Cisco :: 3550 Catalyst Not Displaying Fa Ports In Voice VLAN?
Sep 13, 2011Why aren't the fa ports that i assign to a voice vlan showing up when i issue show vlan?
View 2 Replies
ADVERTISEMENT
Cisco Wireless :: Two 1252 On Ports 1 And 2 On Catalyst 3550 Resets
Oct 12, 2012I have two 1252s on ports 1 and 2 off a Catalyst 3550. No other device on the switch except the fiber uplink.
Initially 1252 #2 (on port 2) resets for no reason at no specific time. We did not have a problem with 1252 #1.
The show ver on #2 does indicate that equipment resets due to power. I figured the 3550 is having problems powering two 1252s so had this AP on PWRINJ4 (validated its not drawing power via show power inline).
Today, #2 does not reset. However, now #1, which is the only device using inline power is now resetting. Same thing, reset due to power. Same weird behavior, at no particular time.
I've also have "no cdp enable" out off each port as i understand CDP sometime cause device to not boot up (15w versus 15.4w issue).
Both AP btw are Standalone IOS.
Cisco Switches :: 200 Learn Voice VLAN And CoS / DSCP From Catalyst 2960?
Oct 31, 2012How can I configure Cisco 200 (SG200-08P) to learn Voice VLAN and CoS/DSCP from upstreamCatalyst 2960?
The Cat 2960 is today used together with LLDP-MED to announce config to Aastra IP Telephones. In some cases I need to use a small switch inbetween and plan to use the Cisco SG200-08P for this. However, I would like to avoid manual config of the Cisco 200 switch.
Cisco Switching/Routing :: Catalyst 4505 - Write Extended ACL For Voice VLan
May 14, 2012I am trying to write an extended ACL for the voice vlan.My scenario is the following:I have two PBXs with two Catalyst 4505 L3 switches.The C4505 are connected trough a trunk link.I have a VTP domain configured.
Voice VLANs are Vlan 100 and Vlan 101 with networks 10.2.0.0/16 and 10.4.0.0/16 Voip telephones are communicating between them self and everything is working fine.I want to secure both voice VLANs with an ACL to allow only couple of IPs to administer the phones.The PCs are connected trough a integrated switch via VOIP telephone.Here is the sample configuration of the dhcp pool for the PC VLAN:
ip dhcp pool PCs
network 10.1.0.0 255.255.0.0
default-router 10.1.1.1
dns-server 10.10.10.1
option 43 hex 010a.5369.656d.656e.7300.0000.0204.0000.0064.0000.0000.00ff
I had to implement the 43 hex option because the PCs did not get the ip from the DHCP because of the vendor specific information.The thing that worries me is will the DHCP forward the ACKs for the PCs if I implement this test ACL:
ip access-list extended VLAN100
permit ip 10.2.0.0 0.0.255.255 10.4.0.0 0.0.255.255
permit ip 10.4.0.0 0.0.255.255 10.2.0.0 0.0.255.255
permit ip 192.168.2.0 0.0.0.255 10.2.0.0 0.0.255.255
permit ip 192.168.2.0 0.0.0.255 10.4.0.0 0.0.255.255
permit udp host 0.0.0.0 eq bootpc host 255.255.255.255 eq bootps (this I am not sure do I need)
permit udp host 255.255.255.255 eq bootps host 0.0.0.0 eq bootpc (also this)
deny ip any any
I only want to allow the network 192.168.2.0/24 and maybe some other hosts to access the web based http gui to adiminister the IP phones.All PCs are connected trough the VOIP terminals. I do not want to deny the traffic to PCs.
Cisco Switching/Routing :: Manipulating VLAN Quickly On Catalyst 3550
Dec 12, 2011I am attempting to create a mass upgrade server for some of our more standardized equipment since our vender cannot upgrade them pre-shipping for us, we've got to do them on our own. This means using a terribly organized wizard written in what appears to be Java...
