We have 4 x 4xxx WLCs setup in our Core. I just created an AP group in one of WLC and in theory I should see that AP group in the other 3 x WLCs
For some reason, I do not see that AP group appear in other 3 x WLCs. Very much appreciated if someone could point me to the right information or trouble shooting steps.
I read the configuration guide about the 7.3 release. And I figured out that you will need a hash key for establishing a mobility group relation between a controller and a virtual controller. The 7.3 release for the 5500 series works fine for me.But the latest release 7.0.235.0 for the wireless lan controller series 4400 does not have a functionality to add a hash key while creating a new mobility group member.The command "config mobility group member hash" is totally missing. How to establish a mobility group between a 4400 controller and a virtual then ?
View 2 Replies View RelatedI read the configuration guide about the 7.3 release. And I figured out that you will need a hash key for establishing a mobility group relation between a controller and a virtual controller. The 7.3 release for the 5500 series works fine for me.
But the latest release 7.0.235.0 for the wireless lan controller series 4400 does not have a functionality to add a hash key while creating a new mobility group member.
The command "config mobility group member hash" is totally missing.
how to establish a mobility group between a 4400 controller and a virtual then?
I try to map LDAP Group to ASA Group policy following documentation:
[URL]
This is a config for ASA 8.0. I would have expected it to work on 8.4 as well but I do run into problems. The mapping as shown in LDAP Debug and ASA Log will actually happen but it is overwritten by the "GPnoAccess" Group Policy configured locally in the Tunnel Group. From earlier works with RADIUS I would have expected the user specific Attribute to be "stronger"?
ASA Log:
AAA retrieved user specific group policy (correct Policy) for user = XXX
AAA retrieved default group policy (GPnoAccess) for user = XXX
We have a new SSID that needs to be added to an AP through a 4400 Controller with software version
7.0.116.0
All AP's are configured as Lightweight.
I have a 4400 WLC for 100APs running the 7.0.98.0software version. Now, only 48 APs are joined, and the WLC dont accept new joins. The log below are from my WLC but appear for all others APs:
%LOG-6-Q_IND: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%CAPWAP-3-TX_ERR: capwap_ac_sm.c:1966 Failed to transmit discovery response to AP 00:3a:98:ae:e3:f0%CAPWAP-3-ENCODE_ERR: capwap_ac_sm.c:2269 Failed to encode Discovery (code)
My site is thinking of using AP 2600 instead of the trusty AP 3502 since it has better thru put. Any experience on 2600 as we want to ensure stability for our deployment.
View 4 Replies View Relatedis any way to get information about clients connected to an AP WAP200?
View 2 Replies View Relatedi have a existing wireless network setup in my office existing wlc in 4402 and LAPs are 1130 & 1242 all are working fine but we are now planning to use new 5500 series controllers for the same access points,i want to ask that how i can done this job with very minore downtime and users disconnectivity + zero error results??
View 2 Replies View RelatedWe have a WLC4400 controller with about 30 LAP. We moving to a new IP scope and was wondering what is the best way to change the IP address of the controller. We have tried doing this via GUI however we have to power cycle the controller to get it back online using the old ip address.
View 3 Replies View RelatedI want to upgrade all my controllers (a mix of 4400 and 5508) to 7.2.103.0 from 7.0.116.0. Can I make that jump or should I do incremental?
View 7 Replies View RelatedLike the way you do with the Cisco IOS.
ie show start | i router
Does CSCua29504 affect 4400 series WLCs as well? Bug toolkit mentions just 5500, so want to get a confirmation.
View 2 Replies View RelatedI was wondering if there was a way to import a large number of mac addresses into the MAC filtering of a Cisco WLC 4400. We recently purchased 150 new Mac laptops and I need to add them to the Mac filtering. I have 5 WLC's to do this to.I already have the MAC addresses and names in a spreadsheet.
View 3 Replies View RelatedAccording to product bulletin no 3209 for the Cisco 4400 series, the Access Point supports 802.11e WMM.
My question goes to DSCP mapping, according to IEEE and your bulletin the DSCP field in the IP header should be set to 46 (10110 00) for mapping to a 802.11 QoS voice priority 6/7.But my Wireshark trace revealed 4400N is mapping toward with 802.11 QoS is set to Priority 5 Video.
If I google DSCP mapping toward 802.11 QoS all IEEE documention I found says EF /Voice should have 46 or 101xxx in the DSCP IP field but running through Cisco and HP docs gives 46 or 48 as value, that is the correct value. [code]
I posted a few days ago but don't have a good response. I've dig high and low and haven't come across a solution yet. I've been trying to get a customized web Authentication typed. I didn't need a user name or password to get through. All I need is a web pass through and an accept button at the end of the HTML agreement policy or splash page.
I was able to create a log in.HTML and download to the wireless controller, but my problem is how would I get an agree button and when a user click on it and it would redirect to a website. I've followed the following link but no luck. {URL}. the link doesn't tell me weather I should create an accept button manually or is there a setting on the controller that need to check? the link also provide some info. about: Configure Client Machine for Web Pass through, but where should I download the Cisco Aironet Desktop Utility? I've download ACUv502005.exe file for my windows 7 but after the installation it didn't work for me. if you know how to configure the web-pass through. I been working for this for a week now and didn't find the info. that I was looking for.
I have a wireless sytem with a WLC 4400 and several 1522 Access Points. They don't actually function as Access Points because I'm using radio communication only for backhaul. There are no clients connected to the Access Points. All traffic on the network comes from the devices connected on the LANs that are bridged through the APs ethernet port.
