have been trying to connect my Wi-fi Access point but sytem shows , windows was unable to connect , however i have checked that access point with my friend laptop that was working fine, i have re installed my wi-fi network adapter , but the problem is same.
View 1 RepliesI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Setup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.
View 2 Replies View RelatedI am not able to access my wireless access point anymore. I tried to access the web configuration in my browser as I have in the past 192.168.1.245, but I have no luck there. I tried to reset it by holding the reset button for 10-30 seconds, and I have no luck with that. What I have noticed on the AP is that the ethernet light keeps going out. The only light that is lit on my AP is the power and sometimes the ethernet light. My AP is connected to my router which I am able to gain access to the internet from any devices connected to the router except the AP. I have a router (E2000), a WAP4400N, and switch. I want to keep my wireless access separate from my business network. I cannot get my WAP4400N to work anymore.
View 1 Replies View RelatedI've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.
View 3 Replies View RelatedI'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies View RelatedI've recently purchased 5 WAP610N access points to replace my older US Robotincs access points.I've configured one WAP610N (upgraded to the latest firmware i found on the site) with a static IP, bropadcasted SSID & WPA2 personal security.I had no problem at all to connect PC's but when i tried to connect the Ipad & Iphone (with the latest 4.3 firmware) i was able to connect to the network but unable to get an IP lease.
I had no problem before connecting to the US roboticx access points.When i change (lower) the security to WEP on the WAP610N then everything works fine but i want to use WPA2 in stead of the unsecure WEP protocol.
I have a computer in my room that I use and my parents have a computer in the work room with an wifi networking system. I have no access point to connect to the internet so how can I connect to the wifi?
View 2 Replies View RelatedI think I know what I want, but I just wanted to check before I splashed the cash and made the wrong choiceI have a Humax Freesat recorder and a Panasonic Blu-Ray player. Both of which have services that need internet access, but neither are WIFI enabled & are the wrong side of the room to be connected via cabled ethernet.I believe that what I need is to wireless access point? I'd like one with a built in switch as well, as most seem to only come with only one port. The one I found has four, which would be useful as I could replace the poor wireless Xbox 360 dongle.
View 4 Replies View RelatedI have a wap610n access point, which failed during an upgrade. Now it just comes on with the power led and the network led blinking but there is no connection. i have tried the 30/30/30 resetting process but its still not working.
View 1 Replies View RelatedI bought a Linksys WAP610N today, i placed it so i could get a signal where i can't normally.
The thing is i configured it correctly, well at least i think, i can see it on my wireless network, with a good signal, but on my Android tablet (Google Nexus 7), it can't get past the "Obtaining IP address".
I called the technical support, the person there tried to assist me for about 1 hour, we tried different settings, we upgraded firmware from 1.0.01 to 1.0.04, but it didn't worked. Now he said someone will call me tomorrow during the afternoon.
My router isn't Linksys, it's a Netgear, i don't have wireless problem when i connect my tablets or any other wireless device on it, it's just that i bought this WAP610N to have the signal in my bedroom, where i don't get any signal normally.
I set up my internet access by adsl modem as gateway, then RV042 as load balancer and dhcp server, security by MAC address restriction and static IP assignment. WAP 610N used as access point.works great for first few weeks, then somehow I can't access the network.I've been using linksys on my SOHO network, no problem before (RV042+WAP54g)
View 9 Replies View RelatedI have a seemingly simple desire: to achieve acceptable wifi coverage of my entire house and the ability to use my wireless devices in multiple locations within that house. To achieve this aim I have tried a variety of hardware combinations over the last two months but am now at the point where I'm almost ready to abandon the project.In my current setup I have:Downstairs: A new & working Wireless Router (TP-Link TD-W8961ND) from which I can connect to (1) the internet, and (2) the internal network devices (NAS, printer, and network shares). Broadcasting on channel #1. DHCP = On.Upstairs: A new & working Access Point (TP-Link TL-WA801ND).The AP is connected by a physical cable to the downstairs router. The AP is in "Access Point Mode" with the same SSID and security settings as the router.
