DLINK DWL3200 - Adding An Access Point Within A Network
Oct 24, 2012
I am attempting to install a D-LINK DWL3200 into my office network. I can't for the life of me get into the router though to change the password and name!I've read through various forums about running ipconfig and that giving me the gateway - However, we main router where the internet runs through so the IP address of the gateway is the main router! The default IP address listed on several forums is 192.168.0.50, but as everything in this network has an IP .50 is a printer!
View 2 Replies
ADVERTISEMENT
Jan 22, 2013
We have a wireless router, (Dlink DI-524, a couple of years old, and all the cables), and I have a basic knowledge of networking, such as DHCP servers and so on, but I don't know how to set it up. We have a working LAN port, so access isn't a problem. And we know the server address. As much as we'd like the IT dept. to do it, or to at least tell us how, they're unbelievably lazy and won't do either.
View 2 Replies
View Related
Dec 27, 2010
Here's the setup:
DGL-4100 (wired gigabit router)
-> Wii
-> X360
-> PS3
-> DGS-2205 (wired gigabit switch in study)
*-> My PC
*-> Her PC
*-> DAP-1522 (wireless access point/bridge)
Now, we're on the 192.168.1.x domain, and I've already hooked my PC up directly to the DAP-1522 and switched its IP address. So now, I can connect to it through the switch. I've renamed it, set it to WPA2 with a passphrase, and should be set to go. However, I can't get my laptop, IPod touch, or any devices to see it. I tried entering the SSID manually, and nothing can find it.
View 2 Replies
View Related
Oct 26, 2010
I have an existing wireless network using a Cisco/Linksys WRT400N wireless router (which in turn is connected to a cable internet provider). I need to extend my wireless coverage and so purchased a Cisco/Linksys E1000 to act as an additional access point. Purchased from BB, the local 'geek squad' rep instructed me to follow the users guide for the set up. After login into the admin service on my E1000, I followed the 'Advanced Routing' instructions and disabled the 'NAT' option and subsequently enabled the 'Dynamic Routing (RIP)' option. Everything worked like a charm to this point, but now I'm stuck. What steps do I need to follow to allow clients to log onto my wirelss network via the E1000 (secondary access point)? I've established WEP security keys on the WRT400N (primary access point) and want to use the same network security parameters on the E1000.
View 9 Replies
View Related
Jan 3, 2013
I'd like to set up my new d-link access point
View 1 Replies
View Related
May 24, 2012
I am trying to add a 2nd wireless access point to my network at work basically to allow a better wireless signal on a 2nd floor.1st Access Point is a LInksys WAP54G Wireless G Access Point.I had a Belkin F5D7234-4 ver 4 G Wireless Router at home that I brought in to use as the 2nd access point. IP info on the Linksys is 192.168.1.245, subnet is 255.255.255.0, Gateway is 192.168.1.1.The Belkin has been reset to factory defauts so IP is 192.168.2.1.If I connect my PC directly to the router using one of the wired ports not the modem port, I can access the router webpage.As soon as I enable access point mode and change the router IP to 192.168.1.246,I lose the router and cannot access it at all to finish the network configuration.
View 6 Replies
View Related
Jan 7, 2012
I am staying with some family for the next two months and they don't have wireless internet at their house. When they bought their house it was wired for ethernet and have the modem going to a netgear 8 port switch which is going to the different rooms of the house. I would like to add a wireless access point to one of those 8 ports coming from the switch. I currently have a TP-LINK TLWR740N router that I can configure into an access point, or I can buy just and access point. Unfortunately it is not an option for me to plug the modem into the router and then the router into the switch.
View 1 Replies
View Related
Dec 12, 2011
I want to link a tp link router as access point to a d-link router.
View 2 Replies
View Related
Apr 2, 2011
I have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?
View 2 Replies
View Related
Nov 24, 2011
I have a dell inspiron laptop with windows vista installed. I have been traveling all over Germany and automatically detecting internet wherever I go however I cannot detect the dlink wireless access point directly across from me. My work computer is detecting and connecting just fine. I see other wireless networks just not the one I have a password for so I cannot connect. I have reset and seperately restarted the wireless access point but no luck. I am in desperate need of this wireless access. There is no line I can plug into manually either. I have also tried to manually set up the network and that either did not work or I did not go about it correctly.
View 4 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Apr 11, 2012
Here's the deal. My internet provider provided me with a shitty router with a lot of settings locked. I can't change DHCP settings or add custom static IP addresses. This sucks. The wireless function on it sucks also.I added an extra router to the network so I have good Wifi in my living room. I turned off the NAT, firewall and DHCP on that one, so it's a simple switch with a wireless access point now.Now here's the deal. The DHCP server of the provider's router hands out IP's from 192.168.2.1 to 192.168.2.253 (192.168.2.254 is the router's own IP address).I gave the added switch/access point the IP address 192.168.1.1 in its own settings. The original router doesn't 'see' the switch now anymore because it's out of the DHCP's range. When I gave it an IP address within the DHCP's IP range, I got all kinds of conflicts (as expected).
