We have 30+ wireless access points controlled by a Cisco 4400 Series WLC (mostly AP1231's and some AP1242's). The WLC's system time is set by a network NTP server and is correct. However the APs clock is an hour behind that of the controller.
View 3 RepliesI have a Cisco Series 4400 WLAN controller and I'm trying to connect a lightweight AP to the controller. I have already assigned the switch port to use my wi-fi VLAN, and have connected the AP to the switch. After a few minutes, the light on the AP goes from green to light blue (indicating it's serving clients). When I log into he wi-fi controller to look for the Ethernet mac address of the new AP, I do not see its Mac Address. I want to be able to rename the AP to reflect where it will be used, but need to select the AP via its Ethernet mac address before I can make any edits like changing its name etc. I've gone through the "monitoring" menu, selected "All" and still do not see it in their via its MAC address. I also will select the "wireless menu" which lists all the AP's on my network, listing in order from on the longest running, to just powered on.Is there something I'm missing like a "re-scan" that scan's all devices?
View 5 Replies View RelatedI manage a wireless mesh solution (WLC 4404,4.2.176.51M (Mesh)) with some types of LAP, namelly,LAP1510, AIR-LAP1242AG-E-K9 and AIR-LAP1242G-E-K9.
We also use a freeware solution to have some graphs (collect by SNMP), namely for: Clients per AP, Noise and Interference, Channel Util, etc.
My question is about collect (by SNMP) the traffic (inOctets,outOctets) by access point, to have traffic utilization for both Radio (A and B/G) and ethernet interfaces of each access point... I can't find it on the MIBs... It´s possible?
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies View Relatedis it possible to connect 2 wireless access point as same time to one laptop.
View 2 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I'm trying to modify the power transmission control of multiple Lightweight Access Points (1131 AG E K9) at one single time on WLC 4400 or WCS.It is effectively possible to configure the power transmission per LAP and in global on WLC 4400 but i need to configure it per group of LAPs =i.e group X of 10 LAPs will have a power Threshold of X -dBm and group Y of 15 LAPs with Y -dBm.
View 3 Replies View RelatedI am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies View RelatedI have 4 computers (3 laptops, 1 desktop) in a shared office. We get internet access using their wireless network. All works fine. However, I need to share a printer amongst all of the computers. The printer is LAN enabled and I would normally just put all the PCs on a hub, together with the printer and share it that way. BUT my question is can we access the internet using the wireless network and the printer using a separate wired network at the same time?
View 7 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 2 Replies View RelatedHow to time access restrictions with WRT120N router a wireless network?
View 7 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
my home has a wireless network, and I can get internet (wirelessly) on my PC perfectly. What I was wondering is if it would be possible for me to hook up an ethernet cable to the RJ port on my PC, and connect my PS3 to it to give me a wired internet connection on the PS3.
View 14 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
i live in a two story townhouse. under the stairs, there is a small closet where the modem and router are. there are also three ethernet ports, one that leads to each of the bedrooms. However, the only one that is being used is my room (my roommates dont need ethernet) so what i decided to do was run the ethernet port from the modem directly to my room and then connect the router to it using the ethernet port in my room. (my room is upstairs)
Now, this setup works great for me. I can connect my HD to the Airport and my printer via ethernet and my desktop as well. BUT ever since i moved the router upstairs to my room, the internet has been EXTREMELY slow downstairs
so this is what i was thinking, I want to get another wireless router and put it downstairs where the modem is, and use my airport Extreme as the "second" router. But, i want to use a different SSID for my airport extreme. is this possible?
I was thinking to connect the new router downstairs like normal, and disable the DHCP server on the airport extreme and change the IP address to make sure it isnt the same as the new router, then connect the new router to one of the three ethernet ports on my airport extreme.
Is that the correct way to set it up? and if i do that, would i be able to connect all my devices without a problem? (in addition to the devices mentioned earlier, i also have a second printer, a PS3, a home entertainment system, and sometimes my laptop, all connected to the airport via an ethernet switch) and lastly, will I be able to access the internet without a problem? will this slow down the internet that i get?
the reason i want to do this is because 1) I dont want any of my roommates or their guests to access my hard drive (i know, i can put a password on it. but still) and 2) if my printers are on the same network as their computers, they like to "accidentally" wirelessly print to my printers. I want to avoid that because they print. alot.
I want share my adsl internet connection to my galaxy tab and use labtop wirless as a access point. in toturials there is settings in wirless newworks tab in wirless propertice,but I cant found this tab. I installed lastest Wirless driver update and start WLAN autoconfige service. also I cant found microsoft virtual wifi in network connetions.
Intel wifi link 5100 AGN
Windows 7
We have a task of setting up 2 new WAP in our office. We have connected them to the network ethernet port and we can all connect which is great! However I need to change the wifi name and add security! Our server has DHCP.Everything I have seen online only refers to home network where the address is 192.168 etc..
View 3 Replies View RelatedI currently have a BT Home Hub 3 router and an Ubiquiti Power AP N. What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection. How would I be able to do this?I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 3 Replies View RelatedI have a computer in my room that I use and my parents have a computer in the work room with an wifi networking system. I have no access point to connect to the internet so how can I connect to the wifi?
View 2 Replies View RelatedWe have a wireless router, (Dlink DI-524, a couple of years old, and all the cables), and I have a basic knowledge of networking, such as DHCP servers and so on, but I don't know how to set it up. We have a working LAN port, so access isn't a problem. And we know the server address. As much as we'd like the IT dept. to do it, or to at least tell us how, they're unbelievably lazy and won't do either.
View 2 Replies View RelatedI think I know what I want, but I just wanted to check before I splashed the cash and made the wrong choiceI have a Humax Freesat recorder and a Panasonic Blu-Ray player. Both of which have services that need internet access, but neither are WIFI enabled & are the wrong side of the room to be connected via cabled ethernet.I believe that what I need is to wireless access point? I'd like one with a built in switch as well, as most seem to only come with only one port. The one I found has four, which would be useful as I could replace the poor wireless Xbox 360 dongle.
View 4 Replies View Relatedget the network key to connect with my Linksys WAP546 v 2 for my new laptop. Without this key it's not possible to make wireless contact
View 1 Replies View RelatedWhat I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View Related