Cisco AAA/Identity/Nac :: ACS 5.2 Failed Authenticate With Same Voice And Data Vlan
Apr 14, 2011
I have a question its posible to authenticate an cisco phone and PC with the same vlan(voice and data)when i do this configuratión , the phone and pc dont work. The phone display registering and never finished.interface FastEthernet0/5 switchport mode access switchport voice vlan 1 authentication event fail action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication host-mode multi-domain authentication port-control auto authentication periodic authentication violation protect mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfastend.
View 1 Replies
ADVERTISEMENT
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Jun 4, 2013
If we configure a Voice and Data VLAn on a switch. And connect EX90 on voice VLAN and PCwith EX90 terminals. Than can we able to share a presentation or data with EX90 or not?
View 3 Replies
View Related
May 16, 2013
im working in a new enviroment and want to makes some design changes to the environment. I wanted to bounce my ideas some of you folks to see if my thinking is on the right path or maybe i could do things better.
Setup:
Currently the setup that i manage includes and Sonic Wall (also dishes out dhcp), HP 1810 "Core Switch" and 3 SG 300-28P cisco managed switches. (all cisco switches tie back into the HP) The router is managed by the isp. There is only one vlan with all traffic going across it.
Obviously the glaring issue here is that voice and data all reside on the same vlan. Correct me if i am thinking incorrectly but the first step would be to create a separate vlan for the phones with its own IP scheme. currently phones are issued addresses from the 150-200 range and everything else is left for pc's, printers etc. To my knowledge the HP switch does layer 3 but i do not know much about it. There are vpn tunnels to remote offices that are used for sharepoint, email and to access other services. Trying to wrap my mind around the environment as a whole so i may be missing something obvious i could do design wise to improve.
View 2 Replies
View Related
Dec 15, 2011
Critical voice vlan feature, used to place a newly authenticating phone when radius server is dead into appropriate voice vlan, seems to be a new feature and I find the documentation to be incomplete. Do the following switches support this feature in any IoS versions? WS-C4510R, 4506, 3560, 3550,2960s.
View 1 Replies
View Related
Apr 11, 2013
I'm trying to use 802.1x to authenticate clients on my network with dynamic VLAN assignment from RADIUS. We have IP-Phones(powered by PoE) that only supports EAP-MD5, and we would rather use MAB(it also uses LLDP-MED for some settings) to authenticate the phones using the MAC-range from the phones vendor. The following scenario works perfect:Connect the phone and let it boot up(takes a while) and authenticate with MAB.Connect a computer in the phones data-port and let it authenticate with 802.1x(or fail and reach guest-vlan) However, the following scenario doesn't work:The computer is already connected to the phoneThe phone is then connected to the switch What happends now is that the computer is authenticated using 802.1x before the phone boots up and get's authenticated with MAB. When the phone is ready, it's authenticated with MAB and everything works. However, after a short period(let's say a minute), using `debug authentication all`, we see a "NEW LL MAC: phones mac" message(which is weird since the mac has already been MAB-authenticated), and then we are unable to contact the phone using ping. When I check `show mac address-table` it has now moved the mac from `Port Gi 0/12` to `Port Drop`. However, if I check `show mab interface Gi 0/12` or `show authentication sessions` it lists the phones-mac as `mab auth sucess `.why the first scenario works, and not the second?
The switch is a 3560E PoE 24p with IOS 12.2.58SE2. Sample of the switch-config: network-policy profile 1voice vlan 90!interface GigabitEthernet0/12switchport mode accessnetwork-policy 1authentication control-direction inauthentication event fail retry 1 action authorize vlan 60authentication event server dead action authorize vlan 60authentication event no-response action authorize vlan 60authentication event server alive action reinitializeauthentication host-mode multi-domainauthentication order mab dot1xauthentication priority mab dot1xauthentication port-control autoauthentication periodicauthentication violation replacemabdot1x pae authenticatordot1x timeout tx-period 5dot1x max-reauth-req 1spanning-tree portfast!Btw, when we tried authenticating the phones using 802.1x too (EAP-MD5), there are NO problems in any of the scenarios. However, we want to use MAB instead of 802.1x to avoid the requirement of configuring the phones with a username and password. The RADIUS response was the same when using 802.1x as it is with MAB for the phones (including device-traffic-class=voice AV-pair).
