Cisco Wireless :: 4400 - Guest Access Disconnect
Dec 31, 2012on WLC 4400 Guest vlan is configured with local authentication, the users get disconnected after 10mins were should i disable the option of 10mins restriction
View 3 Replies
ADVERTISEMENT
Cisco :: 4400 - Guest Wlan Access To Wlc Management
May 11, 2011I have my wlc 4400 configured with a secure wlan and a guest wlan. The guest wlan is switching traffic at the wlc to a separate guest-wlan interface. When a guest is associated and authenticated, they can access the management console of the wlc which is in a different subnet. As I understand, the wlc does not route traffic. So how could this be happening? the guest subnet and the subnet the wlc management interface is in are different and separated by a firewall. I have also tried applying access lists in the wlc to each interface without luck. How can i stop the wlc from providing access to guest wlan users?
View 3 Replies View RelatedCisco Wireless :: 4400 - Guest Anchor / Foreign Controller Control Path Down?
Aug 16, 2012We have a Cisco 4400 series wireless controller deployed as a Guest Anchor in a private DMZ. We have 13 foreign controllers anchored to this for Guest Wireless. We recently anchored 17 additional controllers to this Anchor controller. Since we have done that, periodically on just 3 of the foreign controllers, the control path shows down on the mobility peer, then comes back up. We have had this issue in the past, but it resolved itself. However, now we are seeing this issue again. Are we reaching a limit on EoIP tunnels? I have read that there is a max of 71, and that is per controller, not SSID. We do have a firewall in the middle but all necessary ports are open.
We have had this issue for quite sometime, it just does not happen frequently. Since we have added the additional controllers, it is now happpening very often, but only with 3 controllers. There is not much in common with these 3 controllers. 2 are 4400 series, and 1 is a 5508. All 3 are local on a campus LAN, different networks. Could it have anything to do with memory or utilization?
Cisco Wireless :: 5508WLC Whitelist For Guest Access And Securing Guest-access?
Aug 18, 2011Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedCisco AAA/Identity/Nac :: LWA Guest Portal ISE And 4400 7.0.x?
Apr 8, 2013Managed to guest LWA working with ISE for wireless guest portal access? I have Cisco 4400 WLCs running latest 7.0 code and ISE 1.1.2.All guest portal examples seem to be CWA which only works on 7.2 code.Am I without hope getting this working on 7.0 code?
View 3 Replies View RelatedCisco :: WLC 4400 And Guest Email Address Capture?
Jul 25, 2010I've got a client with a WLC 4400 series and WCS that wants to setup a public guest wireless access network. They want to have the users put in their email address to authenticate and they want to capture the email addresses to use for marketing campaigns. I know you can setup the login page to have them put in their email address, but i can't remember if you have to use an external web server to actually capture and record the email addresses.
View 7 Replies View RelatedCisco :: Wired Guest Security On 4400 Series WLC?
Sep 27, 2012I have 3 4400 WLC's that implemented at 1 main site within a mobility group. I am looking at implementing wired guest authentication with a splash page for username and password access. I have followed the documents and suggestions about how to configure it. I created a layer 2 vlan (700) and then created a VLAN (151) that wired guests will get an IP address from. I then configured a WLAN with the ingress interface being VLAN 700 and the egress interface being VLAN 151.
All of my controllers are running code 7.0.116.0. When I go to do a test scenario with a wired client, I have the switchport setup for VLAN 151, which they get an IP address from, but when they try to go to the Internet, they don't get the splash page. Why I am not getting a splash page or even if this scenario is possible?
Cisco :: WLC 4400 - Create Guest User Accounts
Jun 13, 2011(WLC 4400) which enables employees to browse to a custom made webpage, where they can create an account for company vistors to access the internet. It's important for the employees not use any login credentials, they arrive on a webpage where they specify the login & password which the vistor will enter to browse the internet. Is there any good link to documention about this topic?
View 3 Replies View RelatedCisco :: Guest Tunnel / Auto-anchor From 2100 To 4400 WLC
Jun 2, 2011We’d like to extend our current Guest LAN from a 4400 WLC in our data center to a 2100 WLC located at a remote facility. However, we cannot get the foreign controller to pass traffic to the anchor controller – or so it seems. The catch is that we’re not actually trying to extend the SSID itself to provide wireless access, but instead flub it so that we can provide local wired access tunneled to the Guest LAN on the anchor WLC. I’m not entirely sure if this is possible, because I’ve read that before the EoIP tunnel will come up a guest client must associate to the foreign WLC.
