I have a computer in my room that I use and my parents have a computer in the work room with an wifi networking system. I have no access point to connect to the internet so how can I connect to the wifi?
View 2 RepliesI think I know what I want, but I just wanted to check before I splashed the cash and made the wrong choiceI have a Humax Freesat recorder and a Panasonic Blu-Ray player. Both of which have services that need internet access, but neither are WIFI enabled & are the wrong side of the room to be connected via cabled ethernet.I believe that what I need is to wireless access point? I'd like one with a built in switch as well, as most seem to only come with only one port. The one I found has four, which would be useful as I could replace the poor wireless Xbox 360 dongle.
View 4 Replies View RelatedI have a seemingly simple desire: to achieve acceptable wifi coverage of my entire house and the ability to use my wireless devices in multiple locations within that house. To achieve this aim I have tried a variety of hardware combinations over the last two months but am now at the point where I'm almost ready to abandon the project.In my current setup I have:Downstairs: A new & working Wireless Router (TP-Link TD-W8961ND) from which I can connect to (1) the internet, and (2) the internal network devices (NAS, printer, and network shares). Broadcasting on channel #1. DHCP = On.Upstairs: A new & working Access Point (TP-Link TL-WA801ND).The AP is connected by a physical cable to the downstairs router. The AP is in "Access Point Mode" with the same SSID and security settings as the router.
From the AP I can also connect to (1) the internet, and (2) the internal network devices (NAS, printer, and network shares). Broadcasting on channel #11. DHCP = Off.Clearly therefore, parts of my setup are correct and complete. However, I cannot roam between these two devices. Once a device is connected to one of these devices it cannot connect to the other. When downstairs, if I connect any device (iPad, iPhone, Win7 ThinkPad, WinXP Netbook) to the router's Wifi network, it connects to the router as expected and is fine.
When upstairs, it connects to the second router but cannot get to the internet (it gets an IP address beginning with 169.). It reports a "Strong" connection but simply cannot establish a useful connection with the world outside the house. The same is true if I take a machine that is successfully connected to the upstairs network and move downstairs.Have you successfully setup a wifi network with a TP-Link router and a TP-Link Access Point so that roaming works? If so, what's the secret?! Should I use the "Bridge with AP" mode for the AP?
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I have set up a home network some time ago, using a 4-port wired router. All four ports are in use, one of which by my own desktop computer running Windows XP Home, SP3.I recently received a new laptop running Windows 7 Home Premium (64 bit). Because I can't afford a wireless router at the moment, I've been trying to set up my Windows XP computer as a wireless access point (using a Wireless LAN PCI card), so I can connect my laptop to it and share my internet connection.However, when I try to set up an ad hoc network on my XP computer, it doesn't show up in the list of available networks on my laptop, though it does show up on the XP computer, with the message that it's waiting for other computers to join.The same thing happens the other way around. When I try setting up an ad hoc network on my laptop, it doesn't show up on my desktop computer.
View 3 Replies View RelatedI have a Mac G5 desktop that has no wireless capabilities. I also have a Gateway laptop for work. It runs windows 7 and obviously has WIFI. Can i connect my Desktop to my laptop to use the wifi to connect to the internet?
View 2 Replies View RelatedI've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.
View 3 Replies View RelatedI've got a Livebox router/modem that provides an ethernet connection for our desktop and wifi connections for our smartphones (all-in-one kind of thing) in a SOHO environment. what i'd like to do is access one from the other, that is move files between a smartphone and the desktop without additional wiring or hardware.
View 1 Replies View Relatedhave been trying to connect my Wi-fi Access point but sytem shows , windows was unable to connect , however i have checked that access point with my friend laptop that was working fine, i have re installed my wi-fi network adapter , but the problem is same.
View 1 Replies View RelatedI wish to turn my TP-Link wireless router into an access point but can't figure out how to do it. I have tried several times but without any success. Below are my information about my main router and the router I want to turn into an access point:
1- Main Router: TP-LINK 3G/4G Wireless N Router 300Mbps - Model No. TL-MR3420. url..
2- Router I wish to turn into an access point:TP-LINK Wireless N Router 150Mbps - Model No. TL-WR740N. url...
My desktops _usually_ connect, and then the connection will drop/go slow(14400 slow)/give that little yelow triangle on top of the wifi icon.First i had an edimax wifi PCI, now i have a trendnet wifi PCI. They both do the same thing.If i connect my HTC hero and start internet sharing, it works very well, and is stable. My ethernet works fine as well. It is like my computer is immune to PCI cards?I have tried with different wifi APs now, but its still the same.I have a zyxel adsl modem, and a linksys wifi AP hooked up to that. I noticed, that when my desktop is connected, the zyxel will get some kind of overflow from the linksys. It says "client reached max number of sessions per host" It's like my desktop is killing the network. I have tried many things. Drivers, fail safe, registry cleaner(I know), killing all unnescessary program, switching the PCI ports, but none of it seems to work.