I have an aversion to Windows and felt that I could accomplish the same thing using expect scripts and a Gentoo Linux server; now all I need is to set my Cisco 3550 (c3550-ipservicesk9-mz.122-44.SE6.bin) to have each port on it's own VLAN, except for fa0/1 which will be a trunk port to communicate with all ports as well as the server.
Cisco Switching/Routing :: ARP Broadcasts Not Reaching All VLAN Ports On 3550
May 17, 2013ARP broadcasts not reaching all VLAN ports on 3550
Cisco 3550, interface Vlan9
ip address 1.1.1.1 255.255.255.240 secondary
ip address 3.3.3.3 255.255.255.240
[Code].....
Cisco Switching/Routing :: 6509 - 802.1x And Voice VLAN / Enable Dot1x On User's Ports On The Switch
Sep 17, 2012I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
Cisco Switching/Routing :: Does Catalyst 3550 Support Inter Vlan Routing
Jul 24, 2007Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedCisco Switching/Routing :: 3550 QOS For Voice Over IP
Oct 25, 2011We're looking at implementing a new phone system which will use voice over ip. Currently we have a mixture of Cisco 3750 and Cisco 3550 switches which don't support power over ethernet. Its been suggested we could continue using the current switches and power the new phones using power adapters.
Int terms of implementing qos (we don't have any at the moment) for the voice will a Cisco 3550 be OK and will having a mixture of different models using 3550 and 3750 pose any challenges with the qos policy for the voice. I believe there are differences in that the Cisco 3550 doesn't support srr-queues but having little experience with qos I'm not sure what impact this will have if any?
Cisco WAN :: 3550 - Voice Quality Through MPLS Over GRE Tunnel
Nov 4, 2011I am facing Voice Quality issue in Cisco Ip phone. However I don’t have any issue while calling between extension in the same Site. I am facing voice quality issue while traffic flowing through the MPLS over GRE tunnel. Its working fine If I am removing the mls Qos in Cisco 3550 Interface.
[Code]....
Cisco Switches :: SF300-24P / Configure Vlan 10 For Data And Vlan 20 For Voice On The Same Port?
May 12, 2011We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies View RelatedCisco :: Switchport Voice Vlan Command Not Putting Port In VLAN?
Feb 2, 2011I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies View RelatedCisco Switching/Routing :: Catalyst 3650 Doesn't Pass Voice?
May 22, 2013|_voip PBX___|-----|__3650___|------fiber-------------|__3650_____|------|_voipphone__| I have a case where voipphone is registered on the voippbx but peaple on both end can't hear each other . No ACL on both 3650 , no firewalls between them , distance is about 2 miles . I tried to make telnet x.x.x.x 1720 or 1719 or 1721 (h323 ports) to opposite switch -connection refused . How can test if ports are open on the 3650 ? Is it coorect If I create allowing acl and apply it on both 3650 on the interfaces connected one switch to voippbx "IN" , second switch on the interf connected to voipphone "IN" ?
View 3 Replies View RelatedCisco WAN :: Catalyst 3550 Switch Routed Interface
Feb 21, 2011we are using the catalyst 3550 L3 for BGP routing. For e.g. Gi 0/4 is our internal interface tha we want "switch".
We need on Gi 0/5 the same network that is on gi 0/4.
How is it possible? Make it like a 2 port mini switch. Or make a bridge of these 2 interfaces without any complicated reconfiguration needed?
Cisco Switching/Routing :: Catalyst 3550 PoE 802.3af Compliance?
Jan 5, 2012confirm whether the Catalyst 3550 with IOS Rel. 12.2(44)SE is compliant with POE IEEE 802.3af? I see some conflicting informaiton on Cisco's web site. Before Release 12.1(22)EA2, Catalyst 3550 PoE-capable switches (without intelligent power management support) caused high-power powered devices that supported intelligent power management to operate in low-power mode. Devices in low-power mode are not fully functional.
IEEE 802.3af—The major features of this standard are powered-device discovery, power administration, disconnect detection, and optional powered-device power classification. For more information, see the standard.