We’ve followed the instructions we could find that go over setting up this type of scenario, but unfortunately they only cover setting up back-to-back 4400 controllers and as such, some functions described (notably being able to create a Guest LAN) are not possible on the 2100. We haven’t been able to find a clear and concise guide on the scenario we want to set up.
Here’s some detail:
Mobility group is up/up between both WLCs. Both WLCs are running 6.0.x code.
Anchor WLC – 3750G-24WS-S25 (a 4400 WLC w/ integrated 3750G-24)
Guest LAN WLAN “wired-guest” created; Ingress is “none” and Egress is our existing “dirtnet” – i.e. outside access. The “dirtnet” interface is *not* a Guest LAN interface. Mobility anchor is set as local.
Remote WLC – WLC2106
WLAN “wired-guest” created; Interface is “wired” w/ an IP address on the same subnet as the anchor “dirtnet” and associated with port 2. Mobility anchor is set to the anchor WLC and is up/up. I have a laptop connected to port 2 with a statically assigned IP address on the same subnet as “dirtnet.” I am able to ping the local port 2 address, but I can’t ping across the tunnel to the anchor WLC. I also cannot ping the anchor WLC "dirtnet" interface from the foreign WLC’s Ping tool.
Cisco Wireless :: 4400 How To Get New Access Point To Be Seen By Controller
Jul 23, 2012I have a Cisco Series 4400 WLAN controller and I'm trying to connect a lightweight AP to the controller. I have already assigned the switch port to use my wi-fi VLAN, and have connected the AP to the switch. After a few minutes, the light on the AP goes from green to light blue (indicating it's serving clients). When I log into he wi-fi controller to look for the Ethernet mac address of the new AP, I do not see its Mac Address. I want to be able to rename the AP to reflect where it will be used, but need to select the AP via its Ethernet mac address before I can make any edits like changing its name etc. I've gone through the "monitoring" menu, selected "All" and still do not see it in their via its MAC address. I also will select the "wireless menu" which lists all the AP's on my network, listing in order from on the longest running, to just powered on.Is there something I'm missing like a "re-scan" that scan's all devices?
View 5 Replies View RelatedCisco Wireless :: WAP4410N Access Point Disconnect After Short While?
Jun 12, 2011I got a CISCO wap4410n access point and it is disconnecting uses after a shorl while. I hv to again connect them manually.
View 1 Replies View RelatedCisco Wireless :: 4400 - Laptops Unable To Access Domain
Dec 22, 2011We have a several cisco 4400 wireless controllers and a cisco WLC. All clients autheticate to an AAA server. Acces points are cisco LWAP 1242. Security is PEAP TKIP ms-chap. Machine and user authetication. Settings are pushed out through grou policy. A new user can log on to a laptop (without cached credetials) and get all their network settings....most of the time. Randomly we have laptops that after being restarted, recieve "yourdomain.com is not availalbe" error message. The laptops will work fine for weeks and then random laptops start to get this error. If we wire them into the network, run a gpupdate, they logon fine. Shutdown, unplug, and the wireless works fine again.. I am not sure if this is an ms group policy issue or a wireless issue. Any setting change or a gp setting that I may have missed??
Clients are mostly windows 7 some XP Domain Windows 2008r2
ACS 4.2
Group policy settings - wifi config settings enabled and configured correctly Always wait for network enabled.allow fast reconnect disabled (was recommended by a cisco tech) Disabled computer passwords for domain about 2 months ago to see if the computers reseting their passwords were an issue.
Cisco Wireless :: 3502 Access Point Will Not Connect To 4400 Series WLAN Controller
May 20, 2012I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies View RelatedTP-Link Dual-Band Wireless :: TL-WDR4300 Always Disconnect Connection / Prompt-up Limited Access
Nov 21, 2012Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : starhub
1) Always auto disconnect (limited access),
2) My smart phone Motorola MB860 (android 4.0.4) Can connect but can access internet.
3)Always connect to 2.4GHz ,never see connect to 5GHz.
4)Wireless connection 15-20 Max Mbps Only ,LAN can up to 50 Mbps .
Cisco Wireless :: 2960 - Autonomous Access Point / Get Guest To Access Internet?
