We have a wireless router, (Dlink DI-524, a couple of years old, and all the cables), and I have a basic knowledge of networking, such as DHCP servers and so on, but I don't know how to set it up. We have a working LAN port, so access isn't a problem. And we know the server address. As much as we'd like the IT dept. to do it, or to at least tell us how, they're unbelievably lazy and won't do either.
View 2 RepliesHere's the setup:
DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
I have an existing wireless network using a Cisco/Linksys WRT400N wireless router (which in turn is connected to a cable internet provider). I need to extend my wireless coverage and so purchased a Cisco/Linksys E1000 to act as an additional access point. Purchased from BB, the local 'geek squad' rep instructed me to follow the users guide for the set up. After login into the admin service on my E1000, I followed the 'Advanced Routing' instructions and disabled the 'NAT' option and subsequently enabled the 'Dynamic Routing (RIP)' option. Everything worked like a charm to this point, but now I'm stuck. What steps do I need to follow to allow clients to log onto my wirelss network via the E1000 (secondary access point)? I've established WEP security keys on the WRT400N (primary access point) and want to use the same network security parameters on the E1000.
View 9 Replies View RelatedI am attempting to install a D-LINK DWL3200 into my office network. I can't for the life of me get into the router though to change the password and name!I've read through various forums about running ipconfig and that giving me the gateway - However, we main router where the internet runs through so the IP address of the gateway is the main router! The default IP address listed on several forums is 192.168.0.50, but as everything in this network has an IP .50 is a printer!
View 2 Replies View RelatedI am trying to add a 2nd wireless access point to my network at work basically to allow a better wireless signal on a 2nd floor.1st Access Point is a LInksys WAP54G Wireless G Access Point.I had a Belkin F5D7234-4 ver 4 G Wireless Router at home that I brought in to use as the 2nd access point. IP info on the Linksys is 192.168.1.245, subnet is 255.255.255.0, Gateway is 192.168.1.1.The Belkin has been reset to factory defauts so IP is 192.168.2.1.If I connect my PC directly to the router using one of the wired ports not the modem port, I can access the router webpage.As soon as I enable access point mode and change the router IP to 192.168.1.246,I lose the router and cannot access it at all to finish the network configuration.
View 6 Replies View RelatedI am staying with some family for the next two months and they don't have wireless internet at their house. When they bought their house it was wired for ethernet and have the modem going to a netgear 8 port switch which is going to the different rooms of the house. I would like to add a wireless access point to one of those 8 ports coming from the switch. I currently have a TP-LINK TLWR740N router that I can configure into an access point, or I can buy just and access point. Unfortunately it is not an option for me to plug the modem into the router and then the router into the switch.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedWe have a task of setting up 2 new WAP in our office. We have connected them to the network ethernet port and we can all connect which is great! However I need to change the wifi name and add security! Our server has DHCP.Everything I have seen online only refers to home network where the address is 192.168 etc..
View 3 Replies View RelatedHere's the deal. My internet provider provided me with a shitty router with a lot of settings locked. I can't change DHCP settings or add custom static IP addresses. This sucks. The wireless function on it sucks also.I added an extra router to the network so I have good Wifi in my living room. I turned off the NAT, firewall and DHCP on that one, so it's a simple switch with a wireless access point now.Now here's the deal. The DHCP server of the provider's router hands out IP's from 192.168.2.1 to 192.168.2.253 (192.168.2.254 is the router's own IP address).I gave the added switch/access point the IP address 192.168.1.1 in its own settings. The original router doesn't 'see' the switch now anymore because it's out of the DHCP's range. When I gave it an IP address within the DHCP's IP range, I got all kinds of conflicts (as expected).
I guess this is a solution since it works, but I'm open to other suggestions since it doesn't seem to be the best way of doing things. Besides, I can't access the access point's web interface anymore since it doesn't have an IP address within the network now. It isn't important because I don't need to change any settings anymore, but still.I'm going to add a second wireless router to replace the built-in wireless function of the provider's router. For some reason it sees its own wireless network as a separate network or something. When I roam from the new access point wifi to the provider router's wifi, everything gets confused because it tries to give the laptop a new IP address.
it is each wireless access point need to have different subnet, if 24 users connect at the same time? will it be slow down if 24 user put in the same network?
View 1 Replies View RelatedWhy can't I see my truemobile 4350 network access point? I have two cards on my laptop one works fine with one (netgear) access point. The other worked until I re-booted my system, now both cards connect to one access point and I can not even see the second access point.
