Is there a way to configure a switch (3550, 3560,3750) to disable a switch port if it has not been used for a specified time period such as weeks or months. Say you want the switch to disable switch ports that have been "abandoned".
View 8 RepliesI have cisco catalyst 2960S switch. In this switch I have created the vlan 10 with member ports Gig 1/0/1, Gig 1/0/2 and Gig 1/0/3. What I want to configure is as follows.
- If any one of the port of this vlan 10 is turned down, then I want to shutdown entire van
- If Gi1/0/1 is turned down, then I want to shut down Gi1/0/2.
we're upgrading over 40 of our 3550/3560 switches to the 3560x platform - what I have noticed is that we get quite a few PoE issues when migrating the site - for instance, 90 - 95% of the site's Cisco's phones will come up but not all of them - the best way to resolve that issue is to identify the ports that haven't came up and then shut - wait 10 secs and no shut.
View 9 Replies View RelatedI have a test switch (Cisco 3550) that I want to set up with 6 Vlans and 2 trunk ports. I want to be able to access a virtual server conected to the trunk ports from the switch ports. Ports Fa0/1 to 8 are in a vlan port fa0/9 to 16 another vlan etc. Ports Fa0/47 and 48 are the trunk ports. This is a lab environment so the the switch is the only device being used.
View 4 Replies View RelatedI have a network with static routes witch I need to convert to OSPF.Never used OSPF, and do not have much experience in routing in general.The netvork is connected via some fiber links, but moastly wireless bridges.I have attached a drawing of how the network is.Routers are 3550, 3560 and 3750s.Each router is on a different physical site.
View 2 Replies View RelatedARP broadcasts not reaching all VLAN ports on 3550
Cisco 3550, interface Vlan9
ip address 1.1.1.1 255.255.255.240 secondary
ip address 3.3.3.3 255.255.255.240
[Code].....
I have an doubt about some port in 2960.He have 2 SFP and 2 Fixed Ethernet. Can I use these 4 ports in the same time? Use 2 Ethernet and the 2 SFP with Fiber?
View 2 Replies View RelatedI know in the past on earlier models of the supervisors that you couldn't use all eight uplink ports(4 on each supervisor) simultaneously when you have two supervisors on the chassis. Is this the same case for the 10Gb uplinks on the supervisor 7-E on the 4500 chassis? I tried doing my research but couldn't find an answer.
View 3 Replies View RelatedI have 2 3550's connected across a wireless link. [code] However, from Switch A, I cannot reach 10.1.3.9Can this 3550 not route traffic between 2 routed ports?
View 8 Replies View RelatedI have an hp wireless printer. everytime i shut down or lose connection, i have to reinstall printer. Why won't it save to my laptop?
View 2 Replies View RelatedI have a stack of five 3750X's connected in a single stack with the stackwise cables. Within this one stack, I created two power stacks, one power stack has 3 switches and the other has two switches. In each of the separate power stacks, one power stack port on a switch shows "shut", so the power stacks are not operating in a full ring. Is there a way to do a "no shut" on those stacks ports that are shut? IOS is 12.2(55)SE1
Here is the configuration -
stack-power stack XXX
stack-power stack YYY
!
stack-power switch 1
stack XXX
stack-power switch 2
[code]...
we plan to implement the SMB Pro AP541 for a guest access solution.is there a lobby ambassador like on the big wireless lan controller?is it possible to sign a guest a time frame - e.g. guest user has only 60 min access to the internetis it possible to enter a lifetime for the guest user - e.g. guest user can only login until 10.10.2010
View 2 Replies View RelatedIs there any shut down proceedure for cisco devices in data center cisco router,switches,firewalls ASA-5580-20,ace-4710 and IPS-4260 devices.
View 4 Replies View RelatedOne of my VLANS on my 3750 gives a status of act/lshut. I've tried no shut commands on the interface to no avail. From my reading it seems like this means the VLAN is active but shut down locally.
View 8 Replies View Relatedknow Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies View RelatedI've had a read through the docs for the 3750 series switches, but nothing that definately says that jumbo frame routing will work on a SVI.One part specifically I'd like clarification on is:The default maximum transmission unit (MTU) size for frames received and sent on all interfaces on the switch or switch stack is 1500 bytes. You can change the MTU size to support switched jumbo frames on all Gigabit Ethernet and 10-Gigabit Ethernet interfaces and to support routed frames on all routed ports. It says supported routed frames on all routed ports, but this in the past has meant physical ports, and not Virtual ones.
View 2 Replies View RelatedI have a pair of N7K's in vPC topology with some FEXs attached. I am looking into enabling Jumbo frame on the N7K as well as the FEX. I understand Jumbo frame is enabled globally by default.
My question is I have some interfaces in a port-channel that I need jumbo frame enabled. Do I enable it at the port-channel interface or at the physical interface ? and is the change disruptive to the network ? I am running NX-OS 6.0.2.
I have a cisco 1811 with 2 isp. i want to shut down an interface when a IP is not responding anymore and to “no shut” when the ip is back online. Here what I make: the interface go shut when 85.14.47.40 not respond but never came up when 85.14.47.40 is back online.
track 100 rtr 99 reachability
delay down 10 up 60
! consider it "down" if down for 10 secs, consider it "up" if up for 60 secs
[Code].....
Lets say i have 2 3750 switches stacked via backend stack cables. Now if a packet needs to go from 1 switch in the stack to second switch in the stack, will it travel via stack cable or do we need to connect both switches via uplink ports (ethernet or sfp). I tried reading datasheet but it no wheres mention the actual frame path between switches in stack.
