Netgear WNDR4500 - Clients Not Showing Up In Clients List
Jul 6, 2012
I have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
I've got an E4200v1 running 1.0.04 firmware with guest access enabled. I'd like to find out who is logged in using the guest access. Is there a way to get a list of the DHCP clients on the guest network? I'm able to do this for the non-guest access via the WEB interface's Status->Local Network->DHCP Clients Table page. But I can't find a similar table for the guest network.
Wireless clients drop off Netgear router - Running a Netgear router in home. Have one desktop PC, 2 printers, 1 Mac and 3 Windows laptop connected. The devices that connect wirelessly will drop of the router in a random way. One printer, an HP all in one, will no longer function and I have to pull the plug to de-energize and restart it. My wireless network is a mess. I have called Netgear and for the first two months they had me change channels and adjust other settings which seemed to work at first but then these symptoms all came back.
I know that N operates on both 2.4Ghz and 5Ghz, whereas AC operates only on 5Ghz. Yet many AC routers advertise as operating on both 2.4Ghz and 5Ghz. So what happens when you connect to an AC access point on 2.4Ghz? Does that operate using 802.11n?
What happens when you try to connect to an 802.11ac access point using an 802.11n client on 5Ghz? Is this possible, or are legacy connections only possible at 2.4Ghz?
I have a Netgear WNDR4500 (802.11n, dual band) currently that I am very happy with. I figure I will eventually switch over to AC. I'm trying to determine if I would be better off simply replacing the N unit with an AC unit, or running both (perhaps WNDR4500 to handle 2.4Ghz clients, AC access point to handle 5Ghz clients, or similar).
I have time warner internet service and just upgraded my service to their extreme internet. In doing so I had to change my modem to a docis 3.0 modem; the motorola sbg6580. Its a modem that has a router and wifi built in but its really bad and not nearly as good as my net-gear router.
Added a wireless router to our office here so that people with laptops could get on the net without having to physically plug in. Right now it is ok, but the router is acting as it's own DHCP server instead of our server here assigning out the IP's.
The main gripe I have is I can only login to the router through my phone and not through my computer. How can I achieve this. We have multiple offices that all connect through a VPN. I would like our sys admin to access the router at his location as well.
Do I just turn off DHCP on the router and thats it? The model is Netgear WNDR4500.
I have the Netgear wndr4500 router setup as an AP. The wndr4500 has a feature for guest wifi but will not connect to the internet. The main wifi will connect to the internet fine. I'm wondering if I use the WNDR4500 as an AP, the guest features do not work?
I have problems with my D-Link DIR 635 router. It shows up fine in list of networks on my girlfriends Mac and on my new laptop, but on my older laptop it doesnt show up at all (whereas a lot of other networks do). Seeing as my current laptop is being repaired at the moment, I need to be able to connect to the net with my old laptop too.
I run Windows XP Professional on my laptop, which is a Compaq Presario f700. why the network doesnt show up?
I just started having this problem yesterday. I was experiencing weird downloading/internet browsing issues and couldn't figure out what the problem was. I started looking around my router settings and noticed that in my DHCP Client list, my computer isn't in it. The router is hooked up to the computer, so it's not wireless. My phone and my girlfriend's laptop are listed, but the main computer isn't. It's especially causing problems with port forwarding. Downloads will stop because the port isn't showing as open. I'm running 64 bit Windows 7 and a Belkin N+ Wireless Router, model F5D8235-4.Firmware is up to date.
When I'm home I can get online but it's slow webstar. I used to be able to get online at the local McDonalds with free wi-fi, real fast. Now, the connection list doesn't show the "FREE McDonalds" connection.
I have: Atheros AR5B97 Wireless Network Adapter, Windows 7 on ACER Aspire 7741z-4815. It has been updating until recently, don't know if it's because I haven't been online as often or what.
I have an EA4500 and am using Cisco Connect Cloud software. Its working mostly fine except that I have one device on the network that will not show up in the device list. This is not an issue in itself and normally I would ignore (although it used to show up when I forst got the router) however..
The device is a WDTVLive media unit and required access to windows shares on a media server. Now the WDTVLive device is server an ip address by the router and is available from everywhere on my network but every couple of days it loses the capacity to search windows shares.
I know what you are thinking and I initially thought the same, this is an issue with the WDTVLive box. However one day I spent a few hours trying to resolve (Am an IT Consultant and know a little about networks) and found that I could not fix the issue. I then rebooted the router and it started working. I have since confirmed that every time it breaks I have to reboot the router.