View 2 Replies
View Related
Feb 2, 2011
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
View 8 Replies
View Related
Oct 13, 2011
I got error message when I convert to certificate authencate via tunnel group.
error message: "certificate validation failure"
client prompte me that "your client certificate will be used for authenticate" but none certificate list popup even i disabled "autpmatic certificate selection" preferences.
some information about my configuration :
ASA 8.2(2)4
Anyconnect VPN 2.5.1025
authentication against aaa is working
some key point:
ASA:
ssl trust-point remote.apac outside
tunnel-group APAC_AnyConnect webvpn-attributes
authentication certificate
View 12 Replies
View Related
Feb 22, 2013
I have installed ACS 5.4 and we are looking to authenticate our Anyconnect users with ACS via Active Directory. I think I have the correct commands in our ASA ( we had ACS 4 and authenticated our anyconnect users ).
I also have configured ACS to use Active Directory and installed the server side cert in ACS. I'm just uncertain how to program ACS to use the security group that I have setup in Active Directory.
View 6 Replies
View Related
Jan 9, 2012
Since CIPC is isntalled in the PC, and PC definitely getting an IP address from the data IP network segment instead of the voice IP network segment, so how to gurantee the following? 1. How the CIPC registered to the CME/CUCM 2. How to gurantee the QoS for the CIPC's voice traffic since the source IP address of the CIPC is belong to the IP network segment?
View 4 Replies
View Related
Sep 7, 2012
I intend to deploy a voice+data network using some old 3745 and 2811. The network in effect has six 3745 in a hybrid topology at different locations and each having three WIC-2T, one WIC-4T, three NMHDV-2E1. That's pretty much juicing out the maximum from these routers These will serve as my core routers and for access I will be using my 2811s with more VWICs and lesser WIC-2T to give voice and data to subscribers. The 2811s will have links to multiple 3745s. The NMHDV-2E1 will serve for the voice needs at the 3745 locations. All the WAN links will be E1. All my telephones will be on analog voice using traditional EPABX with CEPT/ PRI E1 cards for connecting to the routers. And for data, ethernet ports.Two of the routers will have E1 links to the PSTN and Internet which has to be extended to all my folks. Now, for the tricky part, all my network modules are refurbished stuff from ebay and all the ports will have links on them. I intend to use OSPF with only the backbone area.
View 7 Replies
View Related
Feb 13, 2012
I have a question regarding firewall configurations. Is it possible to have two interfaces ( for two internet service providers) one for voice and one for data. Can I have two Outside Interfaces that one will apply to a pppoe client group and the other will apply to a static IP? Is this possible and if so What would be the steps on applying this connection? Also to note I have a point to point connection already established for the pppoe. I also have another point to point connection for data, but however I do not know how to apply this to the firewall.
View 3 Replies
View Related
Apr 12, 2012
I'm struggling with a configuration issue on the Cisco SG200-08P. We are using the Cisco SG200-08P on a mobile cart that will go from class room to class room that will have computer and cisco Voip phone plugged into it. The issue is that each of our closets are in differnt VLANS ( 1 voice and 1 data....lets say data vlan 20 and voice vlan 2025 for conversation) and that we route to each closet.It would be great if I could just create a generic data and voice vlan to dynamically pick up what the upstream switch has however, it seems that I've been unsuccessful in doing so. I can pass the data Vlan no probablem. The upstream switch port is set to access port and a switch port access voice vlan (these are 3750x switches) If the above is not possible I guess I will take what I can get. Should I just create data vlan 20 and voice vlan2025 on the Cisco SG200-08P and make a trunk port on the Cisco SG200-08P and a trunk on the 3750x? Is there an option on the Cisco SG200-08P to tag voice traffic?I'm also concerned with VTP and I did not see an area in the Cisco SG200-08P to set that as a client and transparent mode.
View 6 Replies
View Related
May 24, 2011
How do i terminate a split cat5 for data and voice at the patch panel end?
View 3 Replies
View Related
Dec 11, 2012
I wanted to know about EHWIC 8-Port configuration? We create Data and Voice VLANs and assign 8 ports to the VLANs. So how do VLANS communicate with each other? We cannot make Gi0/1 as sub interfaces and assign the same subnet IP’s as of VLAN IP’s , it wont accept. On 1921 router Assume Gi0/0 we connect to MPLS WAN. What happens to Gi0/1 where do we connect this?