Cisco Firewall :: Ports To Be Opened Up For Hosted Voice Access On ASA 5515X
Sep 23, 2012I have a customer who is going to host a VOICE services like providing SIP services to its customers. What specific ports required to be opened up for this on ASA 5515X. I would rate it ASAP.
View 3 Replies View RelatedCisco WAN :: Routing Between Routed Ports On A 3550 Switch
Aug 24, 2011I have 2 3550's connected across a wireless link. [code] However, from Switch A, I cannot reach 10.1.3.9Can this 3550 not route traffic between 2 routed ports?
View 8 Replies View RelatedCisco Switching/Routing :: Catalyst 3550 Switch - Dynamic QoS Setup
Mar 28, 2012I live in a condo building that uses 3 Cisco Catalyst 3550 switches connected to a Comcast router with 100 Mbps download. Currently we regulate bandwidth by providing each user with 3 Mbps download. Even if only two people are active they still only get 3 Mbps download. I would like to set it up so if two people are using they each get 50 Mbps; a sort of 'dynamic qos. Is this possible with these switches? Would we have to purchase a Cisco router in order to provide this feature?
View 9 Replies View RelatedCisco Switching/Routing :: Catalyst 3550 With WS-G5482 Gigabit Adapter
Oct 25, 2011I can assign IP addresses to any of the 24 FastEthernet ports (it is a 24 port switch!). However, I have fitted the WS-G5482 Gigabit adaptor to give me Gig ethernet capability. It does not seem to be possible to assign an IP address to the adaptor.I realise that as it is an 'add on module' (well, a plug in module) this is different to the 24 port in the 'body' of the switch. I also have read that these Gig adaptors will only connect to other Gig adaptors (I found that out by trial and error, and then confirmed it by searching here).it's not possible to assign an IP addy to one of the plug in modules; it is not a big deal but I am planning to assign some IP addresses for remote management etc. I was going to use the Gig port for this but it may not be possible.
AH PS I am using the switch and connecting to the internet via the Gig adaptor, then out from one of the fastethernet ports to another little switch and then on to a router and out to the internet, so the switch and the plug in module are working fine.
Cisco Switching/Routing :: Catalyst 3550 / IOS Naming Format Conversion
Jun 11, 2012correlates the older IOS format naming compared with the newer? I have an older catalyst 3550 that might need an IOS upgrade due to us starting to implement dot1x. The reason that I say this is that some of the commands in the dot1x config guide, such as aaa accounting dot1x, are not valid on this platform. The current IOS is c3550-i5q3l2-mz.121-8.EA1c but the newer format is the ipbase, ipservices, etc. format. There is a newer ios but how do I convert from one to the other? I think I need to research the IOS to see if the new commands are there as well as I want to make sure there are no gotchas from a hardware standpoint if I upgrade.
Cisco Internetwork Operating System Software IOS (tm) C3550 Software (C3550-I5Q3L2-M), Version 12.1(8)EA1c, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2002 by cisco Systems, Inc.Compiled Fri 15-Feb-02 10:50 by antoninoImage text-base: 0x00003000, data-base: 0x006675E0
ROM: Bootstrap program is C3550 boot loader
ACSTMElab-3550 uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c3550-i5q3l2-mz.121-8.EA1c/c3550-i5q3l2-mz.121-8.EA1c.bin"
cisco WS-C3550-24 (PowerPC) processor (revision C0) with 65526K/8192K bytes of memory.Processor board ID CHK0615V0BPLast reset from warm-resetBridging software.Running Layer2/3 Switching Image
[code]....
Cisco Switching/Routing :: Catalyst 3550 Screen Not Allow To Enter Telnet
Mar 7, 2013I have a catalyst 3550 and will be using it to run my cisco 7940 and 7960 ip phones with POE. When I plug the phones into the switch they power up just fine but the phones will not dial out as they have little x's by the line. I have also tried going through the set up of the 3550 but get stuck in one place. When I go to the 10.0.0.0, the screen will not allow me to enter the telnet page or allow me to enter any information. In the manual it shows a pic of what the screen should look like when I go to 10.0.0.1, but I am getting an entirely different page.
What I need to do to get everything set up correctly?