View 3 Replies View RelatedI'm setting up a small network (one server, two clients) to create photo sales kiosks at an upcoming outdoor event. I will need internet access for processing credit card payments but there won't be any wi-fi or ethernet internet access on the site so I'll need to utilize my iPhone's 3G connection. I recently installed "MyWi" app which can tether the 3G and even create a personal wi-fi hotspot but unfortunately it only works in ad-hoc mode, not infrastructure.So far, the wired LAN is working great on my three Macbooks, using a Linksys (DD-WRT) router. Also, the wi-fi hotspot is working great to provide internet to all the computers. The problem, of course, is that I can't have both connected at the same time or else everything breaks. I've tried doing an iPhone-USB-Macbook tether and then sharing the connection via ethernet but the internet doesn't get through the router (because I don't have a clue of how to configure the router for this). I've also tried setting my router (DD-WRT) to do a client-bridge of the iPhone ad-hoc wi-fi, but again, it's way over my head and didn't work.
View 2 Replies View RelatedI had an old G router that had an unsecured network. It died and I replaced it with an N router and installed a secured network. I have a cable modem with wires that goes to the router. From the router, I have CAT 4 wires going to several access points around the house. Into one of these acess points, I have pluged in a wireless access point that broadcasts wirelessly---unfortunately, it is broadcasting the old unsecured network. How can I make the wireless access point broadcast the new secured N network?
View 6 Replies View RelatedI have a 4 year old Linksys WRT54G V8 I'd like to set up as an access point for an Xbox 360 or DirecTV box. I am using a Linksys E3000 as my wrieless router, atm, and was wondering if there was anyway to use the WRT54G as an access point before I go out and buy other network adapters to get these devices connected.
View 2 Replies View RelatedCan I add an AP541N into a existing wireless network of WAP4410N's without any issues.
View 4 Replies View RelatedI currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies View RelatedI'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?
View 8 Replies View RelatedI am trying to improve the coverage of my home network.I have Fios, and with the existing Wireless capabilities, there are several dead and low coverage areas in my house. This is due to a combination of where my router is (Limited by input feed) and the confuration of the house.
I have CAT-5 running to most rooms, so adding wired devices is not an issue. I went out and picked up an EA4500 router, and my plan was to convert my Fios Router to a bridge and use the EA4500 as the DHCP server. However, even with this router, my coverage is not improved. My preferred solution will be to get 1 or 2 additional access points that I can plug into my wired network, however, I would want to have a common SSID for the entire network.
I want to use one (or two) AP1232AG-E-K9 access points for Internet connection through a public wireless network (BTFON), where wire broadband is not an option. I've downloaded what I think is the correct manual for the APs and I'm now scratching my head as to where and how to start setting them up. I want to use these Cisco APs in the hope they will give me better wireless performance than I'm currently getting, which is frequently flakey. I've tried to reset the APs to the factory default but there seem to be different ways of doing this depending on what you want and what you've got. I made up a console cable to access the console but there even appear to be different versions of this so I'm not sure if the cable I have is the correct one. I have setup and used lower end wireless devices in the past but these Cisco units seem real complicated.
View 39 Replies View RelatedI have a tplink acess point TL-wa5110G . I have WISP ( wireless internet service provider). I have configured the acess point on wisp client router mode and wan type to pppoe gave the username and pwd..Now i want to share internet wirelessly. now my question is that can i connect the aces point to wan port of the wirless router to share internet wirlessly? Because i have seen the instruction figure in tplink access router where they have shown that u can connect it with with unmanage able switch to share it to wired lan.i want to ask can wirless works to share internet if i use wireless router to access point.
View 1 Replies View RelatedI work at a small business that has an exisiting wired network. Our setup is: Internet > ISP Box > DHCP Server > Switch > Users. I have been attempting to add a wireless router to the network to enable our shop techs to wirelessly access our file computer. I have managed to get the wireless working, but the network was not visible, I could not access any network computers from the wireless, and I could not access the wireless router from our main server. After this I screwed up the settings completely and even a wired connection to the router couldn't connect to the internet. Now I have purchased a WAP54G, but I forsee the same problems when I go to config everything tomorrow.
View 2 Replies View Related,I was having problems connecting to a network that is TKIP secured with a WMP11 Wireless PC card. I'm wondering if this is possible.
View 9 Replies View RelatedI have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedI have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 2 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View Related