I guess this is a solution since it works, but I'm open to other suggestions since it doesn't seem to be the best way of doing things. Besides, I can't access the access point's web interface anymore since it doesn't have an IP address within the network now. It isn't important because I don't need to change any settings anymore, but still.I'm going to add a second wireless router to replace the built-in wireless function of the provider's router. For some reason it sees its own wireless network as a separate network or something. When I roam from the new access point wifi to the provider router's wifi, everything gets confused because it tries to give the laptop a new IP address.
View 4 Replies
View Related
Mar 10, 2011
I'm setting up a small network (one server, two clients) to create photo sales kiosks at an upcoming outdoor event. I will need internet access for processing credit card payments but there won't be any wi-fi or ethernet internet access on the site so I'll need to utilize my iPhone's 3G connection. I recently installed "MyWi" app which can tether the 3G and even create a personal wi-fi hotspot but unfortunately it only works in ad-hoc mode, not infrastructure.So far, the wired LAN is working great on my three Macbooks, using a Linksys (DD-WRT) router. Also, the wi-fi hotspot is working great to provide internet to all the computers. The problem, of course, is that I can't have both connected at the same time or else everything breaks. I've tried doing an iPhone-USB-Macbook tether and then sharing the connection via ethernet but the internet doesn't get through the router (because I don't have a clue of how to configure the router for this). I've also tried setting my router (DD-WRT) to do a client-bridge of the iPhone ad-hoc wi-fi, but again, it's way over my head and didn't work.
View 2 Replies
View Related
Apr 25, 2012
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
View 6 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 15, 2012
I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 2 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Feb 17, 2011
my home has a wireless network, and I can get internet (wirelessly) on my PC perfectly. What I was wondering is if it would be possible for me to hook up an ethernet cable to the RJ port on my PC, and connect my PS3 to it to give me a wired internet connection on the PS3.
View 14 Replies
View Related
Apr 19, 2012
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
View 2 Replies
View Related
Apr 22, 2011
i live in a two story townhouse. under the stairs, there is a small closet where the modem and router are. there are also three ethernet ports, one that leads to each of the bedrooms. However, the only one that is being used is my room (my roommates dont need ethernet) so what i decided to do was run the ethernet port from the modem directly to my room and then connect the router to it using the ethernet port in my room. (my room is upstairs)
Now, this setup works great for me. I can connect my HD to the Airport and my printer via ethernet and my desktop as well. BUT ever since i moved the router upstairs to my room, the internet has been EXTREMELY slow downstairs
so this is what i was thinking, I want to get another wireless router and put it downstairs where the modem is, and use my airport Extreme as the "second" router. But, i want to use a different SSID for my airport extreme. is this possible?
I was thinking to connect the new router downstairs like normal, and disable the DHCP server on the airport extreme and change the IP address to make sure it isnt the same as the new router, then connect the new router to one of the three ethernet ports on my airport extreme.
Is that the correct way to set it up? and if i do that, would i be able to connect all my devices without a problem? (in addition to the devices mentioned earlier, i also have a second printer, a PS3, a home entertainment system, and sometimes my laptop, all connected to the airport via an ethernet switch) and lastly, will I be able to access the internet without a problem? will this slow down the internet that i get?
the reason i want to do this is because 1) I dont want any of my roommates or their guests to access my hard drive (i know, i can put a password on it. but still) and 2) if my printers are on the same network as their computers, they like to "accidentally" wirelessly print to my printers. I want to avoid that because they print. alot.
View 4 Replies
View Related
Jun 28, 2011
I want share my adsl internet connection to my galaxy tab and use labtop wirless as a access point. in toturials there is settings in wirless newworks tab in wirless propertice,but I cant found this tab. I installed lastest Wirless driver update and start WLAN autoconfige service. also I cant found microsoft virtual wifi in network connetions.
Intel wifi link 5100 AGN
Windows 7
View 1 Replies
View Related
Jul 3, 2012
We have a task of setting up 2 new WAP in our office. We have connected them to the network ethernet port and we can all connect which is great! However I need to change the wifi name and add security! Our server has DHCP.Everything I have seen online only refers to home network where the address is 192.168 etc..
View 3 Replies
View Related
Aug 15, 2012
I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N. What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection. How would I be able to do this?I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 3 Replies
View Related
Feb 29, 2012
I have a computer in my room that I use and my parents have a computer in the work room with an wifi networking system. I have no access point to connect to the internet so how can I connect to the wifi?
View 2 Replies
View Related
Dec 28, 2011
I think I know what I want, but I just wanted to check before I splashed the cash and made the wrong choiceI have a Humax Freesat recorder and a Panasonic Blu-Ray player. Both of which have services that need internet access, but neither are WIFI enabled & are the wrong side of the room to be connected via cabled ethernet.I believe that what I need is to wireless access point? I'd like one with a built in switch as well, as most seem to only come with only one port. The one I found has four, which would be useful as I could replace the poor wireless Xbox 360 dongle.
View 4 Replies
View Related
Sep 9, 2011
get the network key to connect with my Linksys WAP546 v 2 for my new laptop. Without this key it's not possible to make wireless contact
View 1 Replies
View Related