I had my laptop running connectify (access point app) and it actually worked fine, but today it won't connect to that either.I'm going to create another partition on my harddrive, and install fresh windows 7 on that, and see if it does the same. But even if it doesn't I _want_ to find out what is causing this instabillity.When i try running the network diagnostics, it says DNS error, or that the router is fail. But my laptop works fine.Also, when doing speed tests, my laptop gets normal speeds, and my desktop is VERY slow DL, but normal UL ?In speed tests my desktop is very slow, but stable, but during the test, my laptop will first go like 2 mb/s - 3mb/s DL and suddently BURST up to like 64 mb/s although i only have 10 mbit line? It's like its buffering or something. Very weird behaviour, but working fine.And no, i do not have torrent programs or whatever running.Some says that i shout try and change wifi channel and bands, and avoid "mixed" mode, but none of it works. Always the same problem.ATM. my computer can't connect to any wifi at all. It keeps having the yellow triangle.
how to set up a Belkin F5D7230-4 6000 router as a wifi access point. My home set up is the following: Dell Desktop connected by Lan to a Telefonica/Movistar router (I live in Spain), Dell portable .. connected by wifi at the other end of the house ..saying it's portable is a bit of a joke .. it's old and moving it is not an option ! Problem is I don't get much wifi signal on the portable to be able to do anything at all online so after googling on how to increase wifi signal .. worked out that I could set up an access point.. and owning a belkin router have been trying to set it up although I think there is something
I've connected the belkin by cable to the portable and disabled the DCHP and clicked on set up as an access point, set up wifi security and password, but when i am trying to reset the IP address I end up having to reset the router and start all over again.
I have a Windows XP SP3 desktop with a NetGear WG111v2 USB wireless adapter and I get my internet connection from my Blackberry 8320 (I connect my BBerry device to my PC and start Blackberry Desktop Manager and choose to use internet access of my phone for my PC). I want to be able to make this internet connection available to other devices on the network wirelesly. I also have a nook ebook reader and a laptop which I would occassionaly like to connect to internet via the connection described above. How to go about making Blackberry internet connection shared accross the network? I tried Internet Connection Sharing Wizard, but I ended up with nothing to show up for.
View 3 Replies View RelatedI have an E2500 running as a router/DHCP server. For reasons beyond the scope of this question, I am replacing the router and DHCP functions with a SonicWALL device. I would like to continue to use the E2500 as a wireless access point only, providing WiFi connection to the SonicWALL. How do I set up the E2500 for this purpose. I assume I switch off the DHCP server and NAT within the device. Is there a dedicated "access point" mode?
View 9 Replies View RelatedWe have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?
I need a wifi extender for wag 120n , and i want to connect it with WDSI use wag 120n as main and only modem and access pointWhat is the best and cheapest device for me?
View 1 Replies View RelatedI have an existing home network with a D-link wireless router, IP 192.168.0.1. In the past, I set up another of the same model Dlink router as a WAP to extend my network by simply disabling DHCP and setting its IP to 192.168.0.100. Used the same SSID and passwords, worked flawlessly. Now, my WAP-router has failed and I purchased a LINKSYS E2500 to replace it in that function. I'm trying to configure it the same way but am having problems.The Linksys' IP is 192.168.1.1 by default. I hooked its LAN port to my laptop and accessed the setup page at 192.168.1.1. I changed the router IP to 192.168.0.200 and disabled DHCP. I saved settings, the router reset, and since, I am unable to re-connect to that router setup screen at either 192.168.0.200 OR the default 192.168.1.1. I reset the router to default and tried this multiple times but could never get back to the setup page (didn't even configure any wireless settings yet) after I made the IP change and disabled DHCP. With my previous router, this worked easily and flawlessly.
1. What am I doing wrong (ok, other than using Dlink components)?
2. Should these two different brand components work ok together llike this or is that a problem?
3. Why should unticking DHCP and/or changing the IP address as described make the device unreachable?
I would like to use the DAP-1522 as an Access Point (wired to my router). My two concerns are:Can the 3 remaining ethernet ports be used to wirely connect to local PCs (so the DAP-1522 also acts as a switch) ? In case answer to the previous is yes, would it affect the performances of the wifi ?
View 3 Replies View Relatedcan you use a Mini USB WiFi Wireless Adapter LAN Network Card on a desktop computer
View 4 Replies View RelatedI have the Netgear wndr4500 router setup as an AP. The wndr4500 has a feature for guest wifi but will not connect to the internet. The main wifi will connect to the internet fine. I'm wondering if I use the WNDR4500 as an AP, the guest features do not work?
