Cisco Switching/Routing :: Catalyst 3550 PoE 802.3af Compliance?
Jan 5, 2012
confirm whether the Catalyst 3550 with IOS Rel. 12.2(44)SE is compliant with POE IEEE 802.3af? I see some conflicting informaiton on Cisco's web site. Before Release 12.1(22)EA2, Catalyst 3550 PoE-capable switches (without intelligent power management support) caused high-power powered devices that supported intelligent power management to operate in low-power mode. Devices in low-power mode are not fully functional.
IEEE 802.3af—The major features of this standard are powered-device discovery, power administration, disconnect detection, and optional powered-device power classification. For more information, see the standard.
View 2 Replies
ADVERTISEMENT
Jul 24, 2007
Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies
View Related
Mar 28, 2012
I live in a condo building that uses 3 Cisco Catalyst 3550 switches connected to a Comcast router with 100 Mbps download. Currently we regulate bandwidth by providing each user with 3 Mbps download. Even if only two people are active they still only get 3 Mbps download. I would like to set it up so if two people are using they each get 50 Mbps; a sort of 'dynamic qos. Is this possible with these switches? Would we have to purchase a Cisco router in order to provide this feature?
View 9 Replies
View Related
Oct 25, 2011
I can assign IP addresses to any of the 24 FastEthernet ports (it is a 24 port switch!). However, I have fitted the WS-G5482 Gigabit adaptor to give me Gig ethernet capability. It does not seem to be possible to assign an IP address to the adaptor.I realise that as it is an 'add on module' (well, a plug in module) this is different to the 24 port in the 'body' of the switch. I also have read that these Gig adaptors will only connect to other Gig adaptors (I found that out by trial and error, and then confirmed it by searching here).it's not possible to assign an IP addy to one of the plug in modules; it is not a big deal but I am planning to assign some IP addresses for remote management etc. I was going to use the Gig port for this but it may not be possible.
AH PS I am using the switch and connecting to the internet via the Gig adaptor, then out from one of the fastethernet ports to another little switch and then on to a router and out to the internet, so the switch and the plug in module are working fine.
View 7 Replies
View Related
Dec 12, 2011
I am attempting to create a mass upgrade server for some of our more standardized equipment since our vender cannot upgrade them pre-shipping for us, we've got to do them on our own. This means using a terribly organized wizard written in what appears to be Java...
I have an aversion to Windows and felt that I could accomplish the same thing using expect scripts and a Gentoo Linux server; now all I need is to set my Cisco 3550 (c3550-ipservicesk9-mz.122-44.SE6.bin) to have each port on it's own VLAN, except for fa0/1 which will be a trunk port to communicate with all ports as well as the server.
View 4 Replies
View Related
Jun 11, 2012
correlates the older IOS format naming compared with the newer? I have an older catalyst 3550 that might need an IOS upgrade due to us starting to implement dot1x. The reason that I say this is that some of the commands in the dot1x config guide, such as aaa accounting dot1x, are not valid on this platform. The current IOS is c3550-i5q3l2-mz.121-8.EA1c but the newer format is the ipbase, ipservices, etc. format. There is a newer ios but how do I convert from one to the other? I think I need to research the IOS to see if the new commands are there as well as I want to make sure there are no gotchas from a hardware standpoint if I upgrade.
Cisco Internetwork Operating System Software IOS (tm) C3550 Software (C3550-I5Q3L2-M), Version 12.1(8)EA1c, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2002 by cisco Systems, Inc.Compiled Fri 15-Feb-02 10:50 by antoninoImage text-base: 0x00003000, data-base: 0x006675E0
ROM: Bootstrap program is C3550 boot loader
ACSTMElab-3550 uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c3550-i5q3l2-mz.121-8.EA1c/c3550-i5q3l2-mz.121-8.EA1c.bin"
cisco WS-C3550-24 (PowerPC) processor (revision C0) with 65526K/8192K bytes of memory.Processor board ID CHK0615V0BPLast reset from warm-resetBridging software.Running Layer2/3 Switching Image
[code]....
View 1 Replies
View Related
Mar 7, 2013
I have a catalyst 3550 and will be using it to run my cisco 7940 and 7960 ip phones with POE. When I plug the phones into the switch they power up just fine but the phones will not dial out as they have little x's by the line. I have also tried going through the set up of the 3550 but get stuck in one place. When I go to the 10.0.0.0, the screen will not allow me to enter the telnet page or allow me to enter any information. In the manual it shows a pic of what the screen should look like when I go to 10.0.0.1, but I am getting an entirely different page.