View 1 Replies
View Related
May 24, 2012
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
View 4 Replies
View Related
Apr 8, 2013
I have a customer with several SG300's providing VLAN1 for data and VLAN10 for voice. The PC's are piggy backing off the phones and showing up in the SG300 fine:
One department has recently employed more people so we have an SG200 switch to connect the computers and phones to. I don't seem to be able to get any connectivity between the new switch and the SG300 it is connecting to. I have setup VLAN1 and 10 as per the images below:
View 4 Replies
View Related
Mar 31, 2013
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
View 4 Replies
View Related
Aug 27, 2012
I have a sge2000p to install with a uc520. I have all data traffic passing ok but voice will not work. Phones to not get ip etc.
View 4 Replies
View Related
Feb 5, 2013
We want to use a Cisco 861 Ethernet router to link our LAN's data and voice segments together (each on separate switches). Our switches are not Layer3 so routing over them is not an option. We only use the default VLAN1 on both switches.There is a data segment 192.168.1.0/24 and a voice segment 192.168.150.0/24, each with it's own internet/WAN access (internet for the data lan and SIP provider for the voice lan).
Diagram:
internet-~--router_192.168.1.1------192.168.1.0/24_data_lan--------192.168.1.254_cisco861_192.168.150.254-----192.168.150.0/24_voice------192.168.150.1_router--~-sip_provider
This is want i want to achieve:
- Link the data and voice switches using the 861
- I want to make the Cisco 861 the default gw on both segments, but they should only route traffic destined for the other segment to each other and route all other traffic to their segment's designated internet connection. I don't want the Cisco to do any NATting and there's no need for firewalling either.
View 3 Replies
View Related
May 10, 2013
I have a 3845 edge router connected to the Internet via four T1s and a HWIC-4T1/E1 card. We are adding two more T1s to the mix, and I have a VWIC2-2MFT-T1/E1 card. Here are my questions:
1. Is it correct to state that the VWIC2-2MFT-T1/E1 can support data in addition to voice?
2. I can use the HWIC and VWIC cards together to utilize the 6 T1s together?
3. Do I just add the card, configure the new slot, and add it to the same channel group?
Below is the current config regarding the existing card HWIC:
card type t1 0 0
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
[code]...
View 1 Replies
View Related
Apr 9, 2013
how many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies
View Related
Aug 30, 2012
Having an issue with Macbook authentication. All Macbooks at this one site, on same switch, going to same RADIUS server, work except for one. Looking at logs it appears server and client never exchange certificates. Attached is log for failed Macbook authentication.
View 4 Replies
View Related
May 24, 2011
I think i've got everything set up to authenticate against AD for Tacacs+ device logins. When i check the logs, i see:"24408 User authentication against Active Directory failed since user has entered the wrong password". This leads me to believe that it is checking AD correctly, however if i enter the password correctly for the same AD user, there is no log at all...no pass, no fail.
If i look at the Tacacs debugs on the switch, i see the following:May 25 10:55:07.927 CDT: TAC+: ver=192 id=874699084 received AUTHEN status = ERRORMay 25 10:55:09.932 CDT: TAC+: send abort reason=Unknown
Obviously the switch is communicating to ACS, and ACS is passing info back to the switch. ACS also appears to be communicating effectively with AD since it knows when i put in an incorrect password for the specific user.
View 2 Replies
View Related
Aug 17, 2011
I have a problem with the User Tracking and Data Collection on LMS 4.0.1 . I think It crashes every time or freezes. I Have this error if I lunch UT Acquisition :
Failed to start acquisition: Construction of XML data required for UT IS in progress. Please try After Some Time.When scheduling a CM data collection, I have this error: Data collection IS Already in progress.
I detected an error in ani.log line 12266: Exception in thread "Discovery" java.lang.AbstractMethodError: com. cisco. nm. ani. server. topo. Port Channel.portIfIndex ()
I successfully changed the name of the CiscoWorks server last week with the tool hostnamechange.pl.
Perhaps there was an impact on data collection ?
View 2 Replies
View Related
Aug 20, 2012
we have deployed L3 in-band scenario for wireless 2 years ago and the solution was working without any problem. we have upgrade wireless controller to 5508, since then, when users login to the first page and certified, and they want to browse to the internet, NAC redirects the web page and ask for authenticatin again, despite the users' devices are being shown as certified devices in the list.