View 2 Replies View RelatedI've been having trouble with my wrt54gs2 and 4 360's. I tried a link someone posted for me to a cisco tutorial, it worked, but only for one 360. I have a Netgear wndr3400, I HATE the wireless on that router. Its unreliable but I like the features, the guest network and transfer meter, plus its worked with 4 360's out of the box. So would it be possible to turn off my wifi on the Netgear and plug the wrt54gs2 in and use its wireless?
View 7 Replies View RelatedI use a Cisco 871W router for my office in home -- I have Wifi working and want to add my new Blu-Ray player to the network -- I bought a WAP54G to use as a wireless bridge assuming i woudl just connect the WAP to the BLU-Ray with a ethernet cord. The instructions for installation of the WAP include connecting it to my router for the set up but the installation disk says it is not recognizing the WAP. I use Brighthouse for my ISP and the connection sequence is BH Modem to teh Cisco 871W -- the 871W directly connects to my CPU and to a Net gear FS105 fast network Switch -- the swicth connects to my VOIP phone , HP printer and external HD back-up system -- there is an open port onthe FS105 and two open LAN ports on the 871W.
I tried to install the WAP but connecting it to both the router and the swtich without luck. Is the WAP what I need to connect the Blu-Ray --- am i missing something in the set up?
I am having trouble connecting my device to certain WiFi networks. We work with hotels and we have a handful of devices that are just not able to connect to their network. Te device works fine in my office. When I get to the Setup page and do a site survey, it'll get to 100% and then display a "page can't be found" as oppose to showing me that it has been connected. We had the MAC address cleared in their network and still no luck. Firmware has also been updated.
View 7 Replies View RelatedI just recently bought this router (DIR-615 rev E3) to act as a Access Point for the dead wifi spot in my room downstairs. I set up everything properly (Turned off DCHP, set ports and gateway..subnet blah blah) and it was working fine. My wireless speeds were perfect, and had no issues with that. However, my wired speed was significantly slowed down. I have Verizon Fios and have the wire from that plugged in to LAN port 1 on my DIR-615. I have another wire going from Port 2 to the back of my PC. My normal speeds are about 30mbps down and 25mbps up. When I connect my internet through the second router (DIR-615) I get a maximum of about 3.0mbps up and down, doesn't go much higher than that. The wireless however, gives me about 11mbps both ways, which is fine.
I thought it might have been a firmware issue so I flashed to DD-WRT (build 15778), but the problem persists. I've tried most everything and am getting desperate. There's absolutely no logical reasoning for the slowdown. I have confirmed it's a router issue because I also turned off wireless on my laptop and plugged that directly into the router instead of my desktop and get the same 3mbps.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedGot 1 Linksys WRT54G Router on the ground floor which uses PTCL DSL Internet and 1 D-Link Wireless N Gigabit Router on the first floor which uses World Call Cable Internet of my house. So yeah we have two internet connections.Getting weak signals from both of the routers in my room on the far left side of the house and little to no signals in the basementSo what I want to ask is that should I purchase better routers or should I go with a signal booster of some sorts like an Access Point or a Range Extender?Also is there such a device which would catch signals from both of these differently configured routers ( different internets, different wireless security keys etc ) and then boost them throughout the house if placed in an area where both the router signals are strong?
View 5 Replies View RelatedI am using an E2500 as an access point, which is working fine. I have an Ethernet cable on one of the LAN ports of the E2500 connected to a LAN port on my gateway router. The LAN address of the E2500 is 192.168.7.3 and the LAN address of the gateway router is 192.168.7.1. Clients on the E2500 wireless network have no problems getting to the Internet through the gateway router. Clients on the E2500 wireless network can reach the E2500 local management port at 192.168.7.3 on port 80. On the gateway router I am forwarding WAN port 8083 to LAN address 192.168.7.3 at port 80. But I cannot access the E2500 local management interface via the gateway router. The E2500 should see the request as from 192.168.3.1 due to NAT in the gateway router, right? I can reach any of my actual access points this way, just not a router being used as an access point. Security/design limitation of the router?
View 2 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 2 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedMy wired desktop cannot access the internet. Its still connected to my home network however. Every other computer on the network can connect to both the network and the internet just fine. the wired desktop is running windows xp. I have tried renewing the ip address, resetting IE settings, disabling the firewall, and I am currently running an anti-virus scan.
View 2 Replies View RelatedI have a Linksys wireless G Router (WRT54G5 model) and I've recently had some problems with it. First problem, I cant find my wireless network from my desktop, but it shows up on my laptop but it wont let me access it from there. The power, wlan, port 1, and internet led lights are all on and green. How can I get my wireless network to show up on my desktop and how can I access it from my laptop? If I unplug my router for 30 seconds and plug it.
View 17 Replies View Related