From the AP I can also connect to (1) the internet, and (2) the internal network devices (NAS, printer, and network shares). Broadcasting on channel #11. DHCP = Off.Clearly therefore, parts of my setup are correct and complete. However, I cannot roam between these two devices. Once a device is connected to one of these devices it cannot connect to the other. When downstairs, if I connect any device (iPad, iPhone, Win7 ThinkPad, WinXP Netbook) to the router's Wifi network, it connects to the router as expected and is fine.
When upstairs, it connects to the second router but cannot get to the internet (it gets an IP address beginning with 169.). It reports a "Strong" connection but simply cannot establish a useful connection with the world outside the house. The same is true if I take a machine that is successfully connected to the upstairs network and move downstairs.Have you successfully setup a wifi network with a TP-Link router and a TP-Link Access Point so that roaming works? If so, what's the secret?! Should I use the "Bridge with AP" mode for the AP?
I wish to turn my TP-Link wireless router into an access point but can't figure out how to do it. I have tried several times but without any success. Below are my information about my main router and the router I want to turn into an access point:
1- Main Router: TP-LINK 3G/4G Wireless N Router 300Mbps - Model No. TL-MR3420. url..
2- Router I wish to turn into an access point:TP-LINK Wireless N Router 150Mbps - Model No. TL-WR740N. url...
I am connecting to the internet in two desktops using the WAG120N modem+router.I have no problems with the internet. But when I try to use the wireless access point in my mobile phone / laptop,the device is not able to find the WiFi access point. I need to swith off the modem and start it again, then the devices are finding the access point. I guess this has to do with some amount of inactivity and the modem switces off the wireless access point. I there anyway by which I can turn off that setting ? I have tried the setting page but was not able to find anything.
View 6 Replies View RelatedI have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
how to set up a Belkin F5D7230-4 6000 router as a wifi access point. My home set up is the following: Dell Desktop connected by Lan to a Telefonica/Movistar router (I live in Spain), Dell portable .. connected by wifi at the other end of the house ..saying it's portable is a bit of a joke .. it's old and moving it is not an option ! Problem is I don't get much wifi signal on the portable to be able to do anything at all online so after googling on how to increase wifi signal .. worked out that I could set up an access point.. and owning a belkin router have been trying to set it up although I think there is something
I've connected the belkin by cable to the portable and disabled the DCHP and clicked on set up as an access point, set up wifi security and password, but when i am trying to reset the IP address I end up having to reset the router and start all over again.
I have a Windows XP SP3 desktop with a NetGear WG111v2 USB wireless adapter and I get my internet connection from my Blackberry 8320 (I connect my BBerry device to my PC and start Blackberry Desktop Manager and choose to use internet access of my phone for my PC). I want to be able to make this internet connection available to other devices on the network wirelesly. I also have a nook ebook reader and a laptop which I would occassionaly like to connect to internet via the connection described above. How to go about making Blackberry internet connection shared accross the network? I tried Internet Connection Sharing Wizard, but I ended up with nothing to show up for.
View 3 Replies View RelatedI have an E2500 running as a router/DHCP server. For reasons beyond the scope of this question, I am replacing the router and DHCP functions with a SonicWALL device. I would like to continue to use the E2500 as a wireless access point only, providing WiFi connection to the SonicWALL. How do I set up the E2500 for this purpose. I assume I switch off the DHCP server and NAT within the device. Is there a dedicated "access point" mode?
View 9 Replies View RelatedWe have an RV042 router.I'm looking for a solution where my drop-in clients would have their own WIFI key to access Internet, with no access to our LAN.
-Can I place a Wifi AccessPoint on the DMZ so my drop-in clients use it to connect to the WEB.
-While putting another Wifi AccessPoint on a regular LAN port for Employees to use and stay within the LAN?
I need a wifi extender for wag 120n , and i want to connect it with WDSI use wag 120n as main and only modem and access pointWhat is the best and cheapest device for me?
