only flash red over and over. We pulled out the cisco guides and performed a factory reset on the unit. This still does not work. and the contents of our flash directory is empty. All we get is a ROMMON AP prompt on the unit. If I issue a set command, I can see the default settings for IP, netmask, etc.
I cannot access the unit via the network, even after setting IP info and matching it up to my laptop. Since I have no network connectivity, I can't TFTP a new IOS file to the unit. I am stumped. How to get the config as if it was out of the box, or an alternate way to TFTP to the unit? [code]Notice the lines in red, I must have typed someting incorrectly.Now once the unit boots after being reset, I cannot even type in the CLI. Someting majorly screwed up here. Can the bootstrap be reinitialized?
WLC-4402-25-K S/W - Primary and Secondary Controllers were running 4.2.130 to begin with. Customer upgraded remotely using NCS - Primary to 4.2.209 and then to 7.0.230 and all that went fine and is in Production.
Then customer upgraded Secondary also using NCS also from 4.2.130 to 4.2.209 in preparation to upgrade to 7.0.230 and he lost contact with the controller. Sent a technician to site to troubleshoot by connecting to Serial Port. Technician #ESCAPED out of the boot sequence and from the BOOT MENU tried to boot the Primary Image and it failed with CRC error on Flash. He then tried to boot the Backup image and had the same problem. He then tried to manually load 7.0.230 - ER (Boot Software) using TFTPD32.EXE and that went fine. He then tried to load 7.0.230 "aes" S/W - The big over 70 MB file and went through most of the file transfer but failed saying:
ERROR: Transfer Failed.
TFTPD32.EXE said something like "Data Packet too Short or some such thing". Sorry did not write down what TFTPD32.EXE said.
Then we thought "may be" a power cycle of the unit is required after the ER Boot Loader Image was loaded. When we did that the unit died. That is - no communication with the Serial Port. We don't think we have any choice other than RMA - Do we?
Customer says he did read and follow this link - especially Table 10-1. {URL}. He said he used NCS to do the Upgrade. I a not familiar with NCS.
I have many 1262N and 1031AG APs. when the client is connected to the AP 1262N the performance is slower than it is connected to AP 1031AG (with more clients) in 2.4GHz.
View 3 Replies View RelatedMy site is thinking of using AP 2600 instead of the trusty AP 3502 since it has better thru put. Any experience on 2600 as we want to ensure stability for our deployment.
View 4 Replies View RelatedWe have 3 5508 WLCs (A, B, & C) and several LAPs (1140, 3500, 3600). The APs learn the controllers IP addresses through DHCP Option 43. When we setup a new site we put the IP address of the controller we want the AP to join first. Lately, I've noticed that regardless of which WLC IP I put first when I setup Option 43 the LAPs are always joining a particular controller.
View 6 Replies View RelatedI'm using a DSL line that changes IP's. I have the E3200 set to auto, but everytime the IP changes, my internet goes down, and I get an ip of 127.0.0.1 on the status page. I then have to renew the ip and reboot. This happens once a day, usually.
View 3 Replies View RelatedI have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.
View 2 Replies View RelatedMy desktop pc is currently wired into myowireless router and my laptop is fully wireless. How do I send data(pictures,music etc) from my laptop to my desktop & vice versa?
View 1 Replies View Related