May 9, 2012I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
Cisco VPN :: ASA 5500 - Remote Access VPN Intermittent Disconnect
Oct 11, 2012I am having the peculiar issue in our ASA5500 firewall (version 8.2(5) ), where the remote access vpn is getting issue, I am unable to ping the internal resource for sometime, however without any modification the problem gets resolves.
During the issue we can see Tx count 0
Username : xxxxxx Index : 3147
Assigned IP : 172.17.254.24 Public IP : 14.99.x.x
Protocol : IKE IPsec
License : IPsec
Encryption : 3DES AES128 Hashing : SHA1
Bytes Tx : 0 Bytes Rx : 8764
Group Policy : EMP-VPN Tunnel Group : EMP-VPN
Login Time : 15:07:51 IST Fri Oct 12 2012
Duration : 0h:06m:34s
Inactivity : 0h:00m:00s
NAC Result : Unknown
VLAN Mapping : N/A VLAN : none
Cisco :: 4400 Controllers Which Support 50 Access Points Each
Jun 25, 2011We have two 4400 controllers which support 50 Access points each and wcs with 100 base license.Now we added 5508 controller supports 50 access points.wcs is upgraded with another 50 ap license.The 5508 controller is joined to wcs and the licence showing permanent.WCS showing all aps and showing both 100 and 50 licence as permanent.But the issue is while loging into the wcs it showing the error message as"The system is in violation of license.The number of APs registered is greater then licensed."
View 5 Replies View RelatedCisco :: Any Chance To Access Files On 4400 With Ssh Clients
Mar 18, 2011Is there any chance to access files on 4400 with ssh (winscp etc.) clients ?
For example we upload webauth bundle and then we want to delete it and recopy another files..
Cisco :: WLC 4400 SNMP Traffic By Access Point
Mar 15, 2011I manage a wireless mesh solution (WLC 4404,4.2.176.51M (Mesh)) with some types of LAP, namelly,LAP1510, AIR-LAP1242AG-E-K9 and AIR-LAP1242G-E-K9.
We also use a freeware solution to have some graphs (collect by SNMP), namely for: Clients per AP, Noise and Interference, Channel Util, etc.
My question is about collect (by SNMP) the traffic (inOctets,outOctets) by access point, to have traffic utilization for both Radio (A and B/G) and ethernet interfaces of each access point... I can't find it on the MIBs... It´s possible?
Cisco :: 1240 / 4400 - Monitoring User Access
Mar 27, 2011Is there anyway to monitor client who is downloading , using the most bandwidth in Cisco wireless environment ? i have 1240 ap and 4400 controller environment.
View 1 Replies View RelatedGuest Wireless Access
Feb 11, 2013I understand you can have a guest wireless setup on the newer Access Points, and trunk (cisco term) the 2 VLANs and seperate them out with Access Control Lists so they don't talk to each other, but I would rather just give the VLAN 480 it's own DHCP from the router.
[code]...
Cisco :: 4400 - Push Network Time Out To Access Point
May 8, 2011We have 30+ wireless access points controlled by a Cisco 4400 Series WLC (mostly AP1231's and some AP1242's). The WLC's system time is set by a network NTP server and is correct. However the APs clock is an hour behind that of the controller.
View 3 Replies View RelatedCisco Wireless :: WLC 5508 Guest Access Via WAN?
Jan 28, 2012Is it possible to provide wireless guest access over the WAN from another office via the WLC. I have WLC 5508 in a central office and have other remote offices that have one Access Point in each office that are autonomous; I will be converting these to LWAPP. Is it possible to route guest traffic back to the WLC then forward this traffic out to the internet? How would I route this traffic out as well? install a secondary WLC in the DMZ and use anchor points. I only have one WLC
View 7 Replies View RelatedCisco Wireless :: WAP321 Don't Have Guest Access
Oct 11, 2012It's my intention optimize our business WiFi network.Actually we don't have a "Guest" access.Probably WAP321 should be the best solution for us.We will need 3 WAP321 to cover offices area.I have different questions/doubts about Captive Portal functionality.using 3 different WAP321 everyone has the "captive portal" feature, or you can configure only one of the three the feature of "captive portal"?if is possible to configure only one of three the feature of "captive portal", the others WAP321 trusting the authentication?what is the ip address released from the "Captive Portal"?all Guest user have the same username and password?
