Linksys Access Point :: No IP Via DHCP And No Internet Connection On WAP300N
Mar 17, 2013
To extend my wired ethernet I have purchased a WAP300N access point and connected it according to the instructions. I can see the AP from a wireless client and connect, but no IP number is provided to the client. The AP is connected to a router which has a DHCP server via wired connection (though a switch). The AP does it self get an IP number from the router but does not pass through DHCP requests from the clients.Occasionally an IP number is provided, but then there is no route to the LAN or the WAN on the other side of the AP.I have tried a whole lot of things to make it work (and been in the internet chat for two hours with a Linksys supporter, who could not make it work either).I have tried to set the IP number in the AP to static.I have tried to remove security (has to be WPA2 eventually, but for the sake of testing it has been removed)I have tried to factory resetI have tried to reinstall the firmware (the same version as the factory installed)etc.
View 4 Replies
ADVERTISEMENT
Apr 27, 2013
I recently purchased and installed seven WAP300N access points in a school, but they are now having intermittent problems with network access, as of right now their network is completely unusable. Specifically there appears to be a conflict between these access points and the gateway/router which provides their network clients with addresses via DHCP; BUT in the three years I have been assisting them the DHCP server on their Cisco router has never before given any problems!
All WAP300N units are wired to the network acting as standard access points and setup to pickup their address automatically via DHCP. When the problem first arose I changed to offending unit to use a static IP address to avoid what I presumed was an address conflict; however the same problem now appears to be happening with the other units as well!
My understanding is that these WAP300N units do not have any in-built DHCP server capability, is this correct ?If not, how I can disable this feature.Otherwise, it would seem to me that the units must be incorrectly using the default gateway address which they are getting from the DHCP server as thier own IP address. Unfortunately assigning static IPs to each access point is not possible as these are controlled by another group and the existing allocation is now used up.
View 5 Replies
View Related
Aug 18, 2011
I have a new notebook Sony Z217GG, I connected WAP 4400N was very smooth, but after connected WAP 4410N, the internet connecting always connect and disconnect, I check the notebook wireless model is intel 6230.
View 1 Replies
View Related
Dec 9, 2011
I've some strange things with my WAP610.I connect it to my lan, my DHCP server assign an IP, that's normal way..I lookup for this IP, and fill in the address field in my IE (firefox or safari I've tried all of them).... the AP ask me password and user... I fill in the password field... and get into config...
So I think it could be a bug with static IP... I'll try on the wireless security... select "manual"... change nothing (leave default value) click save... wait a while... connect on the DHCP ip, return to the wireless page... and lost a lot of time since nothing is saved.
View 7 Replies
View Related
Oct 16, 2010
I set up my internet access by adsl modem as gateway, then RV042 as load balancer and dhcp server, security by MAC address restriction and static IP assignment. WAP 610N used as access point.works great for first few weeks, then somehow I can't access the network.I've been using linksys on my SOHO network, no problem before (RV042+WAP54g)
View 9 Replies
View Related
Oct 27, 2011
I use the WAP610N as an Accesspoint for only an small Mobilephone to WLAN Printer Network.My big Problem is that i have therefore no DHCP Server in this special small WLAN Network.And now i need an own DHCP Server from the Accesspoint side because otherwise i must use static IP Adresses in all Mobilephones to connect with the WLAN Network .In the WAP610 unfortunately there is only the choose between static IP Adress and IP Adress FROM an existing DHCP server .
View 2 Replies
View Related
Apr 24, 2011
I have a Windows XP SP3 desktop with a NetGear WG111v2 USB wireless adapter and I get my internet connection from my Blackberry 8320 (I connect my BBerry device to my PC and start Blackberry Desktop Manager and choose to use internet access of my phone for my PC). I want to be able to make this internet connection available to other devices on the network wirelesly. I also have a nook ebook reader and a laptop which I would occassionaly like to connect to internet via the connection described above. How to go about making Blackberry internet connection shared accross the network? I tried Internet Connection Sharing Wizard, but I ended up with nothing to show up for.
View 3 Replies
View Related
Aug 26, 2012
The detected problem is the connection between my access point, router, or cable modem and the Internet is broken.The network gateway is accessible, but Windows couldn't receive network traffic from the Internet.All other devices (iPad, Xbox, android phone) have no problem connecting to the Internet.Desktop is the only one experiencing the connection issue.