What I need to do to get everything set up correctly?
View 5 Replies
View Related
Feb 24, 2012
I am testing on lab equipment (2 Catalyst 3550 and 1 Catalyst 3560) HSRP version 1 and 2.I successfully created a load balancing between the two Catalyst 3550 on a couple of vlans (11 and 12) on ver 1
now, just adding the command "standby xx version 2" my hosts on the 2 vlans are completely unable to ping the virtual IP def. gw on debugging i checked that msgs are exchangedthe two cat 3550 are seeing each other on HSRP (active / standby roles)the real ip addresses are pingable rebooted the swiches (just as a last resort try)deleted arp chache on hostsremoved the auth on hsrp all of this no effect.
i also tried to modify the priority on the cat 3560 (before he was on both vlans in standby) to make it the active one and with the same config it worked flawlessly.
My only idea is that there is a bug on CATs 3550 (IOS: c3550-ipservicesk9-mz.122-55.SE4.bin) [code]
View 11 Replies
View Related
Aug 21, 2012
I'm trying to turn off SSH version 1 & 2 to pass PCI compliance. Problem is, I cannot touch the VPN link between the two offices. I'm afraid the PKI certificate used for the VPN will be deleted if i zeroize the RSA key which seems to be the only way to stop the router responding on port 22.
Here is the stuff from the running config related to the crypto map:
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
[ code].....
I'm only CCNA so I'm not even sure if the certificate or RSA key is being used for the VPN link, but I can't tell from the running config that zeroizing it would be a good idea and not break the VPN. I'm open to other ways of disabling SSH, as we are able to just connect using a console cable. But it looks like denying port 22 with an access-list doesn't even stop the router from responding to the port.
View 6 Replies
View Related
Feb 21, 2011
we are using the catalyst 3550 L3 for BGP routing. For e.g. Gi 0/4 is our internal interface tha we want "switch".
We need on Gi 0/5 the same network that is on gi 0/4.
How is it possible? Make it like a 2 port mini switch. Or make a bridge of these 2 interfaces without any complicated reconfiguration needed?
View 2 Replies
View Related
Apr 18, 2012
I have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....
View 10 Replies
View Related
Sep 13, 2011
Why aren't the fa ports that i assign to a voice vlan showing up when i issue show vlan?
View 2 Replies
View Related
Oct 12, 2012
I have two 1252s on ports 1 and 2 off a Catalyst 3550. No other device on the switch except the fiber uplink.
Initially 1252 #2 (on port 2) resets for no reason at no specific time. We did not have a problem with 1252 #1.
The show ver on #2 does indicate that equipment resets due to power. I figured the 3550 is having problems powering two 1252s so had this AP on PWRINJ4 (validated its not drawing power via show power inline).
Today, #2 does not reset. However, now #1, which is the only device using inline power is now resetting. Same thing, reset due to power. Same weird behavior, at no particular time.
I've also have "no cdp enable" out off each port as i understand CDP sometime cause device to not boot up (15w versus 15.4w issue).
Both AP btw are Standalone IOS.
View 1 Replies
View Related
Apr 11, 2012
Is L3 ip routing on by default in 3550s? If so is the "ip routing" command visible in the config file? If no - I assume that one would enable L3 routing with that config command.In general terms are there any IOS devices where ip routing is enabled and one would not see the "ip routing" command in config. I.E. if that command is not visible in the config could you assume there is no L3 capablity in that device?
View 1 Replies
View Related
Sep 18, 2012
The layer 2 switches are connected to layer 3 Switch via trunks, and routing between layer 2 switch ports with configured SVI's on 3550. All working fine. Now I'm trying to configure routing between 2800 and 3550, I tried connecting both Straight Throught and Crossover cables to the 2800 Fa0/0 and Fa0/1 ports as well as the switchports on 3550
No switchport commands are configured however, the lights do not go on for both straight through or crossover cables. I tried connecting 1750 routers but same result. My goal is to have all the VLANS routed to the internet with configuring NAT translation the router.
View 2 Replies
View Related
Apr 26, 2012
I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
View 11 Replies
View Related
Mar 10, 2013
I'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
I have enabled ip routing But I dont have a default route, this is becase we don't have a router on the network.