View 3 Replies View Relatedour C3750 like the one described here [URL]
We have the port on the switch set like this:
switchport port-security maximum 25
switchport port-security
switchport port-security aging time 2
switchport port-security violation restrict
switchport port-security aging type inactivity
In case a device connected to the port is inactive for more than 2 minues ( aging time ) the first frame/packet the device generates arrives to the port on the switch, but the switch does not forward it to the appropriate port ( discards it or whatever ).
So far I tested on
1 30 WS-C3750E-24PD 15.0(2)SE2 C3750E-IPBASEK9-M
2 30 WS-C3750E-24PD 15.0(2)SE2 C3750E-IPBASEK9-M
3 52 WS-C3750G-48PS 15.0(2)SE2 C3750-IPBASEK9-M
[Code].....
When we remove port security from the port, it works perfectly fine, as expected.
It seems this is not HW or IOS version related. It seems it is not a stack synchronization issue, it does not matter if a device is connected to the first or other stack member. I tested on C3560 too, here there are no problems, so seems it is 3750 related.
I have catalyst 3750 I want to controle traffics on every port I have tried Frame-Relay Traffice shaping and Quality of service but there is no support for these commands in the switch.do we have any way to limit traffic on every port in catalyst 3750 and 2960 switches ?
View 4 Replies View RelatedI want to enable jumbo frame con a Catalyst 4500, specifically in the WS-X4648-RJ45-E card. (running this IOS version Version 12.2(53)SG1).
For what I checked, this are the only needed commands:
vlan xxx
mtu 9000
interface port 4
mtu 9000
exit
I want to be sure that these are the only needed comands and that they won t generate any disruption.
I need to get some low volume, interactive data, prioritized on frame relay PVCs across our network. I have followed the CBWFQ examples from cisco.com, but my test packets are still showing latency over 1 second. My lab set up has a corporate connected gateway router linked via FE to testrouter 50. TR51 has a T1 frame relay loop to another router acting as a frame relay switch. The other side of the FR switch has a 56k link to testrouter51. I am sourcing test pings from my desktop PC, that are marked as AF43, and leave at a rate of 1/second, when the response comes back in time. I am using a Smartbits to generate some default class traffic at a rate of about 56Kbps only in the 'outbound' direction, toward TR51, as this emulates a file copy from corporate to remote sites, that is causing the AF43 traffic to suffer. Here is the relevant config on the TR50 device:
class-map match-all rtu-data
match ip dscp af43
!
policy-map frame-56
class rtu-data
priority percent 20
class network-mgt-data
bandwidth percent 5(code)
I would like to configure Ethernet jumbo frame setting in a C6509E switch with WS-X6548-GE-TX and WS-X6516A-GBIC port modules, and IOS 12.2(33)SXJ1. whether any of these modules can support jumbo ethernet frames up to 9000 per port bases.Also, if none of these modules support port-based jumbo frame MTU then would the switch allow jumbo frames on Ethernet trunks from an access switch (say a C3560)?
View 3 Replies View RelatedI have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....
Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedIs L3 ip routing on by default in 3550s? If so is the "ip routing" command visible in the config file? If no - I assume that one would enable L3 routing with that config command.In general terms are there any IOS devices where ip routing is enabled and one would not see the "ip routing" command in config. I.E. if that command is not visible in the config could you assume there is no L3 capablity in that device?
View 1 Replies View RelatedThe layer 2 switches are connected to layer 3 Switch via trunks, and routing between layer 2 switch ports with configured SVI's on 3550. All working fine. Now I'm trying to configure routing between 2800 and 3550, I tried connecting both Straight Throught and Crossover cables to the 2800 Fa0/0 and Fa0/1 ports as well as the switchports on 3550
No switchport commands are configured however, the lights do not go on for both straight through or crossover cables. I tried connecting 1750 routers but same result. My goal is to have all the VLANS routed to the internet with configuring NAT translation the router.
I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
I'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
I have enabled ip routing But I dont have a default route, this is becase we don't have a router on the network.
I've been working with these two Cisco devices in my home off and on for several months now but I just can't take it anymore, I'm about to throw them away and go back to Linksys router.
I have a Cisco 2600 Router with only one Ethernet card in it so I have to trunk from my 3550 Switch to that device. I'd like to have my ISP and all users plug into switch and all trunk back to the router's sub interfaces. Currently, I have started over...again, and am unable to simply get the router and switch to ping each other if I put sub-interfaces on the router. See my configs:
2600 ROUTER:
Router#sho run
Building configuration...
Current configuration : 555 bytes
[code]......
3550 SWITCH:
Switch#sho run
Building configuration...
Current configuration : 2302 bytes
!
version 12.2
[code]..........
Port F0/24 is in VLAN 1, as are all ports but Port F0/1 which is my desktop PC. I mocked it up in Packet Tracer and it works just fine. This is just a simple setup and I'm making sure I can ping between switch and router before I move to each next step.
Network is 10.254.0.0/16
snag.gy/3Y8aN.jpg This is the network image.
This is my subnetted connections: http:[url]....
I can ping R2 to R5 but not R5 to R2. I have spent about 10 hours going through my network and code to no avail. I think it is the frame relay that's causing the error but not sure.. I just checked and I think R6 and R5 are not getting their OSPF updates by trying show ip route
Here are my configs: http:[url]....
The situation include 2 cisco routers an 2 switch 3550
so we have Router A in Vlan x access ----->Sw1----Trunk----Sw2<------Vlan y Access Router B I 've to enable rip1 on guys A and B ONLY !!! Avoiding any kind of tunnel I though it was all around fallBAck bridging ... but after days of tries ...