View 1 Replies
View Related
Jan 31, 2012
My laptop died last week and have been using my husbands, which I hate! We had some issues with computer freezing on some webpages or after being on webpages for awhile (like facebook). Yesterday it froze and I could not get it back on. When he got home he did scan disk (which I also did) and got it working after going into safe mode and doing system restore. He said an update had gotten through and messed things up. Anyhow, after he was on it a few hours last night, we lost connection. I figured the crazy weather was the culprit but it has been off all day. Our router is working and connecting but the adapter is not. Also our home phone says there is no line. We have unplugged everything several times, checked to make sure everything is in the right spots, I have even reset the router and rebooted the adapter. I uninstalled and restalled the adapter also. It is now telling me that "the connection between your access point, router, or cable modem and the Internet is broken". The only lights I have on the adapter are power, battery, DS and now the US light is blinking. The online and link lights are not on.
View 3 Replies
View Related
Aug 20, 2012
I just bought a WAP160N to replace our WAP54G because my Samsung Glaxay 3 could not use the internet through our WAP54G (not sure if Galaxy 3 doesn't like G mode networks). The problem we have after installing the WAP160N is that the signal doesn't extend as far in the house as the WAP54G. We have the routers up the front end of the house (the WAP160N is wired to our Netcomm router) and when you go to the kitchen (in the middle of the house) the signal from the WAP160N is being lost/fluctuating, then dropping on devices such as iPads. We have WAP160N set to mixed mode on 2.4Ghz, AES or TKIP. I tried setting it to 5Ghz but that didn't work either. We always had signal strength in the kitchen when using the WAP54G. if the WAP160N can not extend its signal further or the same distance as the WAP54G? I find it odd that the iPads can't hold the connection in the kitchen, when we've always been able to use internet/wifi there. I'm thinking of returning the WAP160N if the signal cannot extend far enough. router that can extend the signal far throughout a house?
View 1 Replies
View Related
Jun 11, 2011
i am trying to connect my new Iphone 4 to my wireless connection which is a cisco wap610n. I get a fails to connect error. mine and other laptop can connect using my security key. the Iphone can connect to other wireless connections. my access point connects to a linksys RT31P2 router?
View 1 Replies
View Related
Jan 21, 2011
I have 2 WAP54G AP. I have office with internet connection near my home. How to connect these access points so i can get access to internet from home, but don't won't to anyone else can access that.
View 1 Replies
View Related
Oct 12, 2011
I have a problem about no connection on casio handy terminal when two access point were power on. The devices were link with Cisco access point. for the other one i use dlink access point for the wifi function. I need to switch off dlink access point to make the connection between the device and the cisco access point.
1st access point :
Dlink DAP-1360
Default IP: 192.168.2.29
Channel:1
SSID Broadcast: Enable
2nd access point :
Cisco Aironet 1240AG
Default IP: 192.168.3.33
Channel:6
SSID Broadcast: Disable
View 1 Replies
View Related
Jun 13, 2011
I had the WAP610N for a few months with no issues. As always, I have a custom SSID and password, using WPA2. All of a sudden, none of my mobile units (at least 5) are unable to connect via the WAP610N. However, I can connect to a Netgear N750 w/o any issues. When I reboot the WAP610N, it resolves the issue for a few minutes, but then behaves the same as before. I know its not my network because, I am able to connect via wired and wireless via the Netgear. I verified via the web interface that none of the settings/configurations have changed - but still nothing. Latest firmware has been applied. Note sure If I should perform a factory reset or re-apply the firmware.
View 2 Replies
View Related
Jul 16, 2011
I'm trying to share my existing wireless connection over a WAP54G with the latest firmware, on Windows 7 on a laptop. Basically, the laptop is getting a wireless connection from my Sprint Card, but I need to share a wi-fi connection with an iPod I'll be using to validate tickets. Unfortunately, there is no option to share the wireless connection when I click on the Properties for the connection. When I put in my WiFi settings, the iPod is able to login to the AP, but it cannot obtain an IP. It keeps doing this. Same thing happens with my Samsung Epic which runs Android. I can access the AP manager, and can configure it. Have tried using no security, but still no dice. Even turned off the firewall.
I can surf the internet on the laptop, but I simply can't share the connection with the AP. This is really important as I'm trying to get it setup by next weekend!
View 2 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jul 7, 2011
When the WAP54G is set up as a repeater for a WRT54G, will a computer connected to the LAN port on the WAP54G be able to connect to the network? I know it will see the WAP54G if I manually set it's ip address.