View 1 Replies View RelatedI have an existing home network with a D-link wireless router, IP 192.168.0.1. In the past, I set up another of the same model Dlink router as a WAP to extend my network by simply disabling DHCP and setting its IP to 192.168.0.100. Used the same SSID and passwords, worked flawlessly. Now, my WAP-router has failed and I purchased a LINKSYS E2500 to replace it in that function. I'm trying to configure it the same way but am having problems.The Linksys' IP is 192.168.1.1 by default. I hooked its LAN port to my laptop and accessed the setup page at 192.168.1.1. I changed the router IP to 192.168.0.200 and disabled DHCP. I saved settings, the router reset, and since, I am unable to re-connect to that router setup screen at either 192.168.0.200 OR the default 192.168.1.1. I reset the router to default and tried this multiple times but could never get back to the setup page (didn't even configure any wireless settings yet) after I made the IP change and disabled DHCP. With my previous router, this worked easily and flawlessly.
1. What am I doing wrong (ok, other than using Dlink components)?
2. Should these two different brand components work ok together llike this or is that a problem?
3. Why should unticking DHCP and/or changing the IP address as described make the device unreachable?
I would like to use the DAP-1522 as an Access Point (wired to my router). My two concerns are:Can the 3 remaining ethernet ports be used to wirely connect to local PCs (so the DAP-1522 also acts as a switch) ? In case answer to the previous is yes, would it affect the performances of the wifi ?
View 3 Replies View RelatedI have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies View RelatedI have the Netgear wndr4500 router setup as an AP. The wndr4500 has a feature for guest wifi but will not connect to the internet. The main wifi will connect to the internet fine. I'm wondering if I use the WNDR4500 as an AP, the guest features do not work?
View 2 Replies View RelatedI've been having trouble with my wrt54gs2 and 4 360's. I tried a link someone posted for me to a cisco tutorial, it worked, but only for one 360. I have a Netgear wndr3400, I HATE the wireless on that router. Its unreliable but I like the features, the guest network and transfer meter, plus its worked with 4 360's out of the box. So would it be possible to turn off my wifi on the Netgear and plug the wrt54gs2 in and use its wireless?
View 7 Replies View RelatedI use a Cisco 871W router for my office in home -- I have Wifi working and want to add my new Blu-Ray player to the network -- I bought a WAP54G to use as a wireless bridge assuming i woudl just connect the WAP to the BLU-Ray with a ethernet cord. The instructions for installation of the WAP include connecting it to my router for the set up but the installation disk says it is not recognizing the WAP. I use Brighthouse for my ISP and the connection sequence is BH Modem to teh Cisco 871W -- the 871W directly connects to my CPU and to a Net gear FS105 fast network Switch -- the swicth connects to my VOIP phone , HP printer and external HD back-up system -- there is an open port onthe FS105 and two open LAN ports on the 871W.
I tried to install the WAP but connecting it to both the router and the swtich without luck. Is the WAP what I need to connect the Blu-Ray --- am i missing something in the set up?
I am having trouble connecting my device to certain WiFi networks. We work with hotels and we have a handful of devices that are just not able to connect to their network. Te device works fine in my office. When I get to the Setup page and do a site survey, it'll get to 100% and then display a "page can't be found" as oppose to showing me that it has been connected. We had the MAC address cleared in their network and still no luck. Firmware has also been updated.
View 7 Replies View RelatedI just recently bought this router (DIR-615 rev E3) to act as a Access Point for the dead wifi spot in my room downstairs. I set up everything properly (Turned off DCHP, set ports and gateway..subnet blah blah) and it was working fine. My wireless speeds were perfect, and had no issues with that. However, my wired speed was significantly slowed down. I have Verizon Fios and have the wire from that plugged in to LAN port 1 on my DIR-615. I have another wire going from Port 2 to the back of my PC. My normal speeds are about 30mbps down and 25mbps up. When I connect my internet through the second router (DIR-615) I get a maximum of about 3.0mbps up and down, doesn't go much higher than that. The wireless however, gives me about 11mbps both ways, which is fine.
I thought it might have been a firmware issue so I flashed to DD-WRT (build 15778), but the problem persists. I've tried most everything and am getting desperate. There's absolutely no logical reasoning for the slowdown. I have confirmed it's a router issue because I also turned off wireless on my laptop and plugged that directly into the router instead of my desktop and get the same 3mbps.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View Related