I would like to create filters to allow only certain devices to be able to transmit over the radio link. I've used this in the past on 1310 units and it was very easy to do via GUI. This filter could be either by IP or MAC Addresses. IP would be better for me.
I've been having some problems with the Monitor Clients menu on a WCS 7.0 server, for instance if I go there and display the detected clients on the last 24 hours I get a different set of clients than if I go and generate a report of unique clients for the last day on the report menu. Is this normal?, shouldn't both reports get the data from the same place and give the same result?.
View 4 Replies View RelatedMy desktop pc is currently wired into myowireless router and my laptop is fully wireless. How do I send data(pictures,music etc) from my laptop to my desktop & vice versa?
View 1 Replies View RelatedHow do I add the ip information for a wireless system on a acer laptop with Vista.
View 1 Replies View RelatedI have a Cisco Series 4400 WLAN controller and I'm trying to connect a lightweight AP to the controller. I have already assigned the switch port to use my wi-fi VLAN, and have connected the AP to the switch. After a few minutes, the light on the AP goes from green to light blue (indicating it's serving clients). When I log into he wi-fi controller to look for the Ethernet mac address of the new AP, I do not see its Mac Address. I want to be able to rename the AP to reflect where it will be used, but need to select the AP via its Ethernet mac address before I can make any edits like changing its name etc. I've gone through the "monitoring" menu, selected "All" and still do not see it in their via its MAC address. I also will select the "wireless menu" which lists all the AP's on my network, listing in order from on the longest running, to just powered on.Is there something I'm missing like a "re-scan" that scan's all devices?
View 5 Replies View RelatedI have a WLC 4400 with multiple LAP.I have a small area with 30 wireless devices. I want to install 2 APs, to make sure that all wireless devices have a connection to the wireless network and have proper bandwidth. The issue is that the APs will be near each other. Will the APs interfere with each other and will each AP receive an equal amount of connections?
View 3 Replies View RelatedWe use Cisco 4400 Series Controller and Cisco Aironet 1142 Wireless-N Access points andwe use windows 2008 Active Directory and also as our Radius server. We have XP as a client. The Laptops were connecting automatically into the wireless network once they are joined to the domain and adding the laptop to the wireless security group in the AD. All of sudden all the 20 laptops got disconnected from our wireless network.The Laptops can detect our wireless network. But on the system tray the pop says: Windows was unable to log you on to the network MATS. (MATS is our SSID)
View 1 Replies View RelatedI am planning to buy new AP for my existing setup. we are using 1131AG series AP, we need to go for new one with n supported with external antenna.
Current software version on controller is : 7.0.235.3
If already saved the configuration file of a WLC 4400 to a server using TFTP? What is the name of the configuration file?
View 2 Replies View RelatedI'm looking for a document that states the best practices for WLC configurations (Management/Security/AP's..etc). I can currently only find the following document:URL
But this document has last been updated in 2008, in a few days that's almost 5 years ago, and we all know how quickly technology is evolving. 10Gb wireless is around the corner, with 1GB starting to go production now. This document also mentions the 4400 (which is end of life).
Actually we have a 4402 controller with 1120 APs both of which are marked as EoL products, we want to jump over the new 2600 APs and 5508 Controller for increase signal coverage but we have the following deals:Last firmware for 4402 controller is 7.0.Firmware needed for 5508 to support 2600 APs is 7.3.Is it possible to configure mobility between 4402 and 5508 even with different firmware branch?
View 3 Replies View Relatedi'm having some trouble pushing CLI templates to controllers in my lab. i get an invalid credentials error but it is random. sometimes i can push the template fine but 30 seconds later if i push the same template it will fail with error. several minutes later try it again and it fails. i have verified the credentials by reconfiguring them consistantly accrosss the devices but if the credentials were actually wrong it should fail every time, not intermittently. there are also 2 controllers i am testing this against and it is also random which controller fails. on the instances where i don't get the credential error my CLI template fully executes without error.
i am using WCS 7.0.230.0 on WIN2K and two 4400 controllers running 7.0.230.0.both controllers are configured with SNMPv3 and SSH. telnet and lower versions of SNMP are disabled.
I want to upgrade software of the {WISM(Forign controllers 6.0.196) 4400(Anchore controllers 6.0.196) and WCS 5.2.0} to 7.0 code for all,
View 1 Replies View RelatedWe are using Cisco Wireless solution in our network. Using 4400/5500 WLCs and 3500/1130 series APs.
A new requirement has come up and we need to provide connectivity between two buildings (which are within 1 km) using wireless. This link should be able to give >=100Mbps.
As we already have 3500/1130 APs, can a wireless bridge be established using them which can also give >=100Mbps? Can this be done using a WLC based solution? What I mean is: Do I need to have a standalone AP solution or can it be done while both the APs register to WLC? What are the AP models/antennas that can meet my requirement?
on WLC 4400 Guest vlan is configured with local authentication, the users get disconnected after 10mins were should i disable the option of 10mins restriction
View 3 Replies View Relatedi have a controller that has mutliple dhcp scopes and should in theory give out close to a thousand plus addresses. But i have seen wireless users not getting addresses once the controller has leased about 490 ip adds. My controller is on 7.XX version.
View 3 Replies View RelatedI've download a login.html into the controller successfully, but when I preview the page there isn't an accept button. Do I need to create the accept button with the html file or is there some place I need to enable on the controller itself. After download the .tar file I reboot the controller but no luck. I also create a java script button redirect but it didn't redirect to where I needed to go. It just stuck on the splash page.
View 3 Replies View Related