View 1 Replies View RelatedCisco :: WLC 2106 Guest Wireless Access
Dec 2, 2012We have a 2106 that was configured by a former employee. No one left in the company is qualified to configure it. The wireless guest access used to work fine. We'd configure a guest user account. They would connect to the guest wireless, open a web browser and login. For some reason now there is no prompt for login. People can connect to it and get an IP address, but that's it. No login prompt or anything else from there.User Login Policies was set to 0 and I put it to 8. That didn't do anything. Under Web Auth > Web Login Page it's set to Internal (Default).
View 5 Replies View RelatedCisco Wireless :: Guest Access On 5508 WLC
Feb 3, 2013I'm looking to implement guest WiFi access with web authentication on one of our 5508 WLC (currently deployed within a sandbox environment), but looking for some assistance. The WLC currently has a single connection from port 1 to the 'Test Site 2' switch. This is a dot1q trunk. On the WLC, the interface (for port 1) is configured as follows: [code] Currently, I have one WLAN configured with the profile name 'Guest Test 1', it's enabled and broadcasting the SSID. Security is L3 only with web authentication configured. The WLAN is configured to use the interface names "guest_wifi".
The issue is that when a client connects to the WLAN, it receives an IP address okay (10.99.254.x address), but doesn't seem to be able to contact the WLC to get the web authentication page. Eventually, the WLC terminates the connection due to an authentication failure.does it sound like I'm taking the correct approach here? The idea is that clients connect to the guest WLAN, which puts them on VLAN 99 and routes traffic through to the ASA and then onto the internet.
Cisco Wireless :: AP541N-A-K9 Guest Access Authentication
Nov 12, 2012I currently have two AP541N access points. Both are configured for internal access and one unit is configured with a Guest VAP. I want to configure the Guest VAP to redirect to an authentication page so that the user connecting has to log in to get internet access. I'm fairly certain the AP541N doesn't offer this out of the box. I know I can redirect, but what is needed to force a user to authenticate to gain internet access. I want to find out what additional hardware/software I will need in order to create Guest Services of this VAP.
View 1 Replies View RelatedCisco Wireless :: Does WAP4410N Support Guest Access?
Sep 13, 2011Does the Linksys AP (WAP4410N) support Wireless Guest access solution?
View 2 Replies View RelatedCisco Wireless :: WLC 5500 Guest Access Logging
Aug 8, 2012In the ISE documentation is states that under a Guest_Activity report you must have guest access logging enabled on the NAD in the ISE network. My question is where do I enable guest access logging in the WLC that is our NAD?
View 1 Replies View RelatedCisco Wireless :: 5508 -Architect Guest Access
Apr 11, 2012I just got a new requirement for our wireless roll out and I need some help. Plan the best way to provide employee and guests wireless access w/ the guests separate from the production environment.
We have a 5508 controller w/ 1142 APs. I have two GBICs in the interfaces (only one is being used). I want to use a back haul connection for the guest access. I am having a hard time in visioning how to physically set up the cabling from the patch panel. Again, the requirement is to not allow guest users to connect to our production network but I still want/need to manage the AP. This will eventually need to be supported for remote sites tunneling back to the primary location.
Cisco Wireless :: WLC 5508 - Guest Internet Access
Oct 28, 2011I am running a 5508 WLC with 10 Access Point. we need to allow Internet Access to Guest. 10MB DSL Internet is dedicated for Guest. This link is terminated on a regular ADSL modem without being part of our network. We want all Guest Internet traffic to reach the ADSL Router. where should I create the Guest VLAN / where the DHCP for Guest users should be created. what is the best practise for similar setup.
Our Network is simple
ISP_Reuter-------ASA_Firewall--------------4505------------LAN-switch 2950
ADSL_modem------------ users connect via wireless but restricted to certain area only.
Cisco Wireless :: WAP4410N Guest Network Access?
Apr 19, 2011I have two Cisco WAP4410N access points. Both has Regular and Guest SSIDs, with same configurations, except "Wireless Isolation" on Guest SSID is enabled. Problem is Guest SSIDs are not visible on devices
Access points are working on different chanles, firmware Version: 2.0.1.0.
Wireless :: No Wifi Log In Guest Access Page?
Apr 7, 2012I been using my mechanics Wifi connection with my internal wireless adapter for at least 6 months. Living next door he has a guest Wifi connection for his customers that requires a password. I only had to use the password once and since then it has automatically connected. I recently purchased a usb wirless adapter with an antenna to get a better signal and it connects to the server but the login access page will not display nor will it connect to the internet. With this I get error 102.
View 4 Replies View Related