Cisco Switches :: Voice VLAN Implementation On SGE2000P
Sep 17, 2011I'm planning to separate voice and data traffic with two vlans. I have a COR switch catalyst 3750, a UC560 for VOIP with SIP trunk and SGE2000P as access switches. The thing is i had configured VLAN1 (data vlan) and VLAN8 (voice vlan), i've created the vlan 8 in the database on 3750 and let pass those vlans through a TRUNK port. In the SGE2000P configuration i've created the VLAN8 and the the ports as trunk for letting pass the two vlans for the PC and the IP phone. This works but some phones aren't registering, and for example i've unplugged a register phone and plug and doesn't registering anymore.
View 0 Replies View RelatedCisco Switches :: SG-300 Haven’t Set Up A VLAN For Voice From Scratch
Sep 13, 2011We are about to install a new VoIP system (Allworx, which I did not select) and need to set up a new VLAN with QOS quickly for my SG 300 and SG 200 switches. I have the default VLAN1 at 10.0.0.0/24 and will be setting up VLAN10 at 10.1.0.0/24 for voice. There are a few other VLANS on the switches as well. I really don’t get the particulars of using a Voice VLAN vs. Smartport, but is one better than the other for this and what would be some good default settings to start with. I have command line and VLAN experience; I just haven’t set up a VLAN for voice from scratch.
View 1 Replies View RelatedCisco WAN :: 3550 - Blinking Green / Amber Lights On Ports?
Jul 11, 2011I am replacing an old Catalyst 3550 (that has 2 Gig ports) with a 3750 (that has 4)- I used the exact same configuration in the new switch. When I plugged in the new 3750, the trunk ports started blinking from green to amber. I dont know why this is occuring- it SEEMS to be fine, but we havent thrown a whole bunch of traffic over it.
View 4 Replies View RelatedCisco Switching/Routing :: 3550 - Set Up With 6 VLans And 2 Trunk Ports?
Oct 9, 2012I have a test switch (Cisco 3550) that I want to set up with 6 Vlans and 2 trunk ports. I want to be able to access a virtual server conected to the trunk ports from the switch ports. Ports Fa0/1 to 8 are in a vlan port fa0/9 to 16 another vlan etc. Ports Fa0/47 and 48 are the trunk ports. This is a lab environment so the the switch is the only device being used.
View 4 Replies View RelatedCisco Switches :: SG300 / 6941 Phone Not On Voice Vlan?
Jul 25, 2012I am having a problem with 6941 phones on a SG300.When connected Smartport assignes the native and tagged voice vlan correctly, however the phone connects to the native vlan. After running a few tests I have found it only happens when the voice vlan is also the default vlan, though this has only been tested with the default left as VL1.I can get to the phone on the native vlan, it picks up an address via dhcp, and the Operational VLAN ID is shown as 4095.Manually configuring the port as a trunk with the native and tagged voice vlans gives the same result.CDP properties for the ports show the voice vlan as correctly advertised.This happens on multiple phones/ports.The 7962 phones on the same switch work as expected.If I set the voice vlan to be something other than the default vlan 1, a vlan with dhcp available, the phone uses the configured, tagged vlan as expected and the Operational vlan shown on the phone is correct.The switch is running 1.2.7.76 I have a test setup with a number of 7900 and 6900 series phones running on a SF300 and have tested all phones as working if the voice vlan is not on the default. I intend to test with the voice vlan as the default shortly to confirm it is not an issue with the specific switch and discover if it occurs on more than just the 6941.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.2 Failed Authenticate With Same Voice And Data Vlan
Apr 14, 2011I have a question its posible to authenticate an cisco phone and PC with the same vlan(voice and data)when i do this configuratión , the phone and pc dont work. The phone display registering and never finished.interface FastEthernet0/5 switchport mode access switchport voice vlan 1 authentication event fail action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication host-mode multi-domain authentication port-control auto authentication periodic authentication violation protect mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfastend.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: WS-C4510R Critical Voice Vlan Support
Dec 15, 2011Critical voice vlan feature, used to place a newly authenticating phone when radius server is dead into appropriate voice vlan, seems to be a new feature and I find the documentation to be incomplete. Do the following switches support this feature in any IoS versions? WS-C4510R, 4506, 3560, 3550,2960s.