View 18 Replies
View Related
Dec 2, 2011
I've been working with these two Cisco devices in my home off and on for several months now but I just can't take it anymore, I'm about to throw them away and go back to Linksys router.
I have a Cisco 2600 Router with only one Ethernet card in it so I have to trunk from my 3550 Switch to that device. I'd like to have my ISP and all users plug into switch and all trunk back to the router's sub interfaces. Currently, I have started over...again, and am unable to simply get the router and switch to ping each other if I put sub-interfaces on the router. See my configs:
2600 ROUTER:
Router#sho run
Building configuration...
Current configuration : 555 bytes
[code]......
3550 SWITCH:
Switch#sho run
Building configuration...
Current configuration : 2302 bytes
!
version 12.2
[code]..........
Port F0/24 is in VLAN 1, as are all ports but Port F0/1 which is my desktop PC. I mocked it up in Packet Tracer and it works just fine. This is just a simple setup and I'm making sure I can ping between switch and router before I move to each next step.
View 40 Replies
View Related
Jul 24, 2012
The situation include 2 cisco routers an 2 switch 3550
so we have Router A in Vlan x access ----->Sw1----Trunk----Sw2<------Vlan y Access Router B I 've to enable rip1 on guys A and B ONLY !!! Avoiding any kind of tunnel I though it was all around fallBAck bridging ... but after days of tries ...
View 3 Replies
View Related
Oct 25, 2011
We're looking at implementing a new phone system which will use voice over ip. Currently we have a mixture of Cisco 3750 and Cisco 3550 switches which don't support power over ethernet. Its been suggested we could continue using the current switches and power the new phones using power adapters.
Int terms of implementing qos (we don't have any at the moment) for the voice will a Cisco 3550 be OK and will having a mixture of different models using 3550 and 3750 pose any challenges with the qos policy for the voice. I believe there are differences in that the Cisco 3550 doesn't support srr-queues but having little experience with qos I'm not sure what impact this will have if any?
View 1 Replies
View Related
Oct 31, 2011
I am having issues working on my QOS between 4510 and 3550 switch connecting on layer 3 through a service provider. I have class maps and policy map setup on both sides and then policy map attached to interfaces however i dont see any traffic matching in policy map on 3550 switch, i do see some traffic matching on 4510 but the speed with which its increasing has my doubts about it. When i make voip calls ( VOIP switches are sitting behind 3550 and are mainly 3550 pwr 24 port switches with phone ports configured for auto qos voip cisco-phone and trusting cos) i rarely see the RTP matching in class under policy map.
View 5 Replies
View Related
Jan 17, 2013
im trying to install a ios 12.2v on my switch. when the screen prompt it does not show me the user move symbol " SW1> ". all i see is " SW:" and from there i can not enter the commands to download from tftp server !
View 7 Replies
View Related
May 15, 2013
I would like to know how to stack 2 switch cisco 3550 that IOS C3550-ipservicesk9-mz.122-44.SE6
View 3 Replies
View Related
Aug 30, 2012
we have two core swiches 6506 and around 55 cat 3550 switches. currently we are on the process of replacing the cat 3550 switches to 3750 switches.We need 10/1000/1000 speed, ip base image with upgrade options. Our up links from cat 3550s(sfps) are single mode and dual mode fiber mode with 1 gbps ports on core switch.
At present we are not upgrading to 10 gb modules on core. Spread over 15 floors each floor needs 2 up links(single mode , and dual mode). since cat 3750 sfps are smaller in size existing gibics cannot be used. Looking for the best option of cat 3750 switches with 1 gb up links which can be upgraded to 10 gb later when we replace the modle on core. Requirements:
1- Cat 3750 switches 55 in no with sfps for 1 gb up link (dual mode fiber and single mode fiber)
2- stacking option
3- 10/100/1000 speed
4- ip base image upgradable to ip service image
5- ipv6 compatibaility. Network is spread over 15 floors so from each floor we need two sfp up links 1 gbps using dual mode and single mode
-6-Should be upgradable to 10 gb in future when we upgrade the core modules
Or is it better to go for 10 gb module in core as well as edge switches ? if so what should be the modules?
View 13 Replies
View Related
Jun 11, 2008
I have one 3550 switch and i upgraded from 12.1 to 12.2(44)SE . But "tclsh" command is not enabled on this version. As per Cisco, 12.2(25)S is enough to enable TCL interpreter.