Why is my WRT54g router only showing the 1st LED port is lit, and not the rest when I have changed or added a device to the 2nd,3rd,4th port? It is also stopping my ability to stream,view youtube etc. When I disconnect the router from my cable provided modem, everything works fine?
I just got a DIR-655 and set it all up pretty easily. I have 6 wired and 3 wireless. All work fine and all are set to use DHCP. But if I go (in the router) to the Lan Computers list under Device Info, three devices (2 wired, 1 wireless) do not appear. I do have a switch added to the system, but of the three devices connected to it, 1 shows in th Lan Computers list and the other 2 do not.Since everything works, I'm mostly just curious why this is. Every previous router I've had showed everything correctly.
I have purchased E2500 and i am having following problems:
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button 2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
I have upgraded to latest firmware and also peformed reset as directed by support.
I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.
They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.
My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.
According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?
I'm having a tough time with VPNing into work.I'm the network admin.I set up the Windows 2003 RRAS server. I'm finding that the remote clients have "either / or" connectivity.Once a client is connected, it either has local Internet without LAN resources OR it has the needed LAN resources but no local Internet.I can watch continuous pings work, fail and start up again depending on the VPN connection.
I have had trouble with my DIR-651 router since i bought it. To put it simply, if there a device connected to the wireless network, no other device can connect. Here are the devices i have:
hp pavilion running fedora 15 hp touchpad (webos) htc thunderbolt (android) dell inspiron (? work computer..not here right now) running windows xp
I am running wpa 2 using AES encryption in wireless mixed b/g/n mode (I have tried all other permutations of BGN. On the devices that will let me see error logs, all i get is "authentication invalid" errors.) In a few rare cases, i am able to get a second device connected by disabling the first device, connecting second, and reconnecting first.I am running the newest firmware 1.10NA.
Client authentificates on ASA via certificate, and after successful authentification I want to Authorize my clients on ACS with DACL association per client. ASA get username from CN-field in certificate, and sends to ACS, ACS respond to ASA authentification fail, password incorrect, and no DACL assign happends. How can I define in ACS that it should be only authorization process without any password, just username from certificate?
Once a client connects to my VPN (VPN Client 5) they can not see anything other than the outside interface. If I ping anything on the LAN for example I get a reply from the outside interface. I can not see any WAN either (even by IP) My LAN clients can see the clients within the VPN Pool. I would like all traffic to flow through the VPN. I have tried split tunneling to verify if the internet would work and local lan would stay connected. It does work but I was still unable to access anything on the remote netwok. I am not sure if I am missing a nat command or something simple.
The current setup is as follows. 881 Router with windows 2008 radius authentication. The client is authenticating and reciving an IP address from the local ip pool. Please see below for the running config.
On every floor there are 10 rooms which can have multiple clients (laptops, ipads, smart phones) so let's say 50 clients.how to set up whole thing so the users in every room have decent speed for surfing and watching videos online [code]...
When I go into the Network Settings, and the end of the page I find a list named "Number of Dynamic DHCP clients: 7". As far as I know, I should only see 4, all 4 laptops; however, I see 2 UNKNOWN entries in this list, and one name "Macondo". Each of these entries have an option (a link) saying "Revoke" and other "Reserve". I am just wonder if these entries are intruders in my home network. What should I do? I am afraid to break my internet connection. By the way, I set up every single one of my family 4 laptops at home with a WPA-PSK using a very long key.
I just want to keep one PC as a server and one switch connect to it (For LAN). I want to connect multiple client/screen to that server, so I can use single servers for multiple screen/client.(Client machine will not have any CPU, they will utilize servers memory.)
I have a TP-Link TD-W8960N Wireless Router. I would like to know what the I.P. addresses of connected clients are (both those connected wirelessly & those connected by Ethernet cable). There are about 6 computers in my network, some have dynamic and others have static I.P. addresses.I am finding it difficult to navigate the router,on which menus get me to the information that I am interested in
I've just discovered this thing in Windows Event log. The DHCP-Client log is full with this: the client received a NAK from the DHCP Server. Strangely, they still get the desired IP address. (Which are reserved adresses for the MAC adresses.)So I've looked at the logs in the DIR-615 (rev.D, FW: 4.13), and found this:
I have a Cisco 2921 Router with actually no clients working on it but the CPU temperature is 76 degree celsius. Is this normal? I think this is too hot.My room is aircondishened to 21 degree celsius. What can I do?
Is it possible to set up a pppoe client on a VLAN interface, or a switch interface associated to an VLAN?. For example, in a 881 ethernet router, could I configure a pppoe client on any of the lan interfaces in addition to the pppoe client configured on the WAN interface?.