I guess I want it to act as a wireless NIC for the desktop while also operating as a repeater. Is this possible? If not, will one of the other AP settings like Bridge allow the wired connection to connect to the other side of the network and give wireless access to wireless devices? I've hacked up and attached one of Linksys's diagrams to show what I'm trying to do. It seems to me the easiest thing to do would be to buy a wireless NIC for the desktop.
View 5 Replies
View Related
Mar 3, 2011
I work at a small business that has an exisiting wired network. Our setup is: Internet > ISP Box > DHCP Server > Switch > Users. I have been attempting to add a wireless router to the network to enable our shop techs to wirelessly access our file computer. I have managed to get the wireless working, but the network was not visible, I could not access any network computers from the wireless, and I could not access the wireless router from our main server. After this I screwed up the settings completely and even a wired connection to the router couldn't connect to the internet. Now I have purchased a WAP54G, but I forsee the same problems when I go to config everything tomorrow.
View 2 Replies
View Related
Jul 21, 2012
I have a static IP given to me by the service provider, and I need to make the Access point as a DHCP server to provide me IPs inside my LAN.I have created a DHCP pool in the AP. But do I have to NAT the public IP onto the private DHCP range ? This setup is possible.
View 12 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Jul 11, 2012
I reset the wap610N,after establishing connection, my iphone see my network domain but does not connect. I heard of dual band setting,how do i go about that. What must i do to establish connection with the iphone.
View 4 Replies
View Related
Aug 10, 2011
I am setting up an autonomous 1142 Access Point. The intended goal is to get it accessible though 2 SSIDs:Private: VLAN3 (our internal data VLAN)Guest: VLAN98 (our DMZ/Segregated VLAN)At present, our VLAN3/internal users get DHCP addresses from x2 Windows DHCP servers. Eventually, the DMZ VLAN connections will get their IP addresses from a switch in our DMZ VLAN.At the moment, I am able to authenticate with the Access Point through the VLAN 3 SSID but never get an IP address. I have posted the switch port config below as well as the Access Point config.
View 2 Replies
View Related
Jan 4, 2012
I have an AT&T Gateway Wireless router to connect to Internet with my wired computer. In another room, I have another wired computer I also use to connect to Internet. I never have problems connecting to Internet from computer that is hooked up to the router, but I often have Internet connection issues from the computer in the other room. It can find the access point, but not connect to Internet. I reinstalled the WUSB300N driver again, but I still cannot connect.
View 2 Replies
View Related
Mar 29, 2013
I have a DCP 3925 with 2 telephone and 4 internet ports.So, how can I combine DPC 3925 + E3000 to have more internet ports? and wich one is the best wifi than I can use ??Main router is the DPC 3925, where the internet is connected.
View 9 Replies
View Related
Oct 3, 2011
I have a Cisco 870 integrated service router and 3 Cisco Aeronet 1180 Access Points.I have configured the router to act as a DHCP server. with all four /26 subnets in a seperate address pool.the first one is for the routers wireless interface and works fine.but the other 3 are for each of the wireless access points, that are used for internet access, but have to operate independently (i.e. the clients on each must not be able to access anything other than the devices associated with that access point and the internet.
The problem I are having is that the router doesnt distribute DHCP information via the access points so the clients on all the access points are not recieving any internet connection at all, but are connecting to the access points, and the LED for the access points suggest that they are connected t the router, the router accnowledges their existence but is not transmitting through the fast ethernet switch ports. but is communicating with a wired printer that is associated with the wireless vlan.
Each access point is on its own vlan, and the switchport access vlan command has been used. only the five static addresses have been excluded from the address pool. the router, the three access points and the printer adresses are static. the printer is working despite being the only device on the /24 network all other addresses are on the /26 networks. this to my knowledge shouldent work but it does, which is handy because the printer software doent support subnetting.The simulation I have ran say that only the printer shouldent work, but its the access points that are not working how they should. I have studied the configuration of the router and access points, and came up empty on why they are not recieving DHCP information.
I are not even able to telnet to them, despite having an address setup. I have not set up a routing protool on the router due to it being the only router. I have checked the interfaces fa0 to fa3 and they are line up protocol up, the wireless is line up protcol up, the vlans are line up protocol down, except the one asociated with the wireless which is line up protocol up (I believe the protocol only goes up when a device is connected to it).
View 9 Replies
View Related
Aug 25, 2011
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies
View Related
May 10, 2013
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
View 1 Replies
View Related
May 1, 2012
Is it possible to configure WRT120n as an access point?
View 1 Replies
View Related