View 5 Replies
View Related
Sep 27, 2012
We have a metro Ethernet service, basically our WAN connection, that we use to connect 4 sites. This MOE service has a CIR of 200 Mbps, connected to a port on a 3550-12T running Version 12.1(22)EA5 at 1000 Mbps. We are exceeding our CIR at times during the day for short bursts which is causing the MOE switch to drop packets, which I suspect I am seeing manifest itself in some choppy VoIP conversations and dropped ICMP packets from our network monitoring software. I implemented policy maps to apply an outbound service policy to the interface connected to the MOE service, but I am not seeing any matches to the access lists or the service policy. I’m not sure if I am missing something or perhaps the IOS is not capable?
Below is the config for the service policy and some command output. Notice that there are hits on a statndard access list that is used for other purposes, but the extended access lists used for the class maps have no matches.
!
class-map match-all REALTIME
match access-group name REALTIME
[Code].....
View 4 Replies
View Related
Sep 26, 2012
How do I configuring Private Class A [10.206.90.0/24] and Private Class C [192.168.1.0/24] Network on Cisco 3550-12G Switch.
View 3 Replies
View Related
Aug 3, 2012
I was trying to config qos on 3550 interface
Match protocol is not supported for this interface
So does this mean that qos is not supported on 3550?
View 4 Replies
View Related
Feb 19, 2012
We had re-arranged and purchased new public ips and changed with new modem. Following is the new network setup diag
I have started the configuration, but stucks at a point. Current configurations setup and ip assigment is as follows
ISP modem/router(192.168.3.254)-->(192.168.3.1)1811W Router(192.168.2.254)-->(192.168.2.1)3550(interface vlan 10 - 10.0.1.254, interface vlan 192 - 192.168.1.254)--trunk-->2950
1)Configured 3550 as layer 3 switch and create a default route to 192.168.2.254
2) Configured 2 static routes(for 2 vlan range traffic) and one default route to 192.168.3.254
3) ip pass through is not configured yet, still the public ip is configured at the isp router
1811 static route configs
------------------------------------
Ip route 0.0.0.0 0.0.0.0 192.168.3.254
Ip route 192.168.1.0 255.255.255.0 192.168.2.1
Ip route 10.0.1.0 255.255.255.0 192.168.2.1
3550 static route config
--------------------------------------
Ip route 0.0.0.0 0.0.0.0 192.168.2.254
Testing results 1)All lan communications are working fine(inter vlan also), ping to all servers from router is getting and ping to outside public ips are getting from router,but not getting ping from switch 3550 to 192.168.3.254 and any of the public ips(internet).
View 4 Replies
View Related
Oct 17, 2012
I have an Cisco 3550 48 SMI running IOS (tm) C3550 Software (C3550-I9Q3L2-M), Version 12.1(13)EA1a. Software advisor says that I can only update to Version 12.1(22). The software download area tells me that the latest version is 12.2(44).
know if I could use the latest 12.2? Or has the hardware changed with the IOS versions?
View 6 Replies
View Related
Feb 11, 2013
what I can do to accomplish my end goal of safe public wifi and configuration.I have 2 domain controllers (for redundancy) with a split scope for DHCP and they both serve DNS. I have VLAN 2 (management), VLAN 3 (Servers), VLAN 4 (Wired Access), VLAN 6 (Wireless Access) and VLAN 480 (Outside Wireless). I have setup INT VLANs for all of these on my main router (Cisco 3550) with the ip-helper address to the DC for all but the VLAN 480. All of this works great, and the scopes are setup just like the VLANs. (ie 192.168.2.0 (management) .3 (servers) etc.)I was wondering if there is a way to have VLAN 480 get DHCP from the cisco 3550 as a random address say, 172.16.0.0 255.255.248.0?
On a side note, I have seperate Wireless Access Points for the outside. (From a guy before me) I understand you can have a guest wireless setup on the newer Access Points, and trunk (cisco term) the 2 VLANs and seperate them out with Access Control Lists so they don't talk to each other, but I would rather just give the VLAN 480 it's own DHCP from the router.
View 14 Replies
View Related
Jun 13, 2013
We are trying to replace the CSS between our firewall and DMZ with a BigIP. Among it's other functions, it will act as the router between the firewall and the DMZ. To make this work, I need to assign vlan tags values for the vlans I create on the BigIP box and these must match the tags on the cisco switches (3550's) How do I find this information on the switch?
View 2 Replies
View Related
Oct 30, 2012
I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
View 5 Replies
View Related