View 6 Replies
View Related
Feb 9, 2012
We have remote users that dial-in over ISDN to a Cisco 2911. We have configured AAA to pass the authentication off to a RADIUS server. Once successfully authenticated, the router permits the users to access a single web server. However, we need to do some testing in our test environment, but unfortunately we don't have an ISDN line to test with. We have created a little environment in our LAB using a 2911, a switch, a RADIUS server & web server. I was hoping that we could simply create a "user" VLAN off the back of the 2911 to simulate our remote users, and access the web site from the test usr PC's over the LAN. I was hoping that the 2911 would be able to intercept the connection and pass the authentication off to the RADIUS server (as it does with the PPP ISDN traffic). But I cannot find anyway to do this, because I can only configure AAA to offload either PPP traffic or telnet/ssh connections to the router itself.
In summary what I want is for a user to access an internal web site over a LAN interface of a 2911 - but have the 2911 authenticate the user via a remote RADIUS server first. Is there a way to configure a 2911 (or any router!) to do this?Is the answer to configure port-based authentication (802.1X) on the switch?
View 3 Replies
View Related
Jul 30, 2012
I have setup Cisco Identity Service Engine (1.1.1) with Wireless LAN Controller (7.2.110)Everything is complete unless the URL redirect. My guest client can join the Guest SSID and also can authenticate to ISE.But after they success to authenticate with ISE, the URL in the browser doesn't change to the pre-configure. It still be something like [URL]. Anyway the content in the browser is changed to the URL that being configured such as url...How can I do with this situation cause everything is working fine but only the browser URL that is not change to the preconfigure one.
View 5 Replies
View Related
Jun 3, 2012
Have set up a pair of ACS 5.3 servers and have set up device administration authentication be passed through to an RSA server via RADIUS. All works great.
What we want to do is go a step further and set the system up so that ACS Administrators also have to authenticate to the ACS system by RSA via RADIUS (the same as the Device Authentication we've set up) for ACS administration tasks.
Looking at the options available in the ACS Administration setup (administrator accounts etc) there doesn't seem to be an option to authenticate via another method apart from a local administrator account on the ACS.
Is it possible to do this?
View 1 Replies
View Related
Aug 21, 2012
I have seen couple of people with win7 cannot authenticate to ISE: 12520 EAP-TLS failed SSL/TLS handshake because the client rejected the ISE local-certificate.I've thought of this: Maybe get a 3rd party cert (go daddy) and have that installed in ISE.I know i do have to make a CSR Cert.Sign.Request that matches cn=primary.ise.mydomain, would I also need a cert for secondary?
If I use LEAP as a preferred protocol then it doesn't ask for cert and users are authenticated successfully.I know they have to say do not validate cert and all that but sometimes it doesn't popupt to them they just can't get on.Again maybe going wtih 3rd party certs will make it easier while benefiting from using PEAP?
View 5 Replies
View Related
Jul 12, 2011
On an ASA5520 v7.2 I can only seem to authenticate to the console when using telnet and not ssh. I can connect using both methods, but just have trouble authenticating with ssh. Here are relevent lines related to the issue:
username user1 password ***** encrypted privilege 15username user2 password ***** encrypted privilege 15
aaa authentication telnet console LOCAL
aaa authentication ssh console LOCAL
telnet <my subnet> 255.255.255.0 Inside
ssh <my subnet> 255.255.255.0 Inside
View 2 Replies
View Related
Jun 9, 2011
I have an issue with an implementation, I had a ACS R5.1 that I'm using to authenticate the wireless users with 802.1x, that's OK and working fine. Now I want to use the same ACS to authenticate wired users using MAB (for IP phones, printers, servers, and other devices) and 802.1x (for corporate users). I already configured the authentication services (MAB and 802.1x) on ACS, but when I'm doing tests I can see that for example the phones are trying to authenticate using the 802.1x rules of wireless connection, not using the MAB rules. [code]
You could also see an screen from the ACS in the attached file. On the picture remark you could see a IP Phone trying to authenticate using the wireless Access Services insted of using MAB.
View 1 Replies
View Related
Sep 25, 2011
Having an issue with Cisco ACS v5.1.0.44 and the Cisco WLC 5508. Cannot get users to authenticate and keep getting error messages referring to EAP session timeouts from WLC filling our logs. Seems to be with this model WLC because we have Cisco 4400 WLCs pointing to the same ACS with no issues. Is there a bug or special configuration that is necessary to marry the 5508 with ACS v5.1.0.44?
View 9 Replies
View Related