View 1 Replies View RelatedCisco Switching/Routing :: Voice Vlan In 3524 Switch With IOS 12.0(5)XU?
Dec 4, 2011I'm using CISCO 3524 switch as access switch and trying to enable voice vlan in fast eth ports as below.
L3 vlans are created in core switches which is cisco 6509
vlan 1 - data vlan
vlan 2 - voice vlan
in cisco 3524
[code]....
if i use the above configs, the phone which is connected to interface fa0/1 is not taking ip from dhcp server. even it didn't work with static configs.while troubelshooting, i have configured as below and it's started working..
int fa0/1
switchport acces vlan 2
speed 100
duplex full.
in this case i can't use this port for data connectivity where as it's required for data too.
Cisco Switches :: SG300 - 6941 Phone Not On Voice Vlan
Dec 10, 2012I am having a problem with 6941 phones on a SG300.
When connected Smartport assignes the native and tagged voice vlan correctly, however the phone connects to the native vlan. After running a few tests I have found it only happens when the voice vlan is also the default vlan, though this has only been tested with the default left as VL1.
I can get to the phone on the native vlan, it picks up an address via dhcp, and the Operational VLAN ID is shown as 4095.Manually configuring the port as a trunk with the native and tagged voice vlans gives the same result.
CDP properties for the ports show the voice vlan as correctly advertised.This happens on multiple phones/ports.The 7962 phones on the same switch work as expected.
If I set the voice vlan to be something other than the default vlan 1, a vlan with dhcp available, the phone uses the configured, tagged vlan as expected and the Operational vlan shown on the phone is correct.
The switch is running 1.2.7.76 I have a test setup with a number of 7900 and 6900 series phones running on a SF300 and have tested all phones as working if the voice vlan is not on the default. I intend to test with the voice vlan as the default shortly to confirm it is not an issue with the specific switch and discover if it occurs on more than just the 6941.
Cisco Switching/Routing :: IP Phone 6921 Voice Vlan?
Apr 9, 2012I have CME on Router 2800 series, and switch 2960 PoE connected to this router.On 2960 switch, there is existing 7945 IP Phone that already work properly and get IP 14.x.x.x from voice vlan 2.
Problem is when I add cisco 6921 IP Phone connect to 2960 switch, it get data vlan 10.x.x.x, not voice Vlan 14.x.x.x I have check CDP and it use CDP v2
Config on 2960:
interface GigabitEthernet1/0/34 <--- this is connected to IP Phone 7945
switchport mode access
switchport voice vlan 2
spanning-tree portfast
[code]....
With same config and condition on port 2960, why the IP Phone 6921 can't get voice vlan 14.x.x.x, whereas IP Phone 7945 can get voice vlan 14.x.x.x
Cisco Switching/Routing :: 3524xL - Switchport Voice VLan
Nov 10, 2012I have encountered a different issue. When I configure " switchport voice vlan 2" under f0/2 connected to ip phone, it does not have any effect.
Below is my set up:
Sw is cisco cat 3524 XL.
ip phone-------f0/2( vlan1)-----SW----f0/1---trunk------f0/0-CME-router+dhcp
|
f0/3( vlan2)
tftp server ( 201.201.201.3)
switch has two vlans:
vlan1 (data) 200.200.200.0/24
vlan 2 (voice) 201.201.201.0/24
Switch management int vlan 1 : 200.200.200.3
router
f0/0.1 200.200.200.1
f0/0.2 201.201.201.1
The trunk is working correctly. (code)
Cisco Switching/Routing :: 3550 - Shut Down Ports Not In Use For Specified Time Frame
Aug 24, 2009Is there a way to configure a switch (3550, 3560,3750) to disable a switch port if it has not been used for a specified time period such as weeks or months. Say you want the switch to disable switch ports that have been "abandoned".
View 8